iSystem Infineon TC377TE User manual

Infineon TC377TE Compact Emulation Adapter
User Manual
V1.0

This document and all documents accompanying it are copyrighted by iSYSTEM AG and all rights are
reserved. Duplication of these documents is allowed for personal use. In all other cases, written consent
from iSYSTEM is required.
iSYSTEM AG. All rights reserved.
All trademarks are property of their respective owners.
www.isystem.com

Contents
Infineon TC377TE Compact
Package content ...................................................................................................................................... 5
Operation ................................................................................................................................................... 6
Configuration ........................................................................................................................................................................................................................7
Mechanical information ......................................................................................................................... 8
Accessories ............................................................................................................................................. 10
Schematics ............................................................................................................................................. 11

Infineon TC377TE Compact
Infineon TC377TE Compact Emulation Adapter has been custom designed to achieve a
minimum vertical size of the LQFP292 adaptation. It provides full trace capabilities for the
TC327LP, TC337LP, TC367DP, TC377TP (BGA) devices where the trace port is not available or
lacks the full trace capability.
Infineon TC377TE Compact Emulation Adapter supports the following debug and trace
interfaces:
· DAP
· AGBT (Aurora Gigabit Trace)
iSYSTEM Debug and Trace solutions
Trace provides a non-intrusive and deep insight in the embedded application without
influencing real-time behavior. It can be used to debug the most difficult and complex code
defects and offers a complete trace history capture of the program execution.
iSYSTEM BlueBox On-Chip Analyzer combined with the Infineon AGBT Active Probe provides a
high-speed connection to the target device using a variety of debug/trace interfaces.
Furthermore, IOM6 accessories enable the synchronous capture of analog and digital signals
in parallel to trace information. Hardware tools coupled with iSYSTEM winIDEA IDE enable
reliable recording of program flow and data trace. Integrated measurement and the
visualization tool Analyzer provides graphical presentation of execution time analysis and
much more.
Find more information on the iSYSTEM Products page or send us an email to
[e-mail].

Package content
Infineon TC377TE Compact Emulation Adapter is delivered with all components required for a
standalone operation. Adaptation package for a specific Target board must be ordered
separately.
Infineon TC377TE Compact
Emulation Adapter
with Infineon Microcontroller TC377TE
User Manual
Ordering code:
IEA-TC377TE-COMPACT
Adaptation package content
BGA Adaptation
Extender (optional)
Solder part
Refer to the Adaptation setups chapter for more information how to setup a specific
Emulation Adapter adaptation.

Operation
Device overview
The Emulation Adapter offers the following adaption setups:
· BGA
IEA-TC377TE Compact Emulation Adapter
Top / Bottom side of the Emulation Adapter
How to connect Emulation Adapter (Video Tutorial)
How to connect iSYSTEM Hardware (Video Tutorial)
Adaptation setups
BGA Adaptation

Configuration
J1: Target reset configuration
Solder jumper J1 connects the Emulation Adapter (EA) reset line and the user target board
reset line and is soldered by default.
J2: TP20_2/TESTMODEn configuration
TP20_2/TESTMODEn microcontroller pin is latched at power on reset release to enter test
mode. Alternatively, it can operate as a general purpose I/O.
Solder jumper J2 connects the Emulation Adapter (EA) TP20_2/TESTMODEn signal with the
microcontroller TP20_2 signal from the user target board. The microcontroller must not enter
test mode during the Emulation Adapter operation. The J2 jumper is by default not connected
preventing the microcontroller on the Emulation Adapter entering test mode at power on reset
if the target would be set up so. If the target uses this pin for IO operation, solder the jumper J2
and double check that the signal is properly conditioned at power on reset.
P1: AGBT
P1 connector exposes DAP and AGBT interface and has the following pinout:
Signal
Direction
Signal
Description
Signal
Pin
Pin
Signal
Signal
Description
Signal
Direction
I
AGBT TX0_P
TX0_P
1
2
Vref
Reference
Voltage
I
I
AGBT TX0_N
TX0_N
3
4
DAP0
DAP clock
O
Ground
GND
5
6
DAP1
DAP Data pin
I/O
Not Connected
NC
7
8
NC
Not Connected
Not Connected
NC
9
10
DAP2
Optional 2nd
Data pin
I/O
Ground
GND
11
12
nTRST/DAPEN
JTAG/Output
O
Not Connected
NC
13
14
CLK+
AGBT Clock
O
Not Connected
NC
15
16
CLK-
AGBT Clock
O
Ground
GND
17
18
TGO
AGBT Trigger
out
I
Not Connected
NC
19
20
AGBT ERR
AGBT Error
Not Connected
NC
21
22
RESET
Reset
I/O
22-pin ERF8 AURIX pinout
Signal Direction is described from the BlueBox perspective.
Blue color marks the trace signals.

Mechanical information
BGA292 Adaptation
BGA Adaptation: The Target can have electronic components placed around the
Microcontroller within the Emulation Adapter (EA) "ground floor", which impede
connecting the EA to the Target. In such cases the distance of the EA from the Target
can be optionally increased in steps of 3.25 mm by inserting the optional Extender. Not
more than two Extenders should be used since every connector affects signal integrity.
· With no Extender the lowest point of the EA is approx. 4.35 mm away from the
Target.
· With one Extender the lowest point of the EA is approx. 7.6 mm away from the
Target.
· With two Extenders the lowest point of the EA is approx. 10.85 mm away from the
Target.
Note that by adding the Extender or two, makes the whole setup less robust. Use
caution with Extenders to prevent breaking of the hardware setup or just part of it.
Side view of the Emulation Adapter, one Extender and
Solder part (each Extender adds approx.3,25mm)
Top view of the Solder part / Extender
Emulation Adapter
Unit (mm)
M
N
IEA-TC377TE Compact
29.1
22.4
BGA Assembly
Watch out that pin 1 position and alignment of all pins match when connecting two parts
together.
1. Mount the Solder part on the embedded target PCB.
2. If optional Extender is used, connect it to the Solder part. The Extender can also provide a
protection from damaging the Solder part if the Emulation Adapter setup is supposed to be
assembled and disassembled during the usage. In such case, it is recommended that the
Emulation Adapter is disconnected from the Extender and not from the Solder part. If the
Emulation Adapter setup needs to be disassembled, be cautious and gentle during this

procedure since all parts of the BGA assembly are very sensitive and pins can easily bent or
even break in worst case.
More Extenders can be stacked to gain height between the Emulation Adapter and the Target.
This is useful if surrounding components around the Solder part are that high that they
prevent connecting the Emulation Adapter. Keep number of Extenders at minimum since every
Extender degrades signal integrity of the electrical signals.
For ordering the correct amount of Extenders, go to the Adaptation packages content.
3. Connect the Emulation Adapter to the Solder part respectively to the Extender when it's
being used.
4. Connect iSYSTEM Debug Adapter or Active Probe to the connector on the Emulation
Adapter.
Gently press the Emulation Adapter with your thumb to the Target board and keep it stable.
With your other hand carefully align the debugger's connecting cable with the matching
connector on the Emulation Adapter. Press the cable carefully straight down until a good
connection is established.
To prevent breaking of the hardware setup or just part of it, avoid disconnecting and
connecting the hardware setup too frequently.
For more information on how to connect iSYSTEM hardware in general, refer to
isystem.com/connect.
Emulation Adapter with Debug Adapter
Extender (optional)
Solder part
Electronic circuit PCB

Accessories
To ease the development process, we recommend using the following iSYSTEM hardware tools
with the Infineon TC377TE Compact Emulation Adapter.
Ordering Code
Description
IC5700
iC5700 BlueBox On-Chip Analyzer
IC57031
IOM6 Hub (3 x FNet & FBridge)
IC57040
IOM6 CAN/LIN
IC57041
IOM6 ADIO
Active Probes
Listed Active Probes provide tracing functionality for the Infineon TC377TE Compact
Emulation Adapter.
Ordering code
Description
IC57164
Infineon AGBT Active Probe
Find more information on www.isystem.com or contact [e-mail]. To reach
for technical support, please visit www.isystem.com/support.