Jabo Boat Jabo-2AG/2BG User manual

www.jaboboat.com Email: [e-mail] Phone:[phone]
1
JABO-2AG/2BG Auto Bait Boat/Fish Finder
Version：2020080
Please read the instructions carefully before using this product
JABO2AG/2BG is the 4th generation product of JABO series of intelligent bait boats.
The product adopts GPS positioning and electronic compass navigation. It can store
16 target bait positions, and can automatically (manually) set the starting position.It is
a bait/fish finding robot that can auto move from start point,auto navigate to nesting
positions,auto release bait(hooks,etc),then accurately return to start point.Meanwhile a
highly sensitive fish finder and a lure light are already installed at bottom which can
detect water depth,terrain,temperature,fish size and attract fish at night.
1. It has the characteristics of precise positioning and precise navigation. For
positioning, the navigation error radius is 0-1 meters.
2. Directional and fixed-distance automatic navigation, and the navigation distance
which ranges from 20 meters to 300 meters (adjustment interval of 20 meters) can be
preset on the remote control to realize automatic navigation at a distance of 300.

www.jaboboat.com Email: [e-mail] Phone:[phone]
2
3. Store up to 16 target bait positions. After the target bait positions are determined
for the first time, they can be utilized again on the same water areas,or in a different
fishing position within a radius of 1000 meters. This not only brings more chances of
locating larger fish,but also saving your baits and increase the fun of fishing.
Especially for night fishing, when ordinary bait boats cannot achieve accurate baiting
(hook releasing), but JABO2AG/2BG can be used to accurately target bait positions
(hook release positions) even in the dark night.
4. The working frequency of JABO2AG/2BG is 2.4GHz, 250 frequency points can
be set. By setting up different frequency points, multiple bait boats can be used at the
same time without interfering with each other in the same lake/river.
5. While using JABO2AG/2BG the start position can be set manually (automatically).
After the start position is successfully set, the bait boat can return by itself safely
every time it sets off without worrying to get lost. If the user does not manually set the
start position, JABO2AG/2BG can also automatically set the start position. Since it
takes time to automatically to receive GPS satellite signals, the start position may be a
slightly further. In order to make it accurate,wait only 1-2 mins for it to fully set up.
6. Every time you turn on power, the bait boat will automatically start to establish
contact with the navigation satellite. It usually takes 3 minutes to successfully
establish a contact.
7. The unique design of the JABO2AG/2BG bait boat's automatic lifting bait bin has
the advantage that the feeding positions can be seen visually, and the bait bin is
automatically flip,recover like an unloading truck and travels more smoothly. These
characteristics become more obvious after the realization of automatic navigation.
8. The design of the built-in propeller overcomes the defect that the external
propeller is easy to be entangled by weeds. With a 4-leaf propeller system,the motor is
powerful with much loads but also quiet in water so as not to disturb the fish.

www.jaboboat.com Email: [e-mail] Phone:[phone]
3
9. In order to be suitable for dawn or sunset/night fishing, the bait boat is equipped
with two different colors of tail lights. At night, the fisherman can also identify the
sailing direction of the boat according to the different colors of the indicator lights. In
order to help fishing at night, JABO2AG/2BG is equipped with a big night light in
front that can be remotely switched on and off anytime.
10.JABO2BG has the functions of detecting fish, measuring the depth of water.
Temperature.There’s also a lure light under the boat,just next to the fish finder.
11.JABO2AG/2BG is not suitable for use in the beaches, rapid flowing waters) and
environment with heavy wind and waves,or bad weather.
Technical Parameters:
Model Number-JABO2AG/2BG
1. Dimension: 615*265*180mm
2. Weight: 3KG (including 2*3.7V10A lithium battery);
3.4KG (including 3.7V20A lithium battery)
3. Power supply:
10A/3.7V lithium battery can work continuously for 2-2.5 hours
20A/3.7V lithium battery can work continuously for 3-4 hours
36A/3.7V lithium battery, can work continuously for 5-6 hours
4. Speed: 80 m/min
5. Remote control distance: 300 meters(1,000 meters between nesting positions).
6. Drive components: dual 380 motor gearbox drive (2AG), dual 545 motor direct
drive (2BG), built-in 4-leaf propeller.
7. Main orders: forward, back, turn right, turn left, release hook (releasing baits),
automatic driving in directional fixed distance, automatic positioning, automatic
nesting, automatic return. (2BG) Water temperature measurement, boat bottom lights
to lure fish, water depth measurement, fish detection (small and large fish can be
distinguished),
8. Bait bin load: 2-2.5 kg
9. GPS positioning, can store 16 target feeding positions.
10. Electronic compass orientation + satellite navigation, the error radius is 0-2M.
Remote Control Parameters
1.Remote control size: 165×42.5×96mm
2. Power supply: 3.7v lithium rechargeable battery.
3.LCD: FSTN128×128 dot matrix type
4.Screen size: 45mm×45mm
5. Sonar fish finder frequency: 200KHz (2BG)

www.jaboboat.com Email: [e-mail] Phone:[phone]
4
6. Sonar fish finder angle: 20 degrees (2BG)
7. Water depth detection range: 1-30 meters (2BG).
8. Water depth detection resolution: 0.1 meter (2BG)
9. Underwater contour display: Yes (2BG)
10. Water temperature detection range: 0-50 degrees Celsius (2BG)
11. Unit conversion: meters/inch; Celsius/Fahrenheit
12. Remote control frequency: 2.4G
13. User-selectable channels: 250
14. Low battery alarm display: Yes
15. Remote control distance: 300 meters
16.GPS accuracy: radius 0-2 m
17.GPS satellite capture time: 2-5 minutes
18. Current latitude and longitude display: Yes
19 .Maximum navigation distance: 1000 meters (Note: The maximum navigation
distance is not the remote control distance. For example, if the fisherman drives the
bait boat at point A to point B to cast bait, the distance between points A and B should
be less than 300 meters; next time after changing to point C, as long as the two points
C and B are less than 1000 meters, and there is no obstacle in the middle of the water,
he can navigate the boat from point C to point B to cast bait).
How to use the remote control:
First turn on the power switch, after the two tail lights flash, follow the steps below,
JABO
Long press the power button for 2 seconds, the screen enters the
boot page, and the "JABO" welcome page appears first

www.jaboboat.com Email: [e-mail] Phone:[phone]
5
Compass Calibrate
Y
N
Compass calibration: When using the bait boat for the first time
or to another distant lake, you need to make new calibration,if
you have done this before,select No,and directly go to next step)
Press the "set start" key, select "Yes", and then press the "S" key
to confirm.
5 m offshore
When “5m offshore” appears,Control the boat to 5-10 meters
away from shore,press “S” to enter compass calibration.
Compasss left
“Compass left” means the boat auto turns left from 0-360
degree(1 circle),when the second circle completes,press the "S"
key to confirm.
Compass right
“Compass right” means the boat auto turns right from 0-360
degree(1 circle),when the second circle completes,press the "S"
key to confirm.
Compass Save
Y
N
"Calibration save",the default is "Y", after pressing "S",the
compass calibration data is saved.
Set Start
Y
N
It is very important to set the GPS start point. You need to
determine the GPS start position every time you use it. If not set,
the bait boat will not be able to return unless you manually
control it. Select "Yes" in this step. After the GPS start position is
established, a "*" icon will appear on the LCD screen, which
represents the starting position.
Please be noted that it takes 2-3 minutes for the boat’s receiver to establish a
connection with the satellite system. If the power-on time is too short, the connection
with the GPS has not been established. And after selecting "Yes", no "*" appears on
the LCD screen , it means that the starting position has not been established, you need
to wait for 2-5 minutes, and then select "Yes" until the starting position is established.
If it is established for a long time, you can press the N key to enter the navigation
setting page and select "Set the start": press the "S" key to complete the setting.
Set start,enter the operation interface:
Icon from first left to right:
1. Signal strength,full signal is 6 grills.
2. Remote control battery indicator
3. Boat battery indicator
4. Boat status(left,right or forward)
5. Satellite icon
In the second row,E means longitude,N means latitude.The "*" on the first digit on the
left indicates that the navigation module has started to work.
Before fully establishing contact with the navigation satellite, the latitude and

www.jaboboat.com Email: [e-mail] Phone:[phone]
6
longitude coordinates display a series of "X". At this time, the "X" is meaningless.
After the boat has established a connection with the satellite, the displayed value of
the latitude and longitude is the current satellite positioning of the boat.
After setting the start position, enter the operation page, start operating.
Parameter setting:
After entering the operation page, press the key "S", the screen enters the parameter
setting page:
Sensitivity
50
Sonar sensitivity could be between 01-99,the highest sensitivity does
not mean it is best,when in highest value,it will vastly increase the
interfering signal,the data shown may not be referred and thus useless,
the default value i 50,which suits water depths from 1.8-10
meters(6-33ft deep)
Serial number
001
The serial number is the code of the remote control. Remote controls
with different codes are used in the same water without interfering with
each other. 0-250 serial numbers can be set. Factory default "000"
Temperature
ºF
The temperature unit shows Celsius and Fahrenheit.
Length Unit
FT
Length unit is feet
Beep
On
Key tone, which can be turned on or off
Backlit
On
LCD backlight, selectable on or off
Depth range
Auto
Depth range "m": The default setting is "Auto".
Speed Rate
80%
Speed adjustment, default is 80%, range is 60-99%
Refresh
5
Refresh adjustment is to adjust the LCD screen shift time, the
adjustment range is 0-9 seconds,default is 5 seconds.
Compass Ca
00
This compass calibration is different from the compass calibration at
startup. It is used to fine-tune the angle of the compass when the
electronic compass is deviated. The adjustment range is -30—+30°.
The adjustment method will be explained in detail later.
Off track
00
It is used to adjust the yaw of the boat. When the boat is leaning to one
side when going straight, it can be adjusted through this item.
Adjustment range -50-+50.
Function buttons on the right:

www.jaboboat.com Email: [e-mail] Phone:[phone]
7
①A/H key: automatic/manual conversion key. When the boat is in automatic
navigation, manual operation is invalid. After pressing the A/H key, the following
options appear:
At this time, press the "S" key to continue the automatic navigation, if you press "No",
the automatic navigation function will exit and the manual function will be restored.
②M key: Screen mode conversion. The remote control has 2 screen modes:
1 Navigation mode, displaying the coordinates of the bait
boat, driving status, power of the remote control, power of
the boat’s battery, and the distance to the target point and
starting point.
2 Fish-finding working mode: display the signal strength,
the boat’s running status, the power of the remote control,
the power of the boat’s battery, and the water depth, water
temperature, and fish symbol
③N key: Navigation function selection key. Press the N key, and there will be 5
navigation sub options:
Return: Directly press the "S" key to select “return”, at this time the boat starts to
return, and stops after returning to the starting position.
Save as target point: After pressing the ▼ key, select save to target point, you can
select numbers 1-16, and then press the set key "S", if the selected number is 01, the
current boat position will be saved as target point 01.
Continue Navigation
Y
N
Return
Save Destination
Guide to destination
Set start
Forward
Save target point

www.jaboboat.com Email: [e-mail] Phone:[phone]
8
Navigate to the target point: the premise of applying this function is that at least one
target point has been set, press the ▼ key to enter the navigation to the target point,
and then press the "S" key: press the set key "S" to enter the target point selection:
you can select a number 1-16, press the setting key S again, if the selected number is
01, the target point of this navigation is the No. 1 target point.
Now the "Feeding" option page appears, the default option is "Yes"
After pressing "S" again, enter the "Return”,the default option is "Yes"
In this way, the bait boat completes the one-key navigation of navigating to the target
point "01"—feeding—returning to the starting position.
Set the starting point: If the starting point is not set after the power is turned on, or the
starting point needs to be set for other reasons, you can use this item to reset the
starting point.
Forward: This is the new directional fixed-range automatic navigation function of
JABO2AG/2BG nesting boat. Users can choose 20-300m directional fixed-range
navigation in this option to replace the original need to manually set the nesting point
by remote control, which realizes the true meaning Automatic navigation.
Press ▼ key, select "Forward"
01
Navigate to target
01
Feeding
Y
N
Return
Y
N
Set start
Y
N
Return
Save Destination
Guide to destination
Set start
Forward

www.jaboboat.com Email: [e-mail] Phone:[phone]
9
Press “S” comes up
Press ◄ or ► to set the forward distance, from 20 meters (20 meters apart) to 300
meters, this distance is the distance of the nest boat. After setting the forward distance,
press the S key to enter:
Default is Yes,press “S” to enter：
Default is No,press
“◄“to select Yes
Then save target 01
Press “+’ key to set number 01-16 dens.
Note: At this time, you need to correct the course of the boat manually. After pressing
the “S” button, let go for about 5 seconds, and the boat will begin to move forward.
After the baiting, the boat begins to return. The position where this tipping bucket is
turned over is the set as nesting point.
When setting the forward distance, first predict the required distance. Do not set the
distance to the maximum at the beginning, so as to prevent the bait boat from running
aground to the opposite shore and unable to return.
Before using the directional fixed-distance navigation function, please try it out
several times and learn the operation steps before actually using it to avoid
mis-operation.
Operation Guide.
1. Installation of the lithium battery in the boat: The lithium battery of the nesting boat
has been installed in the boat when it leaves the factory, when the user receives
the boat you only need to open the hatch cover (don’t pull out the plugs that have
been inserted), and connect the battery plug to the power socket inside the boat. When
connecting, pay special attention to the polarity of the battery not to be reversed or
Forward
100M
Feeding
Y
N
Return
Y
N
Save Destination
Y
N
Save target
01

www.jaboboat.com Email: [e-mail] Phone:[phone]
10
reversed. Otherwise it will burn out the receiver and motor drive board. The correct
connection method is to insert the red wire of the plug to the red wire of the socket,
and the black wire to the black wire. After the plug is connected, cover the cabin. The
remote control battery is rechargeable with a USB connector so no need batteries.
2. Function test: Before launching the nest boat, perform a function test.
Power on: Put the nesting boat in a stable place, then turn on the power switch on
the hatch cover, the two tail lights start to flash, indicating that the receiver is working
normally.
Turn on the power switch of the remote control, the tail light changes from flashing
to off, the remote control and the receiver are successfully coded. In order to use
multiple boats at the same water at the same time, an address code (serial number) is
set in the remote control circuit. The serial number of the remote control at the factory
defaults to "000". Each time the nesting boat is turned on, the receiver will first
receive the address code (serial number) of the remote control. Once the code is
completed, as long as the boat’s power switch is not turned off, the boat will receive
the control command of the remote control that is coded with it. In this way, multiple
boats can be operated on the same locations without affecting each other. It should be
noted that every time the nest boat turns on the power switch, there will be a code
matching process.
Forward: Push the handle of the remote control forward, and the two motors of the
nest boat start to rotate. The left and right direction lights are always on. At this time,
the nesting boat is in a forward state.
Turn left; turn right: Push the handle of the remote control to the left or right, and
the nest boat will make a left turn (the right motor rotates forward, the left motor
reverses, and the left direction light flashes), then turns right (left The side motor
rotates forward, the right motor reverses, and the right direction light flashes).
Retreat: Pull back the handle of the remote control, the two motors rotate in
opposite directions, the left and right direction lights flash, and the nest boat retreats at
this time.
3 Pay attention to the following points when operating the bait bin:
The bait bin of the JABO2BG nesting boat is driven by the motor gear box. Don't try
to lift the bait bin by hand. This will damage the mechanical structure of the bait bin.
It is recommended that the user apply some lubricating oil to the screw when the new
boat is launched, which will greatly help improve the performance of the tipping
bucket and extend the life of the screw.
Fish lure light function: Press the fish lure light button on the remote control to turn
on the lure light on the bottom of the boat, and press it again to turn off. The fish trap
status indicator on the LCD display can display the current fish trap status.