J.Burrows BRIGHTON MB JBBRIMSHBK User manual

Weight capacity: 120kgs
1 CTN
This design and instruction booklet is subject to copyright.
www.officeworks.com.au
For spare parts or hardware call [phone] or email [email protected]
ASSEMBLY INSTRUCTIONS
BRIGHTON MB MESH CHAIR
JBBRIMSHBK / JBBRIMSHWE

[phone]
20min
•Please check you have all hardware before assembly.
•If you are missing any hardware, please contact Kyvas on [phone] or
email [email protected]
•Please ensure you have the name of the item, required hardware part and quantity.
•Please retain your receipt as proof of purchase to validate your warranty.
NOTE
• Do not tighten screws before all screws are in the right place.
• Do not use this product unless all bolts, screws and knobs are firmly secured.
• Check that all bolts, screws and knobs are securely tightened at least every 4 months.
CAUTION
• If parts are missing, broken, damaged or worn stop using the product until all repairs
are made using manufacturer authorised parts.
• Failure to follow these warnings could result in serious injury.
WARNING
• CHILDREN MUST BE SUPERVISED.
Officeworks Ltd. | 236-262 East Boundary Road | Bentleigh East VIC 3165 | AUSTRALIA
DANGER
2/11

If you are missing any parts or hardware call [phone] or email [email protected]
3/11
H
x1 x1
x5x1 x1 x1
x1 x2
C
LR
M6
J
x 4x 1
I
6x30mm
K
x 4
6x25mm 6x25mm
x 4
LM
x 4

Note: Push the castors (H) firmly into hole at the end of each leg.
Note: Turn the Star Base (G) upright and insert Gas Lift (E) into the center hole of Star Base (G).
Place cover (F) over the Gas Lift (E).
F
E
H
G
G
4/11

Note: Attach Armrests (C) to the Seat Cushion (B) using 4xScrews (I) with Allen Key (M).
Fully tighten the screws with Allen Key (M).
Note: Attached Armrests (C) to the Backrest (A) using 4xScrews (J) .
Do not tighten Screws fully until you have completed assembly.
5/11
I
4 Pcs
used to complete
this step.
ø6x30mm
M
I
C-R
B
C-L
FRONT
M
A
J
C-L C-R
J
4 Pcs
used to complete
this step.
ø6x25mm

Note: using 4xPlug (L) to cover the Armrests (C) Screw hole.
Note: Align the Seat Plate (D) so the FRONT of the Seat Plate matches the FRONT
label on the bottom of the Seat Cushion (B) . Fully tighten the screws with Allen Key (M).
L
L
C-L C-R
6/11
6M
K
B
D
FRONT
K
4 Pcs
used to complete
this step.
ø6x25mm

Your Brighton MB Mesh Chair is now complete and ready for use.
IMPORTANT NOTE: Periodically check and re-tighten screws.
8
Note: Place assembled seat on the Gas Lift (E). Push down firmly until connection is secure.
7
7/11
E

Thank you for your purchase. Please retain your receipt to validate warranty.
If you would like to know more about our furniture products, please visit www.officeworks.com.au
8/11
• Spot clean mesh/fabric with upholstery shampoo or dry cleaning powder only.
• Do not saturate mesh/fabric. Apply proprietary cleaning products strictly according
to instructions. Wipe dry immediately with an absorbent dry cloth.
• Treat spills on PU material immediately with an absorbent cloth by blotting the spill.
• Do not use detergents, solvents or abrasive cleaners.
Care Instructions
• Keep away and protect from direct sunlight and heat.
• Avoid contact with skin, in particular during high temperatures and humidity.
• Clean, check and tighten all parts regularly.
• Vacuum regularly.

BRIGHTON MB MESH CHAIR
Chair Functionality
Chair Tilt
-Pull lever out to unlock & allow
chair to tilt back & forth.
-Push lever to lock. Chair will have slight
movement in locked position.
9/11
- To increase chair height pull
lever upward while lifting body
weight slightly off the seat.
- Release lever at desired height.
- To lower chair height sit fully into
the chair and pull lever upward.
- Release lever at desired height.
Your feet should be resting flat on
the floor.

BRIGHTON MB MESH CHAIR
Chair Functionality
10/11
Adjustable Lumbar Support
-To adjust lumbar support up or down,
sit in the chair and reach behind with both
hands,raise or lower support to required
comfort level.