iTero Element 5D User manual

Laptop
configuration
operation
manual

iTero Element 5D laptop configuration operation manual English
i
Copyright
© 2018 Align Technology, Inc. All Rights Reserved.
The information contained in this manual is subject to change
without notice.
The hardware and software described in this document are supplied
under a Sales and Services Agreement and may be used only in
accordance with the terms of that agreement.
No part of this document may be reproduced, photocopied, stored
in a retrieval system, or transmitted in any manner (electronic or
mechanical) for any purpose other than the customer’s normal
usage, without the prior written permission of Align Technology Inc.
This operational manual describes the iTero®Element 5D laptop
configuration Optical Impression Device. English language version.
Updated October 2018.
Trademarks
The following are trademarks and/or service marks of Align
Technology, Inc. or one of its subsidiaries or aliated companies
and may be registered in the U.S. and/or other countries: Align
Technology Inc., iTero®
Any other trademarks or registered trademarks appearing in this
document are the property of their respective owners.
USA oce
Corporate Headquarters
Align Technology, Inc.
2820 Orchard Parkway
San Jose, California 95134
www.aligntech.com
Tel: [phone]
Fax: [phone]
Israel oce
Align Technology Ltd.
3 Ariel Sharon Boulevard
Or-Yehuda 6037606
Israel
Tel: [phone]
Fax: [phone]
Netherlands oce
International Headquarters
Align Technology B.V.
Arlandaweg 161
1043 HS Amsterdam
Tel: [phone]
Fax: [phone]
Customer support
Tel: [phone]
E-mail:
[e-mail]
E-mail:
[email protected]
Obelis s.a.
Boulevard Général Wahis 53
B - 1030 Brussels, Belgium
www.obelis.net
Tel: [phone]
Fax: [phone]
E-mail: [email protected]

ii
iTero Element 5D laptop configuration operation manual English
Class 1 laser compliance
This device complies with: “21 CFR 1040.10” and “EN 60825-1”.
CSA compliance
This device complies with the following CSA standard for Canada
and the USA:
“UL Std No. 60601-1 – Medical Electrical Equipment Part 1: General
Requirements for Safety”
FCC compliance
This device complies with Part 15 of FCC Rules and its operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
FCC warning
Modifications to the device that are not expressly approved by the
manufacturer may void your authority to operate the device under
FCC Rules.
EMC compliance
This device complies with the following EMC standard:
“IEC 60601-1-2 Medical electrical equipment - Part 1-2: General
requirements for basic safety and essential performance - Collateral
standard: Electromagnetic phenomena - Requirements and tests”.
Safety compliance
This device complies with the following safety standard:
“IEC 60601-1 Medical electrical equipment –Part 1: General
requirements for basic safety and essential performance.”
CE compliance
This device complies with Council Directive 93/42/EEC for Medical
Devices.
Class 1 Laser Product
C US

iii
Manuel d’utilisation de iTero Element 5D laptop configuration Français
Conformité laser de classe 1
Cet appareil est conforme aux normes: «21 CFR 1040.10» et
«EN60825-1».
Conformité CSA
Cet appareil est conforme à la norme CSA suivante pour le Canada
et les États-Unis:
«Norme UL 60601-1 - Appareils électriques médicaux -
Premièrepartie: Règles générales de sécurité»
C US
Conformité FCC
Cet équipement est conforme à la section 15 des règles la FCC.
Sonfonctionnement est soumis aux deux conditions suivantes:
1. Cet appareil ne doit causer aucune interférence nuisible.
2. Cet appareil doit accepter toute interférence reçue, y compris des
interférences pouvant provoquer un fonctionnement non désiré.
Avertissement de la FCC
Les modifications apportées à l'appareil qui ne sont pas
expressément approuvées par le fabricant peuvent révoquer votre
droit d'utiliser l'appareil en vertu des règles de la FCC.
Conformité CEM
Cet appareil est conforme à la norme CEM suivante:
«IEC 60601-1-2:2007 Equipement médical électrique - Section 1-2:
Exigences générales pour la sécurité de base et les performances
essentielles - Norme collatérale: Electromagnétisme - Exigences et
essais».
Conformité aux normes de sécurité
Cet appareil est conforme à la norme de sécurité suivante:
«IEC 60601-1: Appareils électriques médicaux – Section 1:
Exigences générales pour la sécurité de base et les performances
essentielles.»
Conformité CE
Cet appareil est conforme à la directive du Conseil Européen 93/42
relative aux dispositifs médicaux.
Produit laser de classe 1

iv
iTero Element 5D laptop configuration operation manual English
Indicates the temperature limits to which the
medical device can be safely exposed.
Indicates the need for the user to consult the
instructions for use.
Manufacturer’s batch code.
Indicates the range of atmospheric pressure to
which the medical device can be safely exposed.
Indicates the range of humidity to which the
medical device can be safely exposed.
Fragile, handle with care.
This side should be up.
IEC 60417-5031: Direct current.
Wand (scanning unit).
USB socket.
Electric battery.
RoHS (China).
IEC 60417-5009: STAND-BY.
CAUTION: DO NOT step on the 5D laptop
configuration hub
Wherever this symbol appears on the device, it
is recommended to refer to this document for
information on proper usage of the device.
Applied part type BF. Any component on which
this symbol appears is electric isolation type BF.
Separate collection of electrical waste and
electronic equipment is required.
Attention: This symbol is used to highlight the fact
that there are specific warnings or precautions
associated with the device. Wherever this symbol
appears on the device, it is mandatory to refer to
safety-related information within this document.
Parts or accessories on which this symbol occurs
should not be reused.
CAUTION: US Federal Law restricts this device
to sale by or on the order of a licensed Dentist,
Orthodontist or Dental Professional. The system
serves as a prescription medical device and
should be operated by qualified health-care
providers only.
Medical device manufacturer.
Order number.
Serial number.
Indicates the Authorized representative in the
European Community.
IEC 60417-5032: Alternating current.
Indicates a medical device that needs to be
protected from moisture.
Symbols
The following symbols may appear on iTero Element 5D hardware
components, and may also appear within this document and other
iTero Element 5D literature.
"Rx only"
REF
SN
MLot

v
Manuel d’utilisation de iTero Element 5D laptop configuration Français
Symboles
Les symboles suivants peuvent apparaître sur les composants
matériels iTero Element 5D, ainsi que dans ce document et dans
d’autres documents relatifs à iTero Element 5D.
Indique les limites de température auxquelles
le dispositif médical peut être exposé en toute
sécurité.
Indique le besoin pour l'utilisateur de consulter les
instructions d'utilisation.
Numéro de lot de fabrication.
Indique la plage de pression atmosphérique à
laquelle le dispositif médical peut être exposé en
toute sécurité.
Indique la plage d'humidité à laquelle le dispositif
médical peut être exposé en toute sécurité.
Fragile, à manipuler avec soin.
Ce côté doit être placé vers le haut.
IEC 60417-5031: Courant continu.
Tige (unité de numérisation).
Prise USB.
Batterie électrique.
RoHS (Chine).
IEC 60417-5009: EN ATTENTE.
ATTENTION: NE PAS marcher sur le hub de
configuration pour ordinateur portable 5D
MLot
Partout où ce symbole apparaît sur l'appareil, il
est recommandé de consulter ce document pour
obtenir des informations sur sa bonne utilisation.
Partie appliquée de type BF Tout composant sur
lequel ce symbole apparaît contient une isolation
électrique électrique de type BF.
Une collecte séparée des déchets électriques et
des équipements électroniques est requise.
Attention: Ce symbole est utilisé pour souligner
le fait que des avertissements ou des précautions
spécifiques sont associés à l'appareil. Partout où
ce symbole apparaît sur l'appareil, il est obligatoire
de se référer aux informations relatives à la
sécurité contenues dans ce document.
Les pièces ou accessoires sur lesquels ce
symbole apparaît ne doivent pas être réutilisés.
MISE EN GARDE: la loi fédérale américaine limite
la vente de cet appareil par ou pour lecompte d'un
dentiste, d'un orthodontiste ou d'unprofessionnel
dentaire agréé. Le système constitue un dispositif
médical sur ordonnance et nedoit être manipulé
que par des prestataires desoins de santé qualifiés.
Fabricant de dispositif médical.
Numéro de commande.
Numéro de série.
Indique le Représentant agréé dans la
communauté européenne.
IEC 60417-5032: Courant alternatif.
Indique un dispositif médical qui doit être protégé
de l'humidité.
"Rx uniquement"
REF
N° de série

vi
iTero Element 5D laptop configuration operation manual English
Safety instructions
Before beginning to work with the system, all users are required to
read these safety instructions.
Power supply
Power is supplied to the system via an internal medical grade
power supply.
Electric warning
• Electric shock hazard! Only authorized Align Technology
technicians can remove external panels and covers. There are no
user-serviceable parts inside.
• To avoid risk of electric shock, iTero Element 5D laptop
configuration must only be connected to a supply mains with
protective grounding.
• Connect the 5D laptop configuration hub device only to a laptop
that is approved according to IEC60950, and to UL60950-1.
Laptop and all its accessories shall be located at least 1.5m away
from the patient. Do not scan a patient and touch the laptop or
any of its accessories at the same time.
• Only the Align Technology scanning unit and the approved
laptop should be connected to the USB sockets on the 5D laptop
configuration hub.
• Only the Align Technology approved power cable should be used
to connect the 5D laptop configuration hub with the AC outlet.
Safety classifications
• Type of protection against electrical shock: Class 1.
• Degree of protection against electrical shock: Type BF.
• Degree of protection against harmful ingress of water: Ordinary.
• Equipment not suitable for use in presence of flammable
anesthetic mixtures.
• Mode of operation: Continuous.
Prescription health device
The system serves as a prescription medical device and should be
operated by qualified health-care providers only.
Scanner warnings
• The scanner emits red laser light (680nm Class 1) as well as white
LED emissions, and 850nm LED emissions. Normal usage of the
scanner does not present any danger to the human eye. However,
doctors should refrain from shining the scanner directly into the
patient’s eyes.
• Avoid twisting cable, knotting cable, pulling on cable, stepping
on cable.
• When the system is not in use, the scanning unit should be placed
inside the cradle with the probe facing towards the cart’s post and
rear side of the touch screen so there will be no eye contact with
the laser beam or the flickering white LED emission, and 850nm
LED emissions in any case.
• The doctor should activate scanning operation only while the
scanner’s probe is inside the patient’s mouth.
• Doctors should avoid placing the scanner in the cradle while
scanning operation is still active.
• If scanner malfunction occurs, stop scanning and call
service support.
Cleaning & disinfection
• To avoid cross contamination, it is mandatory that after each
patient session the disposable plastic sleeve be replaced and the
scanning unit be disinfected.
• To avoid cross contamination, it is mandatory that after each
patient session the gloves shall be removed and replaced.
• To avoid cross contamination discard gloves when torn,
contaminated, or removed for any reason.
• Dispose of scanner sleeves according to standard operating
procedures or local regulations for the disposal of contaminated
medical waste.
Unpacking & installing
The system should be unpacked and installed following Align
Technology’s instructions.
Work environment
• The system should be moved between rooms with utmost care to
avoid damage.
• WARNING: Do not block the air vents on the Scanning Unit and
Base Unit.
• WARNING: System is intended for indoor use only. It should not be
exposed to direct sunlight, excessive heat or humidity.
• The system should only be used following operating temperatures
as defined in Appendix B.
• If iTero Element 5D laptop configuration has just been brought
into the oce from a hot or cold or humid environment, it should
be set aside until it has adjusted to the room temperature to avoid
internal condensation.
Electro magnetic interference
WARNING: This device has been tested and found to comply with the
requirements for medical devices according to standard IEC60601-
1-2. This standard is designed to provide reasonable protection
against harmful interference in a typical medical installation.
However, because of the proliferation of radio-frequency transmitting
equipment and other sources of electrical noise in the healthcare
environments (e.g., cellular phones, mobile two-way radios, electrical
appliances), it is possible that high levels of such interference due
to close proximity or strength of source, may result in disruption of
performance of this device.
ESD may cause an interference during scanning. In case of ESD
interference the system will stop scanning / displaying proper
viewfinder image. If the failure occurs within scan, the user may be
required to press the wand scan button to restart the scan. The
viewfinder will always recover automatically.
General
WARNING: No modification of this equipment is allowed.

vii
Manuel d’utilisation de iTero Element 5D laptop configuration Français
Consignes de sécurité
Avant de commencer à travailler avec le système, tous les utilisateurs
doivent prendre connaissance de ces consignes de sécurité.
Alimentation électrique
Le système est alimenté via une alimentation interne de qualité
médicale.
Avertissement électrique
• Risque de choc électrique! Seuls les techniciens agréés par Align
Technology peuvent retirer les panneaux et les capots externes.
L'appareil ne contient aucune pièce réparable par l'utilisateur.
• Pour éviter tout risque d'électrocution, le iTero Element 5D laptop
configuration doit uniquement être connecté à une prise de courant
avec une prise terre de protection.
• Connectez le dispositif de hub de configuration pour ordinateur
portable 5D uniquement à un ordinateur portable respectant les
normes IEC60950 et UL60950-1. L'ordinateur portable et tous ses
accessoires doivent être situés à au moins 1,5 m du patient. Ne
scannez pas un patient et ne touchez pas l'ordinateur portable ou
l'un de ses accessoires en même temps.
• Seule l'unité de numérisation Align Technology et l'ordinateur
portable approuvé doivent être connectés aux prises USB du hub
de configuration pour ordinateur portable5D.
• Seul le câble d'alimentation approuvé par Align Technology doit
être utilisé pour connecter le hub de configuration pour ordinateur
portable 5D à la prise de courant.
Classifications de sécurité
• Type de protection contre les chocs électriques: Classe 1.
• Degré de protection contre les chocs électriques: Type BF.
• Degré de protection contre les infiltrations d’eau nuisibles:
Ordinaire.
• L'équipement ne convient pas à une utilisation en présence de
mélanges anesthésiques inflammables.
• Mode de fonctionnement: En continu.
Dispositif médical sur ordonnance
Le système constitue un dispositif médical sur ordonnance et nedoit
être manipulé que par des prestataires desoins de santé qualifiés.
Avertissements liés au scanner
• Le scanner émet une lumière laser rouge (680nm de classe 1), ainsi
que des émissions à LED blanches et des émissions à LED de 850
nm. L'utilisation normale du scanner ne présente aucun danger
pour l'œil humain. Cependant, les médecins doivent éviter de placer
le scanner directement dans les yeux du patient.
• Évitez de tordre le câble, de nouer le câble, de tirer sur le câble, de
marcher sur le câble.
• Lorsque le système n'est pas utilisé, l'unité de numérisation doit
être placée à l'intérieur du socle avec la sonde orientée vers la
colonne verticale du chariot et du côté arrière de l'écran tactile afin
d'éviter tout contact visuel avec le faisceau laser ou l'émission de
LED blanche environnante et des émissions de LED de 850 nm
dans tous les cas.
• Le médecin ne doit activer l’opération de numérisation que lorsque
la sonde du scanner est dans la bouche du patient.
• Les médecins doivent éviter de placer le scanner dans le socle tant
que l'opération de numérisation est encore active.
• En cas de dysfonctionnement du scanner, arrêtez la numérisation
et appelez le support technique.
Nettoyage et désinfection
• Pour éviter toute contamination croisée, il est obligatoire de
remplacer le manchon en plastique à usage unique après chaque
séance avec un patient et de désinfecter l’unité de numérisation.
• Pour éviter toute contamination croisée, il est obligatoire de retirer
et de remplacer les gants après chaque séance avec un patient.
• Pour éviter toute contamination croisée, jetez les gants déchirés,
contaminés ou retirés pour une raison quelconque.
• Jetez les manchons du scanner conformément aux procédures
d'utilisation standard ou aux réglementations locales relatives à
l'élimination des déchets médicaux contaminés.
Déballage et installation
Le système doit être déballé et installé conformément aux instructions
fournies par Align Technology.
Environnement de travail
• Le système doit être déplacé d'une pièce à l'autre avec le plus
grand soin pour ne pas l'endommager.
• AVERTISSEMENT: Ne bloquez pas les fentes d'aération de l'unité
de numérisation et de l'unité de base.
• AVERTISSEMENT: Le système est conçu pour une utilisation en
intérieur uniquement. Il ne doit pas être exposé aux rayons directs
du soleil, à une chaleur excessive ou à l'humidité.
• Le système ne doit être utilisé qu'aux températures de
fonctionnement définies dans l'annexe B.
• Si le iTero Element 5D laptop configuration vient juste d'être
amenée dans le bureau en provenance d'un environnement chaud,
froid ou humide, laissez le matériel s'adapter à la température de la
pièce pour éviter la condensation interne.
Interférence électro-magnétique
AVERTISSEMENT: Cet appareil a été testé et approuvé conforme
aux exigences des dispositifs médicaux selon la norme--IEC6060112.
Cette norme est conçue pour fournir une protection raisonnable
contre les interférences nuisibles dans une installation médicale
classique. Toutefois, en raison de la prolifération des équipements
de transmisssion sur fréquence radio et d'autres sources de bruit
électrique dans les environnements de soins de santé (par exemple,
téléphones portables, radios mobiles bidirectionnelles, appareils
électriques), il est possible que des niveaux élevés d'interférences
dus à la proximité ou à la force d'une source puissent entraîner des
perturbations de fonctionnement de cet appareil.
Les DES (décharges électrostatiques) peuvent provoquer des
interférences lors de la numérisation. En cas d'interférence DES, le
système s'arrêtera de numériser ou d'acher la bonne image dans
le viseur. Si la défaillance se produit pendant l’analyse, il peut être
demandé à l’utilisateur d’appuyer sur un bouton spécifique pour
relancer l’analyse. Le viseur se réinitialisera toujours automatiquement.
Informations générales
AVERTISSEMENT: Aucune modification de cet équipement n'est
autorisée.

1
iTero Element 5D laptop configuration operation manual English
Table of contents
Chapter 1: Introduction 2
About this document 2
Intended use / indication for use 2
Benefits of the iTero Element 5D laptop configuration system 2
The iTero Element 5D laptop configuration user interface 3
Chapter 2: Basic hardware features 4
Front view of system 4
Scanning unit (wand) 5
Mobile system packaging (for transport) 6
Chapter 3: Assembly instructions 7
Step 1: Assembly 7
Step 2: Download iTero Element 5D laptop configuration software 8
Step 3: Make it Mine process 9
Chapter 4: Operating instructions 10
Web cam 10
Chapter 5: Scanner handling, cleaning, and disinfection instructions 11
Handling of the scanning unit (wand) 11
Handling of the scanning unit cable 11
Cleaning the scanning unit 11
Disinfecting the scanning unit 11
Chapter 6: Changing sleeves between patients 12
Replacing disposable sleeves 12
Scanner sleeves 13
Chapter 7: Clinic LAN network guidelines 14
Introduction 14
Preparations 15
Router guidelines 15
Internet connection guidelines 15
Firewall 15
Wi-Fi tips 15
Appendix A: EMC declaration 16
Appendix B: System specifications 17

iTero Element 5D laptop configuration operation manual English
2
Chapter 1:
Introduction
About this operation manual
The iTero Element 5D laptop configuration system is delivered as a
proprietary, laptop based workstation for performing intra-oral scans
in the doctor’s oce. This operational manual describes how to start
and shut down the system, how to correctly handle the Scanning
Unit/Wand and cable, and how to clean the Scanning Unit and
replace its sleeves between patients.
Intended use / indication for use
The iTero Element 5D laptop configuration is an intra-oral scanner
with the following features and intended/indicated for use:
1. The optical impression (CAD/CAM) feature of iTero Element 5D
laptop configuration is intended/indicated for use to record the
topographical images of teeth and oral tissue. Data generated from
iTero may be used in conjunction with the production of dental
devices (e.g., aligners, braces, appliances, etc.) and accessories.
2. iTero Element 5D laptop configuration software is used with the
iTero scanner in capturing 3D digital impressions of teeth, oral
soft tissue and structures, and bite relationship. iTero software
controls the processing of the data, facilitating the integration of
data, and exporting of the data for CAD/CAM fabrication of dental
restorations, orthodontic devices, abutments, and accessories. In
addition to scan data, various patient and case information can
be imported/exported or used for simulation purposes. Other
functions are available for verification and service of the system
and to serve as an order management tool.
3. The Element 5D laptop configuration NIRI functionality, is a
diagnostic aid for the detection of interproximal caries lesions
above the gingiva and for monitoring the progress of such lesions.
Benefits of the iTero Element 5D laptop configuration
system
The iTero Element 5D laptop configuration system provides
important advantages over existing crown-production methods,
including powder-free scanning, greater crown-production accuracy,
and immediate feedback during the scanning process.
Refer to our website www.itero.com to learn how the iTero Service
can enhance your business by increasing patient satisfaction,
improving clinical outcomes, and enhancing oce eciency.
Software installation instructions
Please consult the list of approved laptops and approved Antivirus
applications at www.iTero.com.
To ensure optimal performance use of the iTero application, only
approved laptops must be used with the iTero Element 5D laptop
configuration system.

3
iTero Element 5D laptop configuration operation manual English
The iTero Element 5D laptop configuration user interface
The iTero Element 5D laptop configuration system provides an
intuitive user interface for performing digital scans for Restorative
or Orthodontic use. The doctor is guided through the scanning
sequence by means of visual and text assistance. The laptop’s
touch screen and the wand buttons are used to respond to screen
instructions during the scanning process.
Tap to enter the Learning Center or start training
Tap anywhere on
screen to close this
help overlay
(Tap to start a new case) (Tap to see/search patient list)
Tap to lock the desktop
Tap to set your preferences Double tap to connect to a support
agent for remote troubleshooting
(please call support first)
Tap to view notifications,
updates and other messages
from Align Technology
Tap to check the
status of your orders
Laptop battery level
One tap on the question mark will enable a transparent Help
overlay that will provide a brief overview. Please note that the
Headset image appears instead of the question mark while in
this view. Tap anywhere to close the help screen and return
to the relevant screen.

iTero Element 5D laptop configuration operation manual English
4
Chapter 2:
Basic hardware features
Front view of the system
Laptop with touch screen
Flex hub
Wand and cradle

5
iTero Element 5D laptop configuration operation manual English
Scanning unit (wand)
Touchpad
Disposable sleeve
Detachable scanning
unit cable with
USB connector
Side buttons: Scan, on/o,
touchpad activation
Air vents

iTero Element 5D laptop configuration operation manual English
6
Mobile system packaging (for transport)
Transportation
Use the supplied case to move the system between oces.
Moving the system
To ensure maximum system protection, it is recommended to move
the system with care. Follow these instructions for relocating the
system:
1. Attach the blue protective sleeve onto the wand.
2. Verify the scanning unit (wand) sits well inside the case.
3. Unplug the 5D laptop configuration hub and laptop AC power
cables from the wall outlet.
4. Place all items in the case (see picture above).
5. Make sure the case is kept dry to protect the system components
from humidity.

7
iTero Element 5D laptop configuration operation manual English
Chapter 3:
Assembly and software installation
Step 1: Assembly
Please follow the instructions below to assemble your iTero
Element 5D laptop configuration scanner:
3.
Connect USB cable to the hub
6.
Plug the hub power cord into the AC
power outlet
1.
Place the wand in the cradle
4.
Connect USB cable to the laptop
2.
Connect hub power cord to the hub
5.
Connect wand cable to the hub
Hub and hub power cord
Cradle
Wand and wand cable
USB cable to connect laptop and hub
A
B
C
DA
B
C
D
Wand
(scanning unit)
AC power USB port
Two important notes:
• The hub must be connected to
an AC wall outlet at all times
• The laptop should be connected
to an AC wall outlet for intraoral
scanning

iTero Element 5D laptop configuration operation manual English
8
USB port
Step 2: Download iTero Element 5D laptop
configuration software
For proper software installation and configuration of your iTero
Element 5D laptop configuration scanner, please ensure your iTero
wand is secure in the cradle and connected to the hub, and the hub
is connected to the laptop. Please make sure your laptop is plugged
into the AC wall socket during the entire software installation.
1. Laptop setup
A. Turn on the laptop.
B. Update the Windows to the latest version.
2. iTero software download
A. Open the registered email inbox in the browser. Look for the
email “Your iTero was shipped” which includes instructions.
B. Click on the link to get to the page with software downloads.
or
C. Alternatively, open the browser and go to (type the address
into your browser) download.itero5D.com.
3. iTero software installation
A. Click on the “Get started” button.
B. Run the downloaded installation file.
C. Follow the instructions on the screen to complete the
download of the iTero software.
It is highly recommended to regularly check for Windows updates
and install them. Please enable updates.
It is also recommended to exit to Windows and shut down the
computer at the end of each day to allow updates to install.
Before installing the iTero Element 5D software for the first
time, please install all available Windows updates. New Windows
computers should apply updates automatically.
To check for Windows Updates, open “Settings”(Windows key
+ I), choose “Update & Security”, and then “Windows Update”.
Click“Check for updates”to see if there are new updates available.
It is recommended to close other software programs while
using the iTero Element 5D laptop configuration system
for scanning.

9
iTero Element 5D laptop configuration operation manual English
Step 3: Make it Mine process
1.
Select language of preference and tap on the Make it Mine button to
start the Wizard.
2.
Follow the Wizard instructions on the screen to complete the
customization of the iTero Element 5D.

iTero Element 5D laptop configuration operation manual English
10
Chapter 4:
Operating instructions
Make sure the laptop is connected to an AC wall outlet, to ensure
the battery level does not reach its low battery status, at which time
scanning will no longer be possible.
Power up the laptop to start iTero program.
It is recommended to keep the system in operation during oce
hours to allow background file transfers between the doctor’s oce,
the doctor’s partnered labs, and the Align Technology Center. It is
recommended to shut down the system at the end of the day, and to
reboot in the morning.
Web cam
Connect the web cam to the laptop following the
product instructions.

11
iTero Element 5D laptop configuration operation manual English
Chapter 5:
Scanner handling, cleaning,
and disinfection instructions
Handling of the scanning unit (wand)
The scanning unit contains delicate components and should be
handled with care.
Handling of the scanning unit cable
• The scanner cable should be treated with care to avoid
possible damage.
• Between patient sessions, it is recommended to undo any twists
and knots in order to relieve all tension from the scanner cable.
The scanning unit requires proper cleaning & disinfection before first
use and before each additional use, and no later than 30 minutes
after the last scan.
Cleaning and disinfecting the scanning unit
The scanning unit (wand) should be cleaned and disinfected
as follows:
• Soak a lint free cloth in ready to use CaviCide 1, and squeeze until
the cloth is moist.
• Wipe the wand thoroughly to remove gross debris.
• The entire device needs to be visually inspected to ensure that no
residual or debris remains prior to continuing to the next step.
• Soak two additional lint free cloths in Cavicide 1, and squeeze
until the cloth is moist. Then wipe the device thoroughly, ensuring
with special care that all the surfaces, to all edges and slots, are
covered. Contact time will be at least 2 minutes.
• Then wet lint free cloths with distilled water and wipe all surfaces
for at least 15-30 seconds.
• Then use dry lint free cloths to dry the surfaces.
Maintenance
The industrial camera is maintenance-free.