Jøtul C 24 IT User manual

Jøtul C 24 IT
UK - Installation and Operating Instructions 2
IT - Manuale di installazione ed uso 18
Jøtul C 24 IT
Manual Version P02
I manuali inclusi con il prodotto vanno conservati per l’intera durata di vita del prodotto.
Sostituire le Istruzioni di istallazione e di utilizzo con questo
manuale.

2
Table of contents
1.0 Regulatory information .............................. 2
2.0 Technical data .......................................... 2
3.0 Safety ........................................................ 6
4.0 Installation ................................................ 6
5.0 Daily use ................................................. 14
6.0 Servicing ................................................. 15
7.0 Maintenance............................................ 16
8.0 Optional Equipment ................................ 16
9.0 Recycling................................................. 17
10.0 Warranty.................................................. 17
On all our products there is a label
indicating the serial number and
year. Write this number in the
place indicated in the installation
instructions.
Always quote this serial number when
contacting your retailer or Jøtul.
les combustibles recommandés.
Respectez les consignes d'utilisation. Utilisez uniquement
Verwenden Sie nur empfohlenen Brennstoen.
Montage- und Bedienungsanleitung beachten.
Follow user`s instructions. Use only recommended fuels.
standard
Certicate/
The appliance can be used in a shared ue.
Minimum distance to adjacent combustible materials:
Emission of CO in combustion products
Lot no: Y-xxxx, Year: 200x
Manufacturer:
N-1602 Fredrikstad
Norway
Jøtul AS
POB 1441
Sweden
EUR Intermittent
Nominal heat output
Norway
Country
Operational type
Fuel type
Operation range
Eciency
Klasse II
Classication
Standard
Flue gas temperature
Room heater red by solid fuel
Product:
Jøtul
SP Sveriges Provnings- och
221546
Forskningsinstitut AB
SP Swedish National
Testing and Research
Institute
:
Approved by
:
:
:
:
:
:
:
Minimum distance to adjacent combustible materials:
OGC
SP
EN
Lot no. Pin.
1.0 Regulatory information
Installation of a fireplace must be according to local codes and
regulations in each country.
All local regulations, including those that refer to national and
European standards, shall be complied with when installing
the product.
The installation can only be taken into use after it has been
checked by a qualified inspector.
An approval label made of heat resistant material is located
on the heat shield at the back of the product. This contains
information about identification and documentation for the
product.
2.0 Technical data
Material: Cast iron
Finish: Black paint
Type of fuel: Wood
Max. log length: 50 cm
Smoke outlet: Top
Flue pipe dimension: Ø 150 mm
Outside air connector: Flexible aluminium pipe
Ø80 mm/Ø100 mm
Weight: Approx. 172 kg
Optional extras: Frame wide, Fan, Outside
air connection kit Ø 100
mm.
Product dimensions, distances: See Fig. 1
Technical data in accordance with 13229:
Nominal heat output: 9.0 kW
Flue gas flow rate: 6.5 g/s
Recommended chimney draught: 12 Pa
Efficiency: 85.3%@9.0 kW
CO emissions (13% O2): 0.06%
OGC emissions (13% O2) 48 mg/Nm3
Dust emissions 11 mg/Nm3
Flue gas temperature: 213°C
Operation: Intermittent
Intermittent operation means normal use of a fireplace. This
means that to refuel the fire, you add more wood as soon as
the previous load of wood has burned down to embers.
ENGLISH

3
Jøtul C 24 IT inclusive optional wide frame
Fig. 1A
900167-P01
ENGLISH

4
Jøtul C24 IT inclusive optional narrow frame
Fig. 1B
900167-P01
ENGLISH

5
Fig. 2
900167-P01
ENGLISH

6
3.0 Safety
NB! To guarantee optimal performance and safety, Jøtul
stoves must be fitted by a qualified installer.
Any modifications to the product by the distributor, installer or
consumer may result in the product and safety features not
functioning as intended. The same applies to the installation of
accessories or optional extras not supplied by Jøtul. This may
also be the case if parts that are essential to the functioning and
safety of the fireplace have been disassembled or removed.
In all these cases, the manufacturer is not responsible or liable
for the product and the right to make a complaint becomes null
and void.
Keep the door closed during use (the product is not approved
for use with open door
3.1 Fire Prevention Measures
There is a certain element of danger every time you use
your fireplace. The following instructions must therefore be
followed:
• The minimum safety distances when installing and using
the fireplace are given in fig. 1A and fig. 1B.
• Ensure that furniture and other flammable materials are
not too close to the fireplace. Flammable materials should
not be placed within 1,05 metre of the fireplace.
• Allow the fire to burn out. Never extinguish the flames with
water.
• The fireplace becomes hot when lit and may cause burns
if touched.
• Only remove ash when the fireplace is cold. Ash can
contain hot embers and should therefore be placed in a
non-flammable container.
• Ash should be placed outdoors or be emptied in a place
where it will not present a potential fire hazard.
In case of chimney fire:
• Close all hatches and vents.
• Keep the firebox door closed.
• Check the loft and cellar for smoke.
• Call the fire service.
Before use after a fire an expert must check the fireplace and
the chimney in order to ensure that it is fully functional.
4.0 Installation
The fireplace surround must have a minimum opening of HxWxD
= 515x715x490 mm. It is also important to allow space for
insulation around the surround. If using a wide frame (optional
extra), it will overlap openings to HxW = 558x755 mm.
A narrow frame is included with the product. It is possible to
move this frame and a wide frame (optional extra) up to 40
mm to make it easier to adapt the product for different flue
pipe positions.
4.1 Floor
Foundation
You need to make sure the foundation is suitable for a fireplace.
See “2.0 Technical Data” for specified weight.
Requirements for protection of wooden
flooring beneath the fireplace
The Jøtul C24 has a heat shield underneath to protect the floor
from radiated heat. The product can therefore be positioned
directly on a wooden floor that is covered by a sheet of metal
or other non-inflammable material. The recommended minimum
thickness is 0.9 mm. The plate must cover the entire floor
surface within the surround.
We recommend the removal of any flooring that is not attached
to the foundation (“floating floors”) beneath the installation.
Any floor covering of inflammable material, such as linoleum,
carpets, etc. must be removed from under the floor plate.
Requirements for protection of inflammable
floors in front of the fireplace
The floor in front of the fireplace must be protected by a sheet
of metal or other non-inflammable material. The recommended
minimum thickness is 0.9 mm. The floor plate must comply with
national laws and regulations.
Contact your local building authorities regarding restrictions and
installation requirements.
4.2 Ceiling
Distance from hot air vents in the top ( Fig. 1B-V or 500 mm).
ENGLISH

7
4.3 Insulation requirements
When the cassette is fitted into a surround with combustible
walls protected by insulating material, the following types
and thicknesses can be used:
50 mm Jøtul JGFW-5 fireproof board (specific thermal
conductivity = λvalue = 0.06 W/mK)
50 mm (min. 38 mm) Rockwool (λvalue = 0.046 W/mK)
50 mm (min. 31mm) Rockwool (λvalue = 0.037 W/mK)
Other materials may be used. See Fig. 33 for minimum
insulation thicknesses for known Lambda (λ) values.
Note: The insulation must be mounted in a way that doesn`t
allow heat to be conducted through the securing materials
to the combustible walls.
Fig 3
Minimum Insulation Thickness
[mm]
Lambda value [W/mK]
JGFW-5 firewall
RockWool BB Lambda 0,046
RockWool BB Lambda 0,037
0
10
20
30
40
50
60
70
0,020,030,04 0,05 0,060,070,08 0,09
4.4 Outside air connection
Warning! You need to ensure an adequate supply of outdoor
air to the room in which the product is being installed. An
inadequate supply of air may cause smoke to be emitted into
the room. This is highly dangerous! Symptoms of this may be
the smell of smoke, feeling of tiredness, nausea and sickness.
If the house is tightly sealed and insulated and/or has a
mechanical air extraction system, the room should be fitted
with vents or a separate duct to provide an additional supply
of outside air. Ducts in the room where the stove is installed
must be made of a non-combustible material such as a flexible
aluminium pipe with an internal diameter of 80 or 100 mm.
A fresh air duct connector is included with the product. The
connector can be attached in three different places (Fig. 2)
depending on how the duct is entering the surround or heart.
A kit for outside air connection with air duct, wall grille and
insulation is an optional extra. If outside air does not pass
through a separate duct, the lever (Fig. 27A) must be in the open
position. If the air to the product passes through an outside
air duct, the lever must be in the closed position. See Chapter
4.11 for installation of outside air connection.
4.5 Air circulation
If installing in a new fireplace surround (Fig. 2), air must be able
to circulate between the cassette and the masonry.
Min. circulation air:
Base: 500 cm2free opening.
Top: 750 cm2free opening.
This is a safety measure to ensure that the build-up of heat
inside the fireplace surround does not become too great and
that the output of heat to the room is adequate. If the product
is installed in an approved hearth, the opening in the base can
be omitted and the opening in the top can be 100 cm2.
4.6 Hot air distribution/fan
A fan (optional extra) can be fitted inside the product to increase
hot air distribution. The fan should be fitted before the product
is installed. See the instruction manual for fan installation
(included with the fan).
ENGLISH

8
4.7 Chimney and flue pipe
• The fireplace can be connected to chimneys and flue pipes
approved for solid fuel fireplaces with flue gas temperatures
as specified in «2.0 Technical Data».
• The cross-section of the chimney must be at least that of the
flue pipe. Use «2.0 Technical Data» to calculate the correct
chimney cross-section. NB! The minimum recommended
chimney length is 3.5 m.
• For recommended chimney draught, see «2.0 Technical
Data». If the draught is too strong, action must be taken,
e.g. install and operate a flue pipe damper in order to reduce
the draught.
• The chimney and sweeping hatch must be inspected to
ensure they are tightly sealed to prevent leakage. If there is
a leak, less air will be pulled through the stove. Your local
fire safety office can carry out an inspection of the chimney.
• The chimney must be connected in accordance with the
installation instructions of the chimney supplier.
• Before a hole is made in the chimney, the fireplace should
be test-mounted in order to correctly mark the position of
the fireplace and the hole in the chimney. See Fig. 1 for
minimum dimensions.
• It is extremely important for connections to have a degree of
flexibility. This is to prevent any movement in the installation
leading to the formation of cracks.
• It is important for the joints/flue pipes to be sealed
completely. Air leakage may cause malfunction.
• An adapter that makes it easier to install the flue pipe is
available as an optional extra. See Chapter 4.11.
• A flue gas bend that alters the direction of the flue gas by
more than 45° must be fitted with a sweeping hatch. Note
that it is possible to sweep from the inside of the burn
chamber. See Chapter 7.2.
• NB: A correct and airtight connection is extremely important
for the function of the product.
• Weight must not be transferred from the fireplace structure
to the chimney. The fireplace structure must not hinder the
chimney’s ability to move, and must not be anchored to
the chimney.
4.8 Before installation
Make sure that the Jøtul C 24 fits inside the hearth or surround,
Fig. 1 shows the minimum dimensions. You must allow space
between the cassette and the masonry for thermal expansion
of the cassette stove.
The Jøtul C 24 IT comes in two packages.
Jøtul C 24 standard package:
• When the product is unpacked, remove the bag of screws
and the box with the outside air connector, 2 hot air outlet
connectors and the oven glove from the burn chamber.
• Also remove the ash pan, fire grate and a wooden block
(used for transportation) just below the product’s smoke
outlet.
• The package also contains a box with a narrow outer frame.
• Check the product for signs of damage and make sure that
the control handles work.
Jøtul C 24 Heat Exchanger package:
• Check the product for signs of damage.
4.9 Door hinge reversal
It is possible to change the door of the Jøtul C 24 from left-
hinged to right. If you wish to change the hinges, this should
be done before installation. If you do not wish to change the
hinges, proceed to Chapter 4.10.
Fig. 4
12
1. Remove the side burn plates by lifting them slightly and
pulling out at the bottom.
Fig. 5
A
2. Loosen the 2 screws (Fig. 5A) holding the hinges in place.
Hold the door so that it does not fall down when loosening
the last screw.
3. Place the door face down on a flat surface.
ENGLISH

9
Fig. 6
180o
4. Remove the lock catch on the right-hand side of the product
and attach it to where the door hinges were on the left-hand
side.
Fig. 7
A
A
A
A
B
C
5. Remove the handle (Fig. 7B) from the door lock. Loosen
the 4 screws (Fig. 7A) holding the door lock and hinges in
place. Scrape any traces of glue offthe surfaces (Fig. 7C).
Fig. 8
180°
180°
180°
6. Rotate the parts of the door lock axis by 180°.
Fig. 9
A
7. Install the door lock and hinge on the opposite side (Fig. 9).
8. Place the door on the product. Note: the position of the door
can be adjusted slightly by loosening the screws (Fig. 5A)
a little. Tighten the screws.
9. Refit the handle.
ENGLISH

10
Fig. 10
10. The door can also be adjusted upwards or downwards
slightly on the door lock side by forcing it into correct
position NB! The door cannot be fully closed when
adjusting it!
4.10 Assembly/installation.
Installation
The product is heavy! Ensure you have help when positioning
and installing it.
1. Position the product in the surround so that the front part of
the product and the front part of the surround are aligned.
Fig. 11
AA
2. Unscrew the 4 screws (Fig. 11A) below the fire grate using
a 5 mm Allen key from the bag of screws.
Fig. 12
B
A
3. Adjust the 4 leg screws (Fig. 12A) below the screws that
you just removed until the product is level. Use the 4 mm
Allen key (Fig.11B) from the bag of screws
ENGLISH