ISTCONTROL IRD2M User manual

ID
Mobile/RFID Reader
(IRD2M)
Installation Guide
Version 1.0.0
Safety instructions
Observe the following instructions to use the product safely and prevent any risk of injury or property damage.
Warning
Noncompliance of instructions could lead to serious injury or death.
Installation
Do not install the product in a place with direct sunlight, moisture, dust, or soot. A fire or electric shock may
occur.
Do not install the product in a place with heat from an electric heater. A fire or electric shock may occur due to
overheating.
Install the product in a dry place. Otherwise, a product damage or electric shock may occur due to moisture.
The user should not install or repair the product independently. If the product has been damaged due to
independent installation or repair of the product by the user, free A/S service will not be provided.
Caution
Noncompliance of instructions could lead to minor injury or product damage.
Operation
Do not allow liquids such as water, beverages, or chemicals get into the product. A fire, electric shock, or
product damage may occur.
Installation
Do not install the power supply cable in a place where people pass by. Product damage or physical injury may
occur.
Do not install the product near a highly magnetic object such as a magnet, TV, (especially CRT) monitor, or
speaker. A product failure may occur.
If installing the product outside where the product is completely exposed, it is recommended to install the
product together with the enclosure.
Keep the minimum separation distances between the devices when install multiple devices. Otherwise, RF
performance is affected to the other device, the devices may not operate normally

•Components
IRD2M reader 1 ea Wall mount bracket
1 ea
Wall fixing screw 2 ea
Bracket fixing screw 1ea
•IRD2M Reader •Wall mount bracket •Wall fixing screw •Bracket fixing screw

•Specification
IRD2M reader supports RFID protocol of 13.56Mhz RFID : ISO/IEC 15693, ISO/IEC 14443 A/MIFARE , ISO/IEC 14443 B ,
Felica, ISO/IEC 18092(NFC IP-1) and Bluetooth and NFC protocol for mobile communication.
•Mobile ID (Bluetooth, NFC) reading
•Mobile ID Manger App (Reader setting app) communication
•ISO 14443 A/B, ISO 15693 RFID card reading
•26, 32, 34, 37 bit Wiegand data output
•ICON LED indicator of 4 external input signal (ex. access granted, access denied, door open, door locked)
•3 Color LED indicator (RED, GREEN, BLUE)
•Buzzer Control
•Tamper Alarm
•External input signal output in wiegand
Base Part
Number
Input
Voltage
(VDC)
Current
Operation
Temperature
Cable Length
Standby
AVG
Max
AVG
Peak
IRD2M
12V
250mA
300mA
400mA
-20℃~50℃
Wiegand : 22 AWG (150m)
24 AWG (90m)
RS-485 : 4 AWG (1,200m)
24 AWG (500m)
•Name and function
Bar LED indicator
Icon LED indicator
RF card
authentication part
IRD2M slim type reader

•Connection
PIN
English
한국어
Color
색상
1
PWR +VDC
Red
빨간색
2
PWR GND
Black
검은색
3
WG DO
Green
초록색
4
WGD1
White
흰색
5
485 TRXA
Yellow(Gray Stripe)
노란색 (회색띠)
6
485 TRXB
White (Gray stripe)
흰색 (회색띠)
7
RED LED
Brown
갈색
8
GRN LED
Orange
주황색
9
BUZZER
Yellow
노란색
10
TAMPER
Violet
보라색
11
EXT IN1
SKY
하늘색
12
EXT IN2
Blue
파랑색
13
EXT IN3
Pink
분홍색
14
EXT IN4
Gray
회색

•Installation
1. Select a proper place to install and put the wall mount bracket. Fix the bracket with wall fixing screw. Try to keep
minimum distance of 500mm between readers.
2. Make wire connections referring connection table.
3. Put the reader on the bracket fixed on the wall.
wall
IRD2M slim type reader
IRD2M slim type reader

4. Fix the reader to the bracket with bracket screw
Wall
IRD2M slim type reader

•Dimension
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own
expense.

• Bluetooth Transmit Power: 8.65 dBm
•Bluetooth Frequency: 2402~2480 MHz
•NFC Frequency: 13.56 MHz
•RFID Frequency: 13.56 MHz
For more information, contact us at the following contact information.
ISTCONTROL, Inc.
Access Control & Integrated Solution Provider
1203, 37, Maebongsan-ro, Mapo-gu, Seoul, Republic of Korea 03909
TEL: 82+ 070-4194-1993
Website : www.istcontrol.com
Email: [email protected]
10
FCC compliance information
FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
Modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment
under FCC rules.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC ID : 2AZS5IRD2M
EU Declaration of Conformity (CE)
This product is CE marked according to the provisions of the Radio Equipment Directive (RED) 2014/53/EU.
Hereby, ISTCONTROL declares that this product is in compliance with the essential requirements and other
relevant provisions of Radio Equipment
Directive (RED) 2014/53/EU.
T his device meet the E U requirements on the limitation of ex posure of the general public to
electromagnetic fields by way of health protection.

DeclarationofConformity
ManufacturerName: ISTCONTROLCO.,LTD.
ManufacturerAddress: #1203,12F,37,Maebongsan‐ro,Mapo‐gu,Seoul,Republicof
Korea
ImporterName*:
(Orauthorizedrepresentative):
*IfmanufacturerisnotinEU
UnderArticle10(2)and10(10),therearenorestrictionsofuse
ImporterAddress: ‐
Declareunderoursoleresponsibilitythattheproduct
ProductType/Description: SmartRFIDCardReader
Model: IRD2M
VariantModel: ‐
TradeName: ISTCONTROLCo.,Ltd
ProductIdentificationElement: IRD2M
ProductAccessories(ifapplicable): N/A
Hardwareversion V1.01
Softwareversion V2.00
Isinconformitywiththefollowingstandardsorothernormativedocuments
Teststandards
Radio:ETSIEN300328V2.2.2(2019‐07),ETSIEN300330V2.1.1(2017‐02)
EMC:ETSIEN301489‐1V2.2.3(2019‐11),ETSIEN301489‐3V2.1.1(2019‐03),
ETSIEN301489‐17V3.1.1(2017‐02)
Safety:ENIEC62368‐1:2020+A11:2020
Health:EN62311:2008
Weherebydeclarethat[allessentialradiotestsuiteshavebeencarriedoutandthat]theabove
namedproductisinconformitytoalltheessentialrequirementofDirective2014/53/EU.
TheconformityassessmentprocedurereferredtoinArticle17anddetailedinAnnex[III]ofDirective
2014/53/EUhasbeenfollowedwiththeinvolvementofthefollowingNotifiedBody(ies):
PHOENIXTESTLABGmbH(NotifiedBodyNumber:0700)
Königswinkel10D‐32825BlombergGermany
EU‐TypeExaminationCertificateNo.:
TheTechnicaldocumentationrelevanttotheaboveequipmentwillbeheldat
Name: KwakJungHyun
Title: President
Address: 1230, 37, Maebongsan-ro Mapo-gu, Seoul, Republic of Korea
Date:November2,2021
SignatureofAuthorizedperson