ITT Neo-Dyn 801P5 User manual

N EO -D YN

801P5 S MART S WITCH
TM
INSTALLATION AND
OPERATION MANUAL
PN 610-0002 Rev D
ECO 71349

801P5 Smart Switch
TM
Page i
WARNING
CAUTION
NOTE
Manual No. 610 0002 Rev. D
Neo Dyn
28150 Industry Drive
Valencia, CA 91355
Tel: [phone]
Fax: [phone]
World Wide Web: www.neodyn.com
Copyright 2002
ITT Industries
Important Information
The product warranty applicable to this ITT Neo Dyn
®
instrument
is as stated on page 41 of this manual.
Should any after delivery problems arise, please contact
ITT Neo Dyn’s Customer Service using the information above.
Our normal business hours are weekdays, 7:00 am to 3:30 pm,
Pacific Time.
Before installing the Smart Switch
TM
, become familiar with the
installation instructions in Chapter 2.
Indicates a hazard which can cause severe personal injury,
death, or substantial property damage if the warning is
ignored.
Indicates a hazard which will or can cause minor personal injury
or property damage if the caution is ignored.
Indicates additional information about a particular item necessary
to the operation of the unit.
This document contains proprietary information which is the
property of Neo Dyn, a unit of ITT Industries. This document
may not be reproduced, either in part or in full, without the
consent of ITT Industries.

Page ii Installation and Operation Manual
TABLE OF CONTENTS
PAGE
CHAPTER 1 INTRODUCTION................................................. 1
ABOUT THIS MANUAL......................................................... 4
KEYS ........................................................................................ 4
DISPLAY.................................................................................. 4
CUSTOMER SERVICE............................................................ 4
CHAPTER 2 INSTALLATION.................................................. 5
MOUNTING ............................................................................. 5
PRESSURE CONNECTION .................................................... 5
ELECTRICAL CONNECTIONS ............................................. 6
CHAPTER 3 OPERATION & PROGRAMMING ................... 11
OPERATION MODE.............................................................. 11
FRONT PANEL CONTROLS................................................ 12
INPUT CONTROLS ............................................................... 13
DISPLAYING PRESSURE .................................................... 13
DISPLAYING SET POINTS.................................................. 14
STANDARD VS. WINDOW MODE..................................... 15
PROGRAMMING MODE...................................................... 17
ENTER PROGRAMMING MODE ........................................ 17
CHANGING THE SET POINTS............................................ 19
ADDITIONAL FEATURES................................................... 20
CHAPTER 4 ANALOG OPTION............................................. 25
ANALOG OPTION WIRING................................................. 25
TURNING ANALOG OUTPUT ON AND OFF(LOOP)...... 25
4 20 MILLIAMPERE OUTPUT CALIBRATION (4CAL)... 26
4 20 MILLIAMPERE OUTPUT SCALING .......................... 27
CHAPTER 5 TROUBLESHOOTING ...................................... 29
ERROR MESSAGES.............................................................. 29

801P5 Smart Switch
TM
Page iii
TABLE OF CONTENTS
PAGE
CHAPTER 6 SERIAL COMMUNICATIONS (Z Option) .......35
GENERAL ..................................................................................35
WIRING ......................................................................................35
CHAPTER 7 SPECIFICATIONS..............................................37
STANDARD ...........................................................................37
OPTIONS ................................................................................40
WARRANTY INFORMATION .................................................41

Page 1 801P5 Smart Switch
TM
CHAPTER
1
INTRODUCTION
The Neo Dyn
®
801P5 Smart Switch
TM
is a solid state pressure
switch designed for a wide range of applications in pneumatic and
hydraulic systems up to 3,000 psig. Pressure indication, switch
status and operational status are continually displayed on the front
panel. The unit can be configured to display pressure readings in a
variety of formats.
The Smart Switch
TM
can be configured on site, using the front
panel keypad and 4 digit display, or remotely via the optional
RS 232 connection. The 4 20 mA output option offers remote
monitoring capabilities.
A built in password security system prevents unauthorized
adjustments. When locked, pressure can be monitored and set
points may be viewed, but no adjustments can be made without
entering the correct password.
The Smart Switch
TM
may be ordered to operate on 115 VAC
50/60 Hz, 230 VAC 50/60 Hz, or 18 30 VDC input power.
The external configuration of the Smart Switch
TM
is shown in
Figure 1 on the next page.

Page 2 Installation and Operation Manual
Figure 1 Model 8 1P5 Smart-Switch
TM
(Mounting Brackets not Shown)
Conduit
Connection
1/2-14 NPT
Pressure
Port
1/4-18 NPT
Std
4-20 mA
Out ut
RS232
COM Port
18” free leads
#22 AWG
Status
Indicators
Key ad

Page 3 801P5 Smart Switch
TM
The standard electrical interface is 22 AWG free leads exiting
from a ½” 14 NPT male conduit connection. The standard
pressure connection is ¼” 18 NPT female; a 7/16” 20 SAE
pressure connection is available as Option E.
Output options available for the Smart Switch
TM
include a
4 20 mA analog output (Option V), scalable display units
(Option Q), and RS232 communications (Option Z).
The RS232 option can be used to configure and monitor the unit
remotely. This option includes Windows
®
based software.
Chapter 7 on page 37 contains complete specifications for the
801P5 Smart Switch
TM
.

Page 4 Installation and Operation Manual
ABOUT THIS MANUAL
The following paragraphs describe the format conventions used in
this manual.
KEYS
Most of the instructions contain directions to press a key, which is
one of the blue touchpads on the display surface of the
Smart Switch
TM
. When included in instructions, the keys are
shown in brackets, as [STORE].
DISPLAY
When shown in the text, the LED displays are formatted as
279.3.
CUSTOMER SERVICE
If you have any questions about the 801P5 Smart Switch
TM
that
are not covered in this manual, you can contact Neo Dyn in several
ways:
The customer service phone number is [phone]. Our
customer service department is open from 7:00 am to 3:30
p.m. Pacific Time.
Our Internet site is: www.neodyn.com.

Page 5 801P5 Smart Switch
TM
WARNING
WARNING
WARNING
WARNING
CAUTION
CHAPTER
2
INSTALLATION
Installation of the Smart Switch
TM
is relatively straightforward.
However, the Smart Switch
TM
must be installed by a qualified
electrician, in compliance with all local and national electrical codes.
Electrical Hazard
Do not make electrical connections while power is on.
Always check for multiple circuits.
Always make sure grounding is adequate.
MOUNTING
The Smart Switch
TM
can be mounted directly to the pressure
connection, or it can be attached to a flat surface, such as a wall,
near the connection to be monitored. For surface mounting, slide
the two mounting brackets into the slots on the back of the
Smart Switc
TM
and use #10 (.190 in. dia.) fasteners.
PRESSURE CONNECTION
The standard pressure connection for the 801P5 Smart Switch
TM
is a ¼” 18 NPT female pipe thread. A 7/16” 20 SAE boss is
also available as Option E. When installing the Smart Switch
TM
,
always:
• Make sure that the unit and your system have the same fittings.
• Use the wrench flats provided.
• Seal all joints with pipe joint sealing compound.
Avoid excessive torque on all threaded connections.

Page 6 Installation and Operation Manual
ELECTRICAL CONNECTIONS
Units are supplied with 22 AWG free leads exiting from a ½” 14
NPT male conduit connection. The leads are color coded and
marked. See Figure 2 for AC operation and Figure 3 for DC
operation.
4 20 mA output (option letter V) is connected to the 2 pin
connector on the top right of the unit per Figure 4, using the
supplied mating connector. This mating connector has solder cups
that will take wires as large as #18 AWG. See Chapter 4 for
operating instructions.
The RS232 communications (option letter Z) are connected to the
3 pin connector on the top left of the unit (See Figure 5), using
the supplied mating connector. This mating connector has solder
cups that will take wires as large as #18 AWG. Cable length must
not exceed 50 feet. See Chapter 6 for operating instructions.
All field wiring for the 801P5 must comply with requirements of
the NEC or applicable local electrical codes.

Page 7 801P5 Smart Switch
TM
Figure 2 - Schematic for AC Operation

Page 8 Installation and Operation Manual
Figure 3 - Schematic for DC Operation

Page 9 801P5 Smart Switch
TM
Figure 4 - Wiring for 4-2 mA Analog Output
A
B
+ 4-20 Ma
RETURN

Page 10 Installation and Operation Manual
Figure 5 - Wiring for RS-232 Communications
A
B
DATA SEND
SIGNAL GROUND
DATA RECEIVE
C

Page 11 801P5 Smart Switch
TM
CHAPTER
3
OPERATION & PROGRAMMING
This section describes the regular (normal) operation of the
Smart Switch
TM
as it monitors pressure after installation and
initial setup, and the Programming Mode for changing the
settings.
Both modes rely on the front panel for information and input. See
Figure 6 on the next page.
OPERATION MODE
To begin operation, apply correct power to the appropriate free
leads (there is no on off switch).
In normal operation mode, the display shows:
• Online LED (green) indicates operation mode
• S1 and S2 LED's (red) indicate the switch status (illuminated
when the relay coil is energized or the solid state switch is
actuated)
• System pressure is displayed
You can also check the set points in operating mode; all other
actions are done in programming mode. However, If you have the
RS232 option, you can program the unit remotely using its
Windows
®
software on a personal computer; see Chapter 6.

Page 12 Installation and Operation Manual
FRONT PANEL CONTROLS
Figure 6 The Front Panel,
with Function Keys Below the Display
Indicators
Display
The display shows the actual system pressure in normal
operation.
S1 and S2 (Switch) Indicators
The S1 and S2 (red LED's) indicate switch status (illuminated
with the relay coil energized or the solid state switch actuated).
Online Indicator
The Online indicator (green LED) is lit when the unit is
online and active. If the indicator is not lit, the unit is offline.

Page 13 801P5 Smart Switch
TM
NOTE
INPUT CONTROLS
S1 and S2 INCR/DECR
Push the [S1] and [S2] [INCR] and [DECR] keys to see what
values the set points are configured for.
MENU
Use the [MENU] key to enter program mode.
UP/DOWN ARROW
The [UP DOWN ARROW] keys are used to move through
the list of submenus.
SELECT
The [SELECT] key is used to move into the desired submenu.
STORE
The [STORE] key is used to temporarily save changes made
to the current submenu and return to the main menu.
RUN
The [RUN] key is used to lock in the programming changes
made.
After pressing [RUN], to return to operation mode (go back
online), you must press [SELECT]. Otherwise, any programming
changes will be lost after 2 minutes.
DISPLAYING PRESSURE
When the Smart Switch
TM
is in operation mode, system pressure
is displayed on the front panel.

Page 14 Installation and Operation Manual
NOTE
DISPLAYING SET POINTS.
Programmed set points can be viewed on the front panel display
by pressing the corresponding [S1] or [S2] key. To view the
increasing value for Switch 1, press [S1 INCR]. To view the
decreasing value for Switch 2, press [S2 DECR].
Figure 7 Press the Incr / Decr Buttons
to Display Set Points for S1 / S2
After 5 seconds of keypad inactivity, the display automatically
changes back to the system pressure display. While viewing set
points, the output functions remain active.

Page 15 801P5 Smart Switch
TM
STANDARD VS. WINDOW MODE
The terms “Standard” and “Window” describe two methods for
setting up the Smart Switch
TM
to monitor pressure.
Standard Mode
In Standard Mode, illustrated in Figure 8, the SP1i (or SP2i) set
point actuates when the pressure being monitored goes above the
set value. At this point, the Smart Switch
TM
might turn off
whatever electrical power is being applied to a pump, for
example, which is increasing or maintaining the pressure. The
switch de actuates, or resets, when the pressure drops below the
preset decreasing set point (SP1d or SP2d). At this time, the
electrical power to the pump would be turned back on.
Figure 8 Standard Mode
INCREASING SET POINT
DECREASING SET POINT
DEADBAND
SWITCH
DEACTUATES
SWITCH
ACTUATES

Page 16 Installation and Operation Manual
Deadband
The deadband is the separation between the increasing set point
and the decreasing set point, as shown in Figure 8. The deadband
can be anywhere from 1% to 99% of Full Scale Output (F.S.O.).
In the case above where the Smart Switch
TM
is controlling a
pump, a wider deadband reduces the frequency at which the pump
cycles on and off.
Window Mode
This mode is useful when you want to maintain pressure within a
certain range, and want to be notified when pressure either goes
above or falls below that range. In Window Mode, the Smart
Switch® starts out actuated, then deactuates when it reaches its
lower set point (SP1d or SP2d). As pressure continues to
increase, the switch actuates again when it reaches the upper
set point (SP1i or SP2i). This range between the lower and upper
set points is the "window". When pressure decreases, the
sequence reverses, with a deadband of 1% of F.S.O. at each of the
set points. See Figure 9.
In this mode, the Smart Switch
TM
might be wired to, say, an alarm
bell, which would sound if the pressure either rose above SP1i or
fell below SP1d.
Figure 9 Window Mode
WINDOW
UPPER BOUNDARY
(INCREASING SET POINT)
LOWER BOUNDARY
(DECREASING SET POINT)
NO = OPEN
NO = CLOSED
NO = CLOSED