Jøtul FS 166 -I 570 User manual

Monterings- og bruksanvisningen må oppbevares under hele produktets levetid. These instructions must
be kept for future references. Ce manuel doit être conservé pour de futures interventions. Wir empfehlen
Ihnen, die Montage- und Bedienungsanleitung für spätere Zwecke sorgfältig aufzubewahren.
Jøtul FS 166 - I 570
Manual Version P02
Jøtul FS 166 -I 570
NO - Monterings- og bruksanvisning 2
DK - Monterings- og brugsanvisning 11
SE - Monterings- och bruksanvisning 20
FI - Asennus- ja kättöohje 29
GB - Installation and Operating Instructions 38
FR - Manuel d’installation et d’utilisation 47
ES - Manual de instrucciones 56
IT - Installazione e Istruzioni per l’uso 65
NL - Installatie- en montagehandleiding 74
Jøtul FS 166 - I 570

38
ENGLISH
1.0 Relationship with the
authorities
Jøtul FS 166 – I 570 is a freestanding product with Jøtul I 570 as
the burn chamber,which can be positioned against inflammable
walls at the distances described in Fig. 1.
Installation of the fireplace must be according to local codes and
regulations in each country.All local regulations,including those
that refer to national and European standards,shall be complied
with when installing the product.
Installation instructions for the surround are included.
Installation and user instructions for the insert are enclosed
with the product.
For day-to-day use, maintenance, servicing, etc., please see this
document. The installation may only be used once it has been
inspected and a certificate of completion has been issued.
Prior to using the product the installation must be approved by
a qualified person.
The classification label for the free-standing products is enclosed
with the surround’s installation instructions and is to be placed
on the backside of upper back plate (Fig. 2 - position 15).
Thiscontainsinformationaboutidentificationanddocumentation
for the product.
2.0 Technical data
Weight, surround: Approx. 440 kg
Weight, burn chamber: 220 kg
Height: 1835 mm
Width: 1025 mm
Depth: 536 mm
Height, centre smoke outlet: 1587 mm
(Technical data for burn chamber - see installation manual for
Jøtul I 570)
Optional equipment
• Ash solution cat.no. 50012921
Table of contents
1.0 Relationship with the authorities.............38
2.0 Technical data.............................................38
3.0 Parts of the surround................................ 40
4.0 Prior to installation.................................... 41
5.0 Mounting....................................................42
6.0 Installation completed.............................. 46
6.0 Maintenance ............................................. 46
7.0 Optional equipment ................................. 46
On all our products there is a label
indicating the serial number and
year. Write this number in the
place indicated in the installation
instructions.
Always quote this serial number
when contacting your retailer or
Jøtul.
les combustibles recommandés.
Respectez les consignes d'utilisation. Utilisez uniquement
Verwenden Sie nur empfohlenen Brennstoffen.
Montage- und Bedienungsanleitung beachten.
Follow user`s instructions. Use only recommended fuels.
standard
Certificate/
The appliance can be used in a shared flue.
Minimum distance to adjacent combustible materials:
Emission of CO in combustion products
Serial no: Y-xxxx, Year: 200x
Manufacturer:
N-1602 Fredrikstad
Norway
Jøtul AS
POB 1441
Sweden
EUR Intermittent
Nominal heat output
Norway
Country
Operational type
Fuel type
Operation range
Efficiency
Klasse II
Classification
Standard
Flue gas temperature
Room heater fired by solid fuel
Product:
Jøtul
SP Sveriges Provnings- och
221546
Forskningsinstitut AB
SP Swedish National
Testing and Research
Institute
:
Approved by
:
:
:
:
:
:
:
Minimum distance to adjacent combustible materials:
OGC SP
EN
Serial no.

39
1300
Measurements according to EN 13240
Min. measurements floor plate X / Y= Acc. to national regulatives and regulations.
Combustible wall
900079-P01
Jøtul FS 166 - I 570
Radiation zone
y
Fig. 1
X
512
1025 536
1587
243
Ø210
Min 2300
50
294
1835
Min 465
243
ca 565
ca 15mm
ca 1367
400
912
ENGLISH

40
3.0 Parts of the surround
Fig. 2
ENGLISH

41
and installation requirements.
• Connection to the chimney must be performed in accordance
with the installation instructions of the chimney supplier.
• Makesure that the fluepipe risesall theway upto thechimney.
• Please note that it is extremely important for connections to
have a degree of flexibility.
For recommended chimney draught, see «2.0 Technical data» in
the insert manual.
4.8 Preparation
The basic product is supplied in two packages:
1. the burn chamber,
2. and soap stones with mounting sections.
NB: Check that there is no visible damage to the product when
you unpack it, and make sure that the control handles move
freely.
The burn chamber is heavy, – make sure it does not topple over
while you are installing it!
Ensure you have help when positioning and installing it.
The product is supplied together with 3 manuals:
1. General user and maintenance manual
2. Jøtul FS 166 - I 570 (surround)
3. Jøtul I 570 (burn chamber)
The surround consists of the following elements
(Fig. 2):
Part Description Total
2 Bottom plate 1 pcs
3 Leg 4 pcs
4 Insert support plate 1 pcs
5 Side stone 12 pcs
6 Corner stone 10 pcs
7 Front stone 4 pcs
8 Distance piece 4 pcs
9 Corner stone over insert 2 pcs
10 Top stone, front 1 pcs
11 Top stone, left 1 pcs
12 Top stone, right 1 pcs
13 Top grid 1 pcs
14 Support bracket 1 pcs
15 Rear plate, upper 1 pcs
16 Rear plate, middle 1 pcs
17 Rear plate, lower 1 pcs
18 Bracket 1 6 pcs
19 Bracket 310 pcs
20 Bracket 6 4 pcs
21 Bracket 54 pcs
22 Bracket 26 pcs
23 Bracket 4 4 pcs
24 Screw countersink unb, M6x16 8 pcs
25 Heat shield, top 1 pcs
26 Adjustable leg 4 pcs
27 Heat shield for flue pipe 1 pcs
28 Screw Hexagon, M10x35 4 pcs
29 Screw hexagon cap flange, M6x10 2 pcs
30 Nut hexagon cap flange, M6 2 pcs
Prior to installation, decide on the following:
1. Where the smoke outlet should be.
2. Ash collection system if being used.
Refer to manuals for parts installation instructions.
4.0 Prior to installation
4.1 Foundations
You need to make sure the foundation is suitable for a stove.See
“2.0 Technical data” for specified weight.
Remember: If a steel chimney resting on the burn chamber is
being used, the weight of the steel chimney should be taken
into account.
NB: It is extremely important that the product be stable; the
surface it is installed on must be completely inflexible.
It is recommended that flooring that is not attached to the
foundation – «floating floors» – be removed beneath the product.
4.2 Floor covering
Jøtul FS 166 - I 570 has an airtight bottom plate and no
extra floor covering is required beneath the product.
Any floor covering of inflammable material, such as linoleum,
carpets, etc. must be removed from under the product.
4.3 Floor plate
A plate made of steel or some other suitable non-inflammable
metal (optional extra) is placed in front of the hearth.
The floor plate must comply with national laws and regulations.
Contact your local building authorities regarding restrictions and
installation requirements.
4.4 Air supply
There must be a flow of air between the burn chamber and the
surround.This is to ensure that there is not too great a build-up
of heat inside the surround.
NB: It is extremely important that air openings not be covered.
See fig. 1 for distances.
4.5 Steel chimney
If a top-mounted steel chimney is used, an uninsulated pipe is
fitted from the burn chamber to approximately 10 mm through
the top stones. Make sure that the gasket is properly seated
between the flue pipe and the smoke outlet. Then fit the steel
chimney in accordance with the chimney supplier’s installation
instructions.
4.6 Ceiling
Make sure the room where the Jøtul FS 166 - I 570 is to be placed
has a ceiling height of at least 2300 mm.
4.8 Chimney and flue pipe
• The stove must be connected to a chimney and flue pipe
approved for solid fuel fireplaces with flue gas temperatures
as specified in «2.0 Technical data» in the insert manual.
• The cross-section of the chimney must be at least that of the
flue pipe. To calculate the correct chimney cross section, see
«2.0 Technical data» in the insert manual.
• Several solid fuel products can be connected to the same
chimney system if the chimney cross-section is adequate.
Contact your local building authorities regarding restrictions
ENGLISH

42
3. To make the installation easier, remove the burn plates (fig.
3 B-G/F),baffle plate (fig.3 c-A),exhaust deflector (fig. 3 C-B),
log retainer (fig. 3 B-C), inner bottom (fig. 3 B-D), and grate
(fig. 3 B-E). See section “4.1 Replacing the burn plates, baffle
plate and exhaust deflector”.
5.0 Mounting
NB:Thebasemustbelevel.Max.1mm/mtolerance.Thisisextremely
important to ensure that the rest of the installation is correct.
All stones must be level. This has to be checked for each new
layer of stones. If necessary use small pieces of steel or silicon
to adjust the height of the stones.
Important!
Bear in mind that the stones may be damaged if they are
handled roughly. Do not knock the mounting brackets too hard.
Installation should be carried out by a qualified person.
Fig. 4
Necessary tool during mounting.
4mm
10mm/13mm/17mm
Spirit level, allen key, folding ruler, wrench, rubber mallet and
hammer.
Fig. 5
1. Dismount the insert’s heat shield by unscrewing the upper
screw on both sides of the insert (fig. 5 A).Loosen the lower
screws (fig.5 E) somewhat and pull the heat shield upwards
and then remove it.
2. Lay the insert carefully down on its back (you can protect
the floor with the wooden pallet and cardboard packaging).
4.9 Preparation/installation
NB: Check that the fireplace is undamaged before installation
begins. The product is heavy! Ensure you have help when
positioning and installing it.
After unpacking the insert take out the box with contents. To
make the product lighter, remove the door.
Fig. 3 A
1. Open the door.
2. Tap out the hinge pins and pull out the door.
Fig. 3 B
Fig. 3 C
ENGLISH

43
Fig. 6
1.
A
B
Mount the four cassette legs (Fig. 6 A).
2. Screw the foot screws (Fig. 6 B) through the foot. Adjust
lenght to approx. 15 mm (see Fig. 1 and Fig. 13).
3. Stand the product carefully up.
4. Reposition the previously removed heat shield (see Fig. 5).
Fig. 7
A
B
1. Unscrew the upper heat shield at the rear (Fig. 7 A). Turn it
upside down and screw it firmly in position using the same
screws it was fastened with before.
2. If top smoke outlet: Mount the heat shield for flue pipe
(Fig. 7 B).
Fig. 8 A
NB! Hole in floor for external air.
Fig. 8 B
1.
D
A
E
B
C
50 mm
Assemble the stand.The stand consist of bottom plate (Fig.
8 B-A), 4 legs (Fig. 8 B-B) and top plate (Fig. 8 B-C).
2. It is very important that the legs are mounted as shown in
figure 8 B-D.
3. Place the stand at its final position and make sure a gap of
min. 50 mm to the wall.
4. The floor and stand has to be completely level (Fig. 8 B-E).
This is extremely important to ensure that the rest of the
installation is correct.
ENGLISH

44
Fig. 9
Bracket 3
Bracket 6
Bracket 1
Bracket 5
Bracket 4
Bracket 2
Br
ac
ke
t
2
Fig. 10
A
B
3mm
NB!: Do not use corner stones marked «223628» before the
fourth layer.
1. Fit the first layer of soap stone on the bottom plate. Use
bracket 4 and bracket 6 under to hold them in place.
2. Make sure the layer is level and placed correct on the bottom
plate (Fig. 10 A). Use a rubber mallet to adjust the stones.
3. Place the front stone and corner stones of the second layer
using bracket 1 (Fig. 10 B).
Fig. 11
A
B
1. Position the burn chamber on the stand.Make sure that the
burn chamber is positioned stably.
2. Refit all the parts that were removed for easier handling
of the insert.
3. Mount the first rear plate to bracket 6 that is placed under
the first layer of soap stone.
4. Mount bracket 3 from the inside through the back plate (Fig.
11 A).Use a hammer and knock it gently into the soap stone.
5. Place the side stones of the second layer between the corner
stones and the rear plate. Use bracket 3 to hold it in place
(Fig. 11 B).
6. Make sure everything is level.
Fig. 12
A
C
D
B
1. Remove the lower cover (Fig.12 A).
2. Fit the decorative frame over the door and hook it over the
front (Fig. 12 B).
3. Attach the trim panel with the same screws as those used
for the lower cover (Fig. 12 C).
4. Remove the M8 screw provided (Fig. 12 D).
ENGLISH

45
Fig. 13
1.
ca. 15mm
4 psc. M10x35
B
A
Centre the insert laterally.
2. Position the insert and the frame against the front of the
surround.
3. Make sure that there is clearance between the lower edge
of the frame and the stone below (Fig. 13 A) by adjusting the
foot screws (Fig. 13 B).
4. Adjust the foot screws until the insert is perfectly level.
Fig. 14
A
1. Use bracket 5 (Fig. 14 A) on layer 3 and 4.
2. Adjust the brackets with bare hands if necessary to make
them hold the stones together.
Fig. 15
A
B
223628
1. Place the attachment bracket on the special corner stone
223628 (Fig. 15 A). The front stone (Fig. 15 B) of layer 5 shall
rest on the attachment bracket.
Fig. 16
A
B
C
1. Install the flue pipe. Top smoke outlet (Fig. 16 A) or rear
smoke outlet (Fig. 16 B). If a rear smoke outlet: Remove the
knockout in the rear plate (Fig. 16 C).
Fig. 17
A
B
ED
C
F
If top smoke outlet:
1. Place the last layer (Fig.17 A) and the top layer (Fig.17 B).Use
bracket 2,bracket 4and bracket 6 between the last layer and
the top layer (Fig. 17 C).
2. Remove the knockout and place the top grid (Fig. 17 D).
3. Place the distance pieces (Fig. 17 E), remove the knockout
and place top heat shield (Fig. 17 F).
If rear smoke outlet:
1. Place the last layer (Fig.17 A) and the top layer (Fig.17 B).Use
bracket 2,bracket 4 and bracket 6 between the last layer and
the top layer (Fig. 17 C).
2. Place the top grid (Fig. 17 D).
3. Place the distance pieces (Fig. 17 E) and place top heat shield
(Fig. 17 F).
ENGLISH

46
6.0 Installation completed
See the General user and maintenance manual for Jøtul I570 for
the use and maintenance of the product.
7.0 Maintenance
If you have the misfortune to find scratches in the surface,these
may be polished out using a fine sandpaper. If deeper scratches
are present, a paste made of powdered soap stone and water
glass (sodium silicate) can be made up which you can use to fill
the stone.
8.0 Optional equipment
Ash collection system - cat. no. 50012921
ENGLISH

83

Jøtul arbeider kontinuerlig for om mulig å forbedre sine produkter,og vi forbeholder oss retten
til å endre spesifikasjoner, farger og utstyr uten nærmere kunngjøring.
Jøtul bemüht sichständig um dieVerbesserung seiner Produkte,deshalb könnenSpezifikationen,
Farben und Zubehör von den Abbildungen und den Beschreibungen in der Broschüre abweichen.
Jøtul pursue a policy of constant product development. Products supplied may therefore differ in
specification,colour and type of accessories from those illustrated and described in the brochure.
Jøtul s’attache à l’amélioration constante de ses produits. Ceux livrés peuvent présenter
quelques différences d’aspect, de couleur et d’accessoires par rapport au présent document.
Kvalitet
Jøtul AS arbeider etter et kvalitetssikringssystem basert på NS-EN ISO 9001 for utvikling,
produksjon og salg av ildsteder. Vår kvalitetspolitikk skal gi kundene den trygghet og
kvalitetsopplevelse som Jøtul har stått for siden bedriftens historie startet i 1853.
Qualität
Jøtul AS hat ein Qualitätssicherungssystem,das sich bei Entwicklung,Produktion und Verkauf
von Öfen und Kaminen nach NS-EN ISO 9001 richtet. Diese Qualitätspolitik vermittelt unseren
Kunden ein Gefühl von Sicherheit und Qualität,für das Jøtul mit seiner langjährigen Erfahrung
seit der Firmengründung im Jahre 1853 steht.
Quality
Jøtul AS has a quality system that conforms to NS-EN ISO 9001 for product development,
manufacturing, and distribution of stoves and fireplaces. This policy gives our customers
quality and safety piece of mind as a result of Jøtul’s vast experience dating back to when the
company first started in 1853.
Qualité
Jøtul AS applique une procédure de contrôle de qualité conforme à la norme NS-EN ISO 9001
pour le développement,la fabrication et la distribution de sa gamme de poêles,foyers et inserts.
Cette démarche assure à nos clients une tranquillité d’esprit sur la qualité et la sécurité, due
à une expérience remontant à la création de la société en 1853.
Jøtul AS,
P.o. box 1411
N-1602 Fredrikstad,
Norway
www.jotul.com
Cat.no. 10026632
223644-P02
Jøtul AS, Feb. 2012