ismoka Magoo User manual

Notice for Use
Thank for choosing iSmoka products! Please read this manual carefully before use
to ensure that your usage is correct. If you require additional information or have
questions about the product or its use, please consult your local iSmoka agent, or
visit our website at www.ismoka.com.
Product Introduction
With all the parts detachable, Magoo has been added more flexible features,
whose liquid volume and air inflow are adjustable. Seeing from the individual
window of liquid level, the liquid volume is more intuitive. What’s more,
customers can choose pluggable mouthpieces according to their own favors.
From this product, people can also enjoy the fun of DIY, as customers can
replace the heating coil (single and dual) and entire atomizer head by
themselves. In addition, the scalable positive pole contact can better adapt and
protect the battery contacts.
Components
1* Mouthpiece Cover
1* Tube Cover
1* Mouthpiece
1* Metal Tube
1* Clear Tube
1* Atomizer Head (Part A, Part B)
1* Atomizer Base
Product Parameter
Length: 71.7mm
Diameter: 23mm
Magoo
User Manual
Atomizer Base Atomizer Head
Part A Part B Clear Tube
Metal Tube Mouthpiece Tube Cover
Mouthpiece Cover
Mouthpiece CoverClear Tube
How to assemble
Firstly, screw the atomizer head onto the atomizer base; secondly, screw the
mouthpiece to the atomizer head; thirdly, screw on the atomizer tube, then the tube
cover; at last, the mouthpiece cover.
Atomizer Base Atomizer Head Metal TubeMouthpiece Tube Cover
1 2 3 4 5
71.7mm
23mm
How to replace the heating coil
Single heating coil: first, wrap the heating coil on the middle of the delivery
string for several laps with both ends left enough length to reach the bottom of
the atomizer head A. Then wrap the ends on the atomizer head part A,
separately nipped by the plastic ring and the silicon ring, which are the positive
and negative conversion. Finally, put the delivery string into the matching slots
and screw the atomizer part B on.
Delivery String
Heating Filament
Heating Filament
Heating Filament
Delivery String
Silicon Ring
Plastic Ring

How to add liquid
Unscrew the mouthpiece cover and refill the liquid from the inwall of the tube
cover. You can see the liquid level from the plastic part of the atomize tube. Please
do not fill it completely full.
Functions
1. Since there is an air inlet in the atomizer base, by screwing the thread ring on
the atomizer base, the size of the inlet could be adjusted so as to control the air
inflow.
2. When the mouthpiece was screwed, the fluid volume that flows into the atomizer
head could be controlled, which determines the vapor volume.
3. The heating coil and the entire atomizer head could be replaced by DIY.
Precautions
1. Only have your Magoo repaired by iSmoka. Do not attempt to repair the unit by
yourself as damage or personal injury may occur.
2. Please don’t put the Magoo under high temperature or damp conditions, or it
might be damaged. The appropriate operation temperature is within 0℃to 45℃
while charging and -10℃to 60℃while using.
3. Do not cast it or place it with anything sharp;
4. Do not detach it or lay it flat on the table when it is not in use, as it may cause
leakage;
5. Do not assemble it with products of other brands, if it is damaged or is unable to
use by this reason, iSmoka will not take any responsibility.
Warranty
Please consult with iSmoka distributors for their warranty and return policy. We are
not responsible for any defects caused by human error. Our warranty is not
available for products purchased from third party vendors.
plastic partplastic part
Shenzhen iSmoka Electronics Co., Ltd.
Email:[email protected]
Web:www.ismoka.com
Dual heating coil: the detail of each coil is just the same as the single one.
The only difference is that the dual one has two crisscrossed slots, so you
should match them with two delivery rings.
Delivery String
Heating Filament
Plastic Ring
Heating Filament
Delivery String
Silicon Ring