Iwata Tech Genius Pro GP-01 User manual

Quick Start Guide of
IWATA Genius Pro
正确处理本产品
废弃电器和电子设备
左边符号表明根据当地的法律和法规，
您的产品和/或其电池必须和家庭垃圾分
开处理。当此产品的使用寿命到了尽头
时，请将它送至当地管理部门指定的收
集点。处理您的产品和/或其电池时，分
开收集和回收将有助于节约自然资源，
并确保回收是以保护人类健康和环境的
方式进行的。
注意事项
请勿拆卸或改装本产品。
请勿将本产品浸水或投入火中。
请勿撞击或使用重物敲打本产品。
在使用本产品过程中可能出现发热的现象，属于正常现
象。使用时请保证本产品有充足的散热空间。
请勿将本产品暴露于温度和湿度剧烈变动的环境中。
在使用非本产品配套的数据线进行充电时，可能出现由
于线材的差异导致充电时间加长。
Model : GP-01

Thank you for purchasing Genius IWATA
Genius Pro.
Please read this Quick Start Guide carefully
before use, and please keep it for future
reference after reading.
1. Color temperature range: 2600K-6000K (±100K)
2. Color Rendering Index: CRI≥97 TLCI≥99
3. LED Bulbs Quantity: 144
4. Rated Output Power: 16W
5. Turbo Output Power: 24W
6. Beam Angle: 120 °
7. Illuminance (at a distance of 0.3 m):
7500lx@6000K, 6500lx@2600K
8. Built-in lithium battery capacity: 4700mAh
9. Battery life:
about 1 hour at 100% power output
about 17 hours at 5% level of power output
10. Input Voltage and Current:
5V/1A, 5V/2.4A,
9V/2A,
12V/1.5A,
15V/1.2A (for quick charging or charging while in use)
11. Display Screen: OLED screen
12. Dimension: 160 mm× 88mm × 16mm (6.3" ×3.46" × 0.63")
13. Weight: 350g
14. Bottom Screw Hole: 1/4"
15. Allowable Temperature Range:
-5~35°C (no dew or frosting) for working
0~35°C (no dew) for charging
-20~60°C for storage
Specifications
01

Illumination Diagrams
02 03
Layout of GP-01
Charger Port
Turbo/ON/OFF Button
Display Screen
Power Switch
Brightness
Adjustment Dial
Color Temperature
Adjustment Dial
Package Contents
Genius Pro, Light Diffuser, USB Charging Cable, Hot Shoe
Bracket, Quick Start Guide.
Quick Start Guide of
IWATA Genius Pro
Model : GP-01

04 05
Turning ON/OFF the light and Turbo Mode
When the power switch is on,
1. Tap the ON/OFF Button to turn the light on/off.
2. Press the ON/OFF Button harder to switch to Turbo
Mode.
The maximum time length for using turbo mode is 90
seconds each time. When you start, the “T” icon and the
available time will be displayed on the screen. When Turbo
mode is turned on, the system starts counting down. It will
be automatically turned off when Turbo time runs out.
If the temperature warning occurs, the Turbo mode will stop
and the process bar of time be set to zero.
Remaining Time for Turbo Mode
Progress bar
Turbo Mode
(Turbo Button)
To turn the power on: Slide the power switch to " ";
To turn the power off : Slide the power switch to "".
To adjust the brightness: Rotate the dial.
The adjustment range is between 5%~100%.
To rotate the dial slowly will adjust up/down 5%. While to
rotate it rapidly will adjust up/down 10% level of brightness.
To adjust the color temperature: Rotate the dial.
The color temperature can be adjusted within the range of
2600K~6000K.
To rotate the dial slowly will adjust up/down 50K, while to
rotate it rapidly will have 150K value of change.
Instructions
1. Turing on/off the power
2. Brightness and Color Temperature Adjustment
Current Brightness
Current Color Temperature

② Screen Rotation Lock: Genius Pro has an automatic
rotary screen and the current screen orientation can also be
locked.
③ Groups: When wireless communication (requiring
external wireless module) or wired communication (requiring
dedicated connection cable be linked for each working
units) is applied, the lights in the same channel can be
grouped and linked, and the group can be set from A to F.
④ Communication Channel: When wireless communication
or wired communication is applied, only devices in the same
channel can communicate. The channels can be set from 0
to 9.
Press the ON/OFF Button again to exit the parameter setting
interface.
Other Settings
① Automatic Shutdown: The system standby time can be set
as: 1m, 5m, 10m, 30m, and 60m (“m” for minute). If no
operation is proceeded, when the power is on, Genius Pro
will shut itself down after preset standby time.
Standby Time ①
Radio Module Groups ③
Radio Module Channels ④
Screen Lock ②
Indicator ⑤
Press and hold the ON/OFF Button and turn the dial
simultaneously, to enter the parameter setting interface.
The Indicator will be displayed on the screen.
Rotate the dial to switch between Radio Module Groups
and Radio Module Channels settings.
Rotate the dial to adjust the parameters, at which the
indicator points accordingly.
The setting includes: standby time, screen rotation lock,
groups and communication channel:
06 07

Temperature Warning
The low temperature warning icon appears when ambient
temperature is below the lowest allowable temperature.
Genius Pro may not work properly under this circumstance.
The high temperature warning icon appears when the
temperature of the product is above the highest allowable
temperature. If temperature keeps rising, Genius Pro will be
automatically switched off. The high temperature warning
icon will disappear, when the temperature of the product
returns to normal.
The warning signal for
Low working temperature
The warning signal for
High working temperature
Icon displayed for the Battery
① This icon is displayed, when the external power supply is
connected. When quick charge is applied, there will be a
thunderbolt mark.
② It shows the predicted time required for being fully
charged (“m” for minute and “h” for hour). When full
charging is completed, “OK” icon will be displayed.
③ Remaining Battery time: The icon shows the estimated
remaining time of battery charge ("m" for minute and "h" for
hour). When the remaining time is shorter than 5 minutes,
the icon will flash once in every 2 seconds.
④ icon comes out, when Genius Pro is working,
connected to a 5V/1A charger or a charging cable of low
quality. It is recommended to use a 9V/2A charger and the
original charging cable.
Power Input Icon ①
Remaining time of full charging ②
Remaining Battery Capacity
Battery remaining time ③
Insufficent Power Supply ④
08 09

Use of the Light Diffuser
(Installation with Magnets)
Put the diffuser on the surface of front side
of Genius Pro, make them cling to each
other. Hold the diffuser disc and stretch it
outward to create when you use it.
Press the disc inward until it clings to the
front side or take the disc off after using.
Battery
When the battery of Genius Pro is fully charged, please
detach Genius Pro from the USB cable.
Please do not charge the battery, when the ambient
temperature is beyond the allowable range, otherwise
Genius Pro can be damaged or battery life can be
shortened.
The battery may gradually run down and not be switched
on properly, if the product is long-term unused. Please
recharge the battery in this circumstance and recharge the
battery at least once three months.
If the battery capacity indicator has an error in displaying
the actual capacity, please fully discharge and recharge
the battery to correct it.
The Rechargeable battery has a limited service life and
should only be replaced by the manufacturer. When the
performance of battery is obviously decreased after years,
please contact the local distributor.
Wireless Receiver Access
Wireless Device Access: When a wireless receiver is
connected or wired communication access is created to
Genius Pro, the device group and channel signals will be
displayed, and the specified group and channel can be set
in the parameter interface.
Note: Channels and groups will be only displayed when
connected to a wireless receiver or wired communication.
Access of the Wireless Device
10 11

型号: GP-01
IWATA Genius Pro
快速使用手册
Disposal Information
The symbol on the left indicates that
according to local laws and regulations this
product and its battery shall not be
disposed as household waste. When this
product reaches its end of life, take it to a
collection point designated by local
authorities. The separate collection and
recycling of your product and/or its battery
at the time of disposal will help conserve
natural resources and prevent potential
n e ga t iv e c o n s e q u e n c e s f o r t he
environment and human health.
Precautions
Do not disassemble or modify this product.
Do not immerse the product in water or put it into fire.
Avoid any dash or knock on this product.
Genius Pro’s temperature can increase, when it works.
Please make room for heat dissipation.
Do not expose this product to extreme changes in
temperature and humidity.
If this product is charged with a non-original cable,
charging time may increase due to the difference in wire.
12 13

产品规格
包装内容
使用时-5~35℃ (无结露、无结霜)
(无结露)充电时0~35℃
存储时-20~60℃
14 15
感谢您选择使用IWATA Genius Pro摄影灯，请在
使用前仔细阅读本使用指南，阅读后请保留以便
日后参考。
1．色温范围：2600K-6000K（±100K）
2．显色性：CRI≥97 TLCI≥99
3．LED灯珠数量：144
4．额定输出功率：16W
5．Turbo输出功率：24W
6．发光角度：120℃
7．光照度(相距0.3米)：7500lx@6000K，6500lx@2600K
8．内置锂电池容量：4700mAh
9. 电池续航时间：
100%功率输出约为1小时，5%功率输出约为17小时
10. 充电电源：5V/1A、5V/2.4A
9V/2A、12V/1.5A、15V/1.2A（快充或边充边用）
11. 显示屏：OLED点阵屏
12. 产品尺寸：160mm×88mm×16mm
13. 产品重量：350g
14. 固定接口：通用1/4螺孔
15. 温度许可范围：
光照度示意图
Genius Pro补光灯、柔光配件、USB充电线、热靴支架、
说明书。
型号: GP-01
IWATA Genius Pro
快速使用手册

操作说明
将电源开关拨动到“ ”位置即可打开电源；
将电源开关拨动到“ ”位置即可关闭电源。
1．打开/关闭电源
2．亮度及色温调节
旋转带有 标志的转盘用于调节亮度，调节范围为
5%~100%，慢速转动步进为5%，快速转动步进为10%。
旋转带有 标志的转盘用于调节色温，调节范围为
2600K~6000K。慢速转动步进为50K，快速转动步进
为150K。
Genius Pro设备部位图
按键
电源开关
亮度调节
色温调节
充电接口
显示屏
开灯、关灯与Turbo模式
Turbo模式可用时间：启动Turbo模式每次最大使用时间为
90S，且会根据使用情况自动计算可用时间。当Turbo模式
开启后，系统开始倒计时，计时结束后自动退出Turbo模
式。当出现低温或高温警告则不允许开启Turbo模式，且进
度条与时间归0。
当前亮度值
当前色温值
Turbo模式
Turbo模式可用时间
进度条
轻按按键可进行开关灯，重按按键可进入或退出Turbo模式。
16 17