Jabra LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES Safety guide

Jabra Link 14201-20
How to connect my Jabra GN9330e with Avaya 1408, 1416,
1608, 1616, 9404, 9408, 9504, 9508, 9608, 9610, 9611G, 9620,
9620C, 9620L, 9621G, 9630, 9630G, 9640C, 9640G, 9641G,
9650, 9650C, 9670
Prerequisite:
Jabra GN9330e + Jabra LINK 14201-20
In combination with one of the following Avaya phones:
1408 / 1416
1608 / 1616
9404 / 9408
9504 / 9508
9608 / 9610 / 9611G / 9620 / 9620C / 9620L / 9621G
9630 / 9630G / 9640C / 9640G / 9641G / 9650 / 9650C / 9670
Connection:
1. Insert the supplied RJ9 to RJ9 connection cable into the socket of
your Jabra GN9350e base marked "phone" and the other end into the
socket of the EHS adapter marked with the "phone" symbol.
2. Now connect the end of the RJ12 to RJ12 connection cable (EHS
adapter) marked in red to the socket of the EHS adapter marked with
"AUX" and the socket of your Jabra GN9350e base marked with "AUX".
3. Now connect the RJ9 to RJ9 connection cable marked white "C" to the
socket of the EHS adapter marked with "Headset/Handset" and with
the "headset" socket of your phone.
Important: 1408/1416 and 9404/9408 phones, use the cable marked
18/11/2022 13:25
https://www.apac.jabra.com/supportpages/jabra-link-14201-20/14201-20/faq/4b5e7a92-
1178-46f7-9a07-1c396e2288bc
Page 1 of 3

with white "A" (instead of the "C" cable).
4. Connect the dial tone sensor to the EHS adapter and attach it to the
centre of the phone speaker.
Please note that full functionality is only available when all the colour-
marked parts of the cables are inserted into the EHS adapter. See photo.
Software setup:
Put the headset into the base and activate the "DHSG" mode.
Hold down the "phone" button on the base of the Jabra GN9330e for
approx. 6 seconds until the online display (blue LED) on the headset starts
to flash. The current software is displayed to you by activating the volume
controller in the form of the charge display (green LED).
LEDs from left to right:
LED 1 = RHL
LED 2 = DHSG
LED 3 = AEI
LED 4 = MSH
18/11/2022 13:25
https://www.apac.jabra.com/supportpages/jabra-link-14201-20/14201-20/faq/4b5e7a92-
1178-46f7-9a07-1c396e2288bc
Page 2 of 3

Now you can switch between the different software modes (LED 1-4) by
using the "volume" up/down controller on the headset. To confirm the
software has successfully installed, the base automatically switches back
to charge mode after approx. 15 seconds.
Base setup:
Set the phone set-up switch to "A".
Headset answer/end:
As soon as the dial tone signal can be heard in the headset, you can answer
the call by pressing the "answer/end" on the headset; by pressing again
the call is ended.
18/11/2022 13:25
https://www.apac.jabra.com/supportpages/jabra-link-14201-20/14201-20/faq/4b5e7a92-
1178-46f7-9a07-1c396e2288bc
Page 3 of 3