Iwiss KG1096 User manual

KG-1096 RATCHETING PEX CLAMP CINCH TOOL
One master cinch tool installs all sizes from 3/8" to 1" of Cinch Clamps.
With a unique “tab” design, the Cinch Tool goes into those hard-to-reach spaces.
Ratchet design releases only when the cinch clamp tab is properly pinched, thus ensuring a leak-proof connection.
Meets ASTM F-2098 specifications.
Compresses Stainless Steel Clamp Rings to secure PEX or PE-RT tubing to brass or poly crimp fittings.
WARNING! This product contains chemicals including DEHP, which is known to the State of California to cause
cancer and birth defects or other reproductive harm. Wash hands after handling. For more information, go to
www.P65Warnings.ca.gov.
OPERATION
1. Cut PEX tubing squarely, leaving a clean, even
edge. Remove burrs.
2.Slide PEX cinch clamp over tubing and insert
fitting. Place cinch damp l/8"-l/4
3.Place PEX cinch clampnub between tool jaws
and ratchet the clamp until the PEX Cinch Clamp
Tool auto-releases.
4. Pressure test the PEX tubing and inspect before
normal use. If there are any signs of leaks,
repeat the total procedure.
1/8"to1/4"
FEATURES
NOTE: Do not use with Zurn Quickclamp PEX crimp PEX crimp rings.
RTM
SPECS
Tubing Compatibility: PEX
Fitting System Compatibility: clamp
Application:
Type:
3/8"PEX
1/2"PEX
5/8"PEX
3/4"PEX
1"PEX
TOOL
CALIBRATION MODEL NO:KG1096
KG-1096 RATCHETING PEX CLAMP CINCH TOOL
ECCENTRICSTUD
RORATE COUNTER-CLOCKWISE
TO INCREASE JAW GAP
ADJUSTMENTNUT
IN THE EVENT OF A JAW
COMPRESS HANDLES TO
RELIEVE PRESSURE ON
RATCHET PULL RELE
ASELEVER
IN DIRCTION OF ARROW
Do not use this tool to remove the clamps. Any use other
than installation will void any and all warranties.
Clean tool periodical l y to remove rust and di rt.
Lubricate all parts after cleaning to provide a light
protective coating of oil.
If tool operate becomes sluggish at any time, lubricate
prior to further use.
Attention:
Do not use the Cinch Tool if it has been damaged,
as this may result in an improper cinch. After
repeated use of the Cinch Tool, it may require
calibration. For convenience, a calibration gauge
is provided in the tool box..
CLOSE HANDLE
TO STOP POINT
INSERT GAGE
INTO JAW GAP
GAGE MUST
STOP AT NO-GO
IF GAGE GOES
BEYOND THIS POINT
RE-CALIBRATE TOOL
NO-GO
GAGE
HOW TO REMOVE
1.loosen adjustment nut. 2.place go portion of gauge
into jaw gap.
3.rotate ec centric stud
counter-clockwise until
jaws contact gage.
4.tighten nut. 5. check tool with gauge
the first and last crimp
on each job site.

IF IT’S IWISS, IT’S SECUREIF IT’S IWISS, IT’S SECUREIF IT’S IWISS, IT’S SECURE
Purchase the right toolis the key factor when tacking a large PEX project.
Find what you will need from our wide selection of PEX tools.
WATER HEATER SOLUTION REPIPE PROGRAMNEW CONSTRUCTION
F1807 COPPER RING CRIMP TOOL
When connections are done properly, this should be a relatively last and
inexpensive way of connecting PEX. There are a variety of different
tools and crimp-ring manufacturers, and these products are relatively
easy to purchase at a variety of retailers. The tools are generally one
size fits all, so a 1/2-inch connection and a 1-inch connection can be
made with no adjustment to the tool.
Benefits of PEX Clamp
IWS-FAS
1/2",3/4",1"
IWS-FA
1/2’’, 3/4’’, 1’’
IWS-1234W
1/2’’,3/4’’
IWS-C
1/2",3/4"
F877 STAINLESS STEEL RING/V-GROOVED RING PRESS TOOL
IWS-1S
1"
IWS-34S
3/4"
IWS-12S
1/2"
IWS-S1234
1/2",3/4"
F2098 CLAMP RING CINCH TOOL
KG1096-K
3/8" TO 1"
KG-1096
3/8" TO 1"
BJ0010C
3/8" TO 1"
F1960 EXPANSION RING EXPANDING TOOL
IWS-F1960MC
3/8", 1/2",3/4", 1"
IWS-F1960
1/2", 3/4", 1"