J.S. Technology HDMI to YUV/YPbPr User manual

WARNING!
The HDMI to YUV & L/R Audio converter is supplied with a 230V mains adaptor.
All normal precautions should be observed towards electronics devices. Do not
spill any liquids on the unit or power supply. Do not attempt to service the unit.
Do not cover the unit, do allow for ventilation. Do not spray the unit with any com-
bustible substances.
In the unlikely event the unit falters for any reason, disconnect from the mains
supply and retry after a few minutes. Contact information is provided below.
Input:
1x HDMI at 480i/576i/480p/576p/720p/1080i/1080p.
Up to 1.65Gpbs / 165MHz, HDMI 1.2.
Output:
1x YUV/YPbPr at 480i/576i/480p/576p/720p/1080i/1080p.
Vertical frequency range of 50/60Hz.
Left and Right stereo audio.
Power:
Supplied with a 5V 2A power supply.
Power consumption maximum 5W
Dimensions:
88 x 26 x 75mm.
Technical Specification.
J.S. Technology Ltd.,
APL Centre,
Stevenston Ind. Est.,
Stevenston.
Ayrshire
KA20 3LR
© 2010.
E-mail: [e-mail] Tel: [phone] Fax: [phone]
HDMI to YUV (YPbPr) & L/R Audio Converter.
http://www.js-technology.com
Instruction Manual.
 Converts HDMI to a YUV / YPbPr Compoent type connection.
 Auto set up—no user intervention required.
 Ideal for Projectors / Plasma TVs / LCD TVs with no HDMI input.
 Up to 1080p Full HD supported.
 Stereo Audio output.
 Easy to use.
It is recommended that good quality leads be used with the converter. Suitable cables
are available from J.S. Technology as well as most good retailers. The unit requires 5V
DC supply to operate, a suitable mains adaptor is provided.
2010.
Manual printed in UK/Europe.
Input
Output

HDMI to YUV & L/R Audio Converter.
The HDMI to YUV & L/R Audio Converter is the ideal means to add an HDMI
connection to a display which offers a YUV / YPbPr / Component type input. Via the
converter it is possible to add an HD TV connection to displays and systems which are not
able to accept the HDMI connector.
The converter has only one input connection, the HDMI input. Typical sources are:
 Blu Ray Player.
 DVD player.
 Sky HD.
 Virgin Media.
 Freeview.
 Games Consoles.
Output from the converter is via three phono connections for the YUV / YPbPr
Component video and two phonos for Left / Right audio. The YUV should be connected
directly to the intended display. The display will automatically detect the presence of the
converted picture and should display this. Adjustments of position and size may be
required.
Audio for Left and Right can be connected to the display or to an external amplifier. If
the external amplifier supports surround sound then a direct connection from the source
via a digital audio feed is preferable.
A typical connection scheme is shown in the page opposite.
During installation ensure that all devices are switched off. Then:
1. Connect the HDMI from the source to the converter.
2. Using a component lead from the converter connect to the display.
3. Connect the power supply to the converter (DC / 5V) and then to the mains supply.
4. Power up source and display, selecting appropriate input for the display.
Some older CRT displays may only be able to operate on the standard definition
interlaced modes (480i, or 576i) and the source must be set accordingly. Not all displays
will be able to operate as high as 1080p and the source in these case should not be run
higher than 720p. The converter fully support all these rates and resolutions.
Connection to the HDMI to YUV Converter.
Figure above: Connection of the HDMI to YUV & L/R Audio Converter.
Power supply and audio amplification omitted for clarity.