iSystem Infineon TC377TE User manual

Infineon TC377TE Emulation Adapter
User Manual
V1.8

This document and all documents accompanying it are copyrighted by iSYSTEM AG and all rights are
reserved. Duplication of these documents is allowed for personal use. In all other cases, written consent
from iSYSTEM is required.
iSYSTEM AG. All rights reserved.
All trademarks are property of their respective owners.
iSYSTEM is an ISO 9001 certified company.
www.isystem.com

Contents
Infineon TC377TE Emulation Adapter
Package content ...................................................................................................................................... 5
Adaptation packages ......................................................................................................................................................................................................6
Operation ................................................................................................................................................ 12
Jumper configuration ....................................................................................................................................................................................................16
Power supply package ................................................................................................................................................................................................ 21
Standalone operation ..................................................................................................................................................................................................22
IEA-TC377TE Adaptations ........................................................................................................................................................................................ 23
Mechanical information ....................................................................................................................... 25
NQPackAssembly..........................................................................................................................................................................................................27
HQPackAssembly..........................................................................................................................................................................................................28
BGA Assembly...................................................................................................................................................................................................................29
Recommended iSYSTEM tools ........................................................................................................... 30
Schematics ............................................................................................................................................. 31

Infineon TC377TE Emulation Adapter
Infineon TC377TE Emulation Adapter provides full trace capabilities for the:
· TC332 (QFP80 0.4 pitch)
· TC323, TC333 (QFP100 0.4 pitch)
· TC324, TC334 (QFP144 0.4 pitch)
· TC364 (QFP144 0.4 pitch and 0.5 pitch, )
· TC365 (QFP176 0.5 pitch)
· TC375 (QFP176 0.5 pitch)
· TC327LP, TC337LP, TC367DP, TC377TP (BGA292)
devices where trace port is not available or lacks the full trace capability.
Infineon TC377TE Emulation Adapter supports following debug and trace interfaces:
· DAP
· DAPE
· AGBT (Aurora Gigabit Trace)
The Emulation Adapter can be used as a standalone device for microcontroller evaluation
purposes or for development and test of an embedded application before the target board is
available.
iSYSTEM Debug and Trace solutions
Trace provides a non-intrusive and deep insight in the embedded application without
influencing real-time behavior. It can be used to debug the most difficult and complex code
defects and offers a complete trace history capture of the program execution.
iSYSTEM BlueBox On-Chip Analyzer combined with the:
· Infineon AGBT Active Probe or
· Infineon DAP/DAPE Active Probe or
· 10-pin 1.27mm Infineon DAP2 Wide Debug Adapter or
· 22-pin ERF8 DAP2 Debug Adapter or
· 10-pin 1.27 mm DAP Adapter via Infineon AGBT Active Probe
provides high-speed connection to the target device using a variety of debug/trace interfaces.
Furthermore, IOM6 accessories enable the synchronous capture of analog and digital signals
in parallel to trace information. Hardware tools coupled with iSYSTEM winIDEA IDE enable
reliable recording of program flow and data trace. Integrated measurement and visualization
tool Analyzer provides graphical presentation of execution time analysis and much more.
Find more information on the iSYSTEM Products page or send us an email to
[e-mail].

Package content
Infineon TC377TE Emulation Adapter is delivered with all components required for a
standalone operation. Adaptation package for specific user target board adaptation must be
ordered separately.
The IEA-TC377TE Emulation Adapter hosts Infineon emulation device TC377TE. The
emulation device will be listed on our quotation as IEA-TC377TE-MC and must be
ordered in addition to the other components. iSYSTEM solders this device and ships the
complete adapter.
Infineon TC377TE Emulation AdapterPackage
Infineon TC377TE
Emulation Adapter
Power supply package
Power converter
Power adapter
Ordering code:
IEA-TC377TE
*IEA-TC377TE-MC must be
ordered along.
Ordering code:
IEA-PS
Ordering code:
IT9V-PS
GND Wire
Crystal 20MHz
User Manual
Ordering code: BB-WIRE

Adaptation packages
Socket cover HQ Pack is used together with the production device and the Solder part
NQ Pack. For assembly instructions please refer to HQ Pack Assembly.
QFP80 Adaptation - 0.4 pitch (TC332)
80-pin
"flex” Conversion board
Connecting part
80-pin
Solder part
80-pin
Socket cover
(optional)
Ordering code:
IEA-TC377TE-TC332W
Ordering code:
IAYQPACK80SE
Ordering code:
IANQPACK80SE
Ordering code:
IAHQPACK80SE
QFP100 Adaptation - 0.4 pitch (TC323, TC333)
100-pin
"flex” Conversion board
Connecting part
100-pin
Solder part
100-pin
Socket cover
(optional)
Ordering code:
IEA-TC377TE-BTQ100W
Ordering code:
IAYQPACK100SE
Ordering code:
IANQPACK100SE
Ordering code:
IAHQPACK100SE

QFP144 Adaptation - 0.4 pitch (TC324, TC334)
144-pin
"flex” Conversion board
Connecting part
144-pin
Solder part
144-pin
Socket cover
(optional)
Ordering code:
IEA-TC377TE-TC334W
Ordering code:
IAYQPACK144SE
Ordering code:
IANQPACK144SE
Ordering code:
IAHQPACK144SE
QFP144 Adaptation - 0.4 pitch (TC364)
144-pin
"flex” Conversion board
Connecting part
144-pin
Solder part
144-pin
Socket cover
(optional)
Ordering code:
IEA-TC377TE-TC364W4
Ordering code:
IAYQPACK144SE
Ordering code:
IANQPACK144SE
Ordering code:
IAHQPACK144SE

QFP144 Adaptation - 0.5 pitch (TC364)
144-pin
"flex” Conversion board
144-pin
Solder part
Ordering code:
IEA-TC377TE-TC364W5
Ordering code:
IA144TQ-SOLDER
QFP144 Adaptation - 0.5 pitch (TC364)
144-pin
"fixed" Conversion board
144-pin
Solder part
Ordering code:
IEA-TC377TE-TC364F5
Ordering code:
IA144TQ-SOLDER

QFP176 Adaptation - 0.5 pitch (TC365)
176-pin
"flex” Conversion board
176-pin
Solder part
Ordering code:
IEA-TC377TE-TC365W5
Ordering code:
IA176TQ-SOLDER
QFP176 Adaptation - 0.5 pitch (TC365)
176-pin
"fixed" Conversion board
176-pin
Solder part
Ordering code:
IEA-TC377TE-TC365F5
Ordering code:
IA176TQ-SOLDER
QFP176 Adaptation - 0.5 pitch (TC375)
176-pin
"flex” Conversion board
176-pin
Solder part
Ordering code:
IEA-TC377TE-TC375W5
Ordering code:
IA176TQ-SOLDER

QFP176 Adaptation - 0.5 pitch (TC375)
176-pin
"fixed" Conversion board
176-pin
Solder part
Ordering code:
IEA-TC377TE-TC375F5
Ordering code:
IA176TQ-SOLDER

BGA292Adaptation (TC327LP, TC337LP, TC367DP, TC377TP)
Conversion board
Extender (optional)
Solder part
Ordering code:
IEA-TC377TE-TC377
Ordering code:
IA292LFBGA-EXTENDER
Ordering code:
IA292LFBGA-SOLDER
Target can have too high electronic components placed around the microcontroller
within the Emulation Adapter (EA) ground floor, which impede connecting the EA to the
Target. In case of the BGA292 Adaptation, the distance of the EA from the Target can
be optionally increased in steps of 3,25 mm by inserting within the Adaptation setup
the optional Extender IA292LFBGA-EXTENDER. Not more than 2 extenders should be
used since every connector affects signal integrity.
· With no Extender the lowest point of the EA is approx. 4,35 mm away from the
Target.
· With one Extender the lowest point of the EA is approx. 7,6 mm away from the
Target.
· With two Extenders the lowest point of the EA is approx. 10,85 mm away from the
Target.
Note that by adding an Extender or two, makes the whole setup less robust. Use
caution with Extenders to prevent breaking of the hardware setup or just part of it.
Measurement Board (optional)
Measurement Board
Ordering code:
IAMTC377TE

Operation
Device overview
A setup in conjunction with the User target board and Wire adapter contains:
Power supply
IEA-PS
IT9V-PS
iSYSTEM BlueBox connecting to the
Emulation Adapter
Emulation
Adapter
IEA-TC377TE
IEA-TC377TE-MC must be
ordered along
Measurement
Board (optional)
IAMTC377TE
Conversion board
with 20 cm cable
IEA-TC377TE-TC332W or
IEA-TC377TE-BTQ100W or
IEA-TC377TE-TC334W or
IEA-TC377TE-TC364W4 or
IEA-TC377TE-TC364W5 or
IEA-TC377TE-TC365W5 or
IEA-TC377TE-TC375W5
Connecting part
IAYQPACK80SE
IAYQPACK100SE or
IAYQPACK144SE or
IAYQPACK144
Solder part
IANQPACK100SE or
IANQPACK144SE or
IANQPACK144 or
User target board
Emulation Adapter connection scheme with Wire adapter

A setup in conjunction with the User target board and "fixed" Conversion board contains:
Power supply
IEA-PS
IT9V-PS
iSYSTEM BlueBox connecting to the
Emulation Adapter
Emulation
Adapter
IEA-TC377TE
IEA-TC377TE-MC must be
ordered along
Measurement
Board (optional)
IAMTC377TE
Conversion board
IEA-TC377TE-TC364F5
IEA-TC377TE-TC365F5
IEA-TC377TE-TC375F5
Solder part
IA176TQ-SOLDER or
IA144TQ-SOLDER
User target board
Emulation Adapter connection scheme with "fixed" Conversion board

A setup in conjunction with the BGA292 Adaptation board solution and the User target board
contains:
Power supply
IEA-PS
IT9V-PS
iSYSTEM BlueBox connecting to the
Emulation Adapter
Emulation
Adapter
IEA-TC377TE
IEA-TC377TE-MC must be
ordered along.
Measurement
Board (optional)
IAMTC377TE
Conversion board
IEA-TC377TE-TC377
Extender
(optional)
IA292LFBGA-EXTENDER
For ordering the correct
amount of Extenders go to
the IEA-TC377TE Adaptations
chapter.
Solder part
IA292LFBGA-SOLDER
User target board
Emulation Adapter connection scheme with BGA292 Adaptation

Power supply package, which is delivered with the Emulation Adapter, is required when:
· The Emulation Adapter is used as a standalone device
· User target doesn’t provide accurate supply voltage
· User target doesn’t provide sufficient current for the Emulation Adapter operation.
IEA-TC377TE Emulation Adapter
Top / Bottom side of the Emulation Adapter

Jumper configuration
J1: Target reset configuration
Jumper J1 connects the Emulation Adapter reset line and the user target board reset line and
is populated by default. Emulation Adapter also features a Reset push button (SW1).
If having problems establishing the initial debug session with the Emulation Adapter, remove
J1 and try again.
J2 and J3: Clock source configuration
Jumpers J2 and J3 select clock source for the emulation device.
Position 1-2 (default position) selects the crystal circuit oscillator on
the user target board.
Position 2-3 selects an external clock source (Q1 socket on the
Emulation Adapter).
The Emulation Adapter may not operate when user target board’s crystal circuit is used
as the clock source. Typical design guideline is that the crystal should be as close as
possible to the microcontroller. The crystal on the user target board might not oscillate
in conjunction with the Emulation Adapter when the clock lines (TP21_2, TP21_3)
between the crystal and the emulation device on the Emulation Adapter become too
long, thus affecting the impedance of the crystal circuit.
Enclosed in the Emulation Adapter package is a separately packed 20 MHz crystal. The
crystal can be used as a 20MHz external clock (XOSC) source to the emulation device.
If a different clock frequency is required, insert appropriate crystal into the Q1 socket
and replace C7 (default 10pF populated) and C8 (default 10pF populated)
accordingly.
Crystal socket Q1 is per default not populated (NP).

Crystal socket Q1 schematics below:
J4 & J5: GND connection points
In case a good ground connection is required, connection points bridge J4 and pin J5 provide
easy access to the emulation adapter GND potential.
J6 & J7: VFLEX & VAREF
VFLEX - If the target’s VFLEX pin isn’t exposed, set the jumper to the position J6 to connect
VEXT from the target to power VFLEX.

Setting the jumper when emulating the BGA device may brick the emulation or the target
device.
VAREF - If the target’s VAREF2 pin isn’t exposed, set the jumper to the position J7 to connect
VAREF1 from the target to power VARE2
Setting the jumper if VAREF2 is present on the device may brick the emulation or the
target device.
P1: DAP
P1 connector exposes DAP debug interface and has the following pinout:
Signal
Direction
Signal
Description
Signal
Pin
Pin
Signal
Signal
Description
Signal
Direction
I
Reference
Voltage
Vref
1
2
DAP1
DAP Data pin
I/O
Ground
GND
3
4
DAP0
DAP clock
O
Ground
GND
5
6
DAP2
Optional 2nd
Data pin
I/O
Not Connected
NC
7
8
DAPEN
Output
O
Ground
GND
9
10
nRESET
Reset
I/O
10-pin Infineon DAP pinout
Signal Direction is described from the BlueBox perspective.
iSYSTEM BlueBox solution supporting Infineon DAP debug interface connects to the P1
connector.
P2: Power supply configuration
Emulation Adapter Power supply is configured via the unshrouded 26-pin 2.54 mm header
(P2).
Signal direction
Signal
Pin
Pin
Signal
Signal direction
User target board
TVEXT
1
2
VEXT
Emulation device
User target board
TVDDM
3
4
VDDM
Emulation device
User target board
TVAREF1
5
6
VAREF1
Emulation device
User target board
TVAREF2
7
8
VAREF2
Emulation device
User target board
TVEVRSB
9
10
VEVRSB
Emulation device
User target board
TVFLEX
11
12
VFLEX
Emulation device
Not connected
NC
13
14
NC
Not connected
Not connected
NC
15
16
NC
Not connected
Not connected
NC
17
18
NC
Not connected
Not connected
NC
19
20
NC
Not connected
Ground
GND
21
22
GND
Ground
Ground
GND
23
24
GND
Ground
Ground
GND
25
26
KEY
P2 Signal description

By default, all jumpers are set to connect user target power supply to the microcontroller
residing on the Emulation Adapter. Only pins 1-2, 3-4, 5-6, 7-8, 9-10 and 11-12 must be bridged
but for the convenience and ease of use all jumpers are set, except for pins 25-26.
Pin 26 is the polarizer key preventing incorrect connection of the IEA-PS Power converter, when
being plugged in.
If a different power source is used (e.g., a Standalone operation), remove all jumpers and apply
3V3 or 5V to:
· TVEXT (pin 1),
· TVDDM (pin 3),
· TVAREF1 (pin 5),
· TVAREF2 (pin 7),
· TVEVRSB (pin 9),
· TVFLEX (pin 11).
Enclosed Power supply package (Power converter and Power adapter) simply plugs into the
P2 header row, providing the necessary power supply for Emulation Adapter operation. LED1
indicates, if power is supplied to the Emulation Adapter.
Refer to the microcontroller documentation for more details about power voltage designations.
P8: DAPE
P8 connector exposes DAPE debug interface and has the following pinout:
Signal
Direction
Signal
Description
Signal
Pin
Pin
Signal
Signal
Description
Signal
Direction
I
Reference
Voltage
Vref
1
2
DAPE1
DAP Data pin
I/O
Ground
GND
3
4
DAPE0
DAP clock
O
Ground
GND
5
6
DAPE2
Optional 2nd
Data pin
I/O
Not Connected
NC
7
8
DAPEN/DAP3
Output
I/O
Ground
GND
9
10
NC
Not Connected
10-pin DAPE pinout
Signal Direction is described from the BlueBox perspective.
iSYSTEM BlueBox supporting Infineon DAPE debug and trace interface connects to the P8
connector.

P7: AGBT
P7 connector exposes AGBT interface and has the following pinout:
Signal
Direction
Signal
Description
Signal
Pin
Pin
Signal
Signal
Description
Signal
Direction
I
AGBT TX0_P
TX0_P
1
2
Vref
Reference
Voltage
I
I
AGBT TX0_N
TX0_N
3
4
DAP0
DAP clock
O
Ground
GND
5
6
DAP1
DAP Data pin
I/O
Not Connected
NC
7
8
NC
Not Connected
Not Connected
NC
9
10
DAP2
Optional 2nd
Data pin
I/O
Ground
GND
11
12
nTRST/DAPEN
JTAG/Output
O
Not Connected
NC
13
14
CLK+
AGBT Clock
O
Not Connected
NC
15
16
CLK-
AGBT Clock
O
Ground
GND
17
18
TGO*
AGBT Trigger
out
I
Not Connected
NC
19
20
AGBT ERR
AGBT Error
Not Connected
NC
21
22
RESET
Reset
I/O
22-pin AGBT pinout (Revision C1)
Signal Direction is described from the BlueBox perspective.
Blue color marks the trace signals.
* Pin 18: TGO (AGBT Trigger out) is connected to the pin TP32.6. Before Revision C1 pin 18 was
NC (Not Connected).
iSYSTEM BlueBox solution supporting AGBT (Aurora GigaBit Trace) interface connects to the
P7 connector.