Jack Stonehouse EX01001 User manual

OWNER’S MANUAL
OIL FILLED HEATER
MODEL: EX01001/EX01002
EX01003/EX01004
READ AND SAVE THESE INSTRUCTIONS
Attention: Pictures in the IM are for reference only.

1
IMPORTANT SAFEGUARDS
1, Warning: In order to avoid overheating, do
not cover the heater.
2,If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified
person in order to avoid a hazard.
3,This appliance can be used by children aged from 8
years and above and persons with reduced physical, sen-
sory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruc-
tion concerning use of the appliance in a safe way and
understand the hazards involved. Children shall not play
with the appliance. Cleaning and user maintenance shall
not be made by children without supervision.
4,The heater must not be located immediately below a
socket-outlet.
5,Do not use this heater in the immediate surroundings of
a bath, a shower or a swimming pool.
6,Children of less than 3 years should be kept away unless
continuously supervised.
Children aged from 3 years and less than 8 years shall
only switch on/off the appliance provided that it has been
placed or installed in its intended normal operating position
and they have been given supervision or instruction con-
cerning use of the appliance in a safe way and understand
the hazards involved. Children aged from 3 years and less
than 8 years shall not plug in, regulate and clean the appli-
ance or perform user maintenance.
7,CAUTION — Some parts of this product can become
very hot and cause burns. Particular attention has to
be given where children and vulnerable people are
present.

2
8,This heater is filled with a precise quantity of special oil.
Repairs requiring opening of oil-container are only to be
made by the manufacturer or his service agent who should
be contacted if there is an oil leak.
When scrapping the heater, follow the regulations con-
cerning the disposal of oil.
9, Correct Disposal of this product
This marking indicates that this product should not be
disposed with other household wastes throughout the EU.
To prevent possible harm to the environment or human
health from uncontrolled waste disposal, recycle it respon-
sibly to promote the sustainable reuse of material
resources. To return your used device, please use the
return and collection systems or contact the retailer where
the product was purchased. They can take this product for
environmental safe recycling.

3
Use of oil filled radiator
Fig.1
WARNING: IN ORDER TO AVOID OVERHEATING,
DO NOT COVER THE HEATER.
PART FIGURE
Caster assembly
FIN
Power Indicator Light
Termostat Knob
Power Switch Knob
Control panel
Cord wrap
Control box
[Installation of the wheel carrier plate assembly]
1.Place the heater body inversely with the bottom
upward.
2.Connect and tighten two wheel carrier plates to
the body with butterfly nuts as shown in the figure.
3.Place the heater upward after it is installed
securely with the wheels touching the ground.

4
OPERATING INSTRUCTION
[Inspection before start]
1.The power cord shall not be damaged or fractured.
2.This machine uses 220-240V AC power so please verify the rated current of the
power socket is in line with the requirements in the table above and is equipped
with a safety grounding device before use; otherwise, replace the socket.
[Start and power selection]
1.Start
Plug in the power, clockwise turn the thermostat knob to the " " mark position,
then turn on the power switch, the heater starts to work.
2.Power selection
Under normal circumstances, please use the maximum power "III" gear for rapid
heating. If the room temperature reaches a suitable temperature, please choose a
lower power "II" or "I" gear to reduce energy consumption so as to prevent the
room becoming overheated.
[Note]
To use the machine for the first time or to re-insert the socket, please pay attention
to check whether the plug and the socket are fitted well.
<Inspection method>
Insert the power plug into the socket and start for use; after about half an hour, turn
off and pull out the plug. Check whether the plug pins are hot; replace the socket if
so (more than about 50 °C) to avoid burning the plug or even causing a fire caused
by overheating of the socket due to poor contact.
[Temperature adjustment]
During use, if you feel it is necessary to lower the room temperature since it is too
high, you can use the following adjustment modes:
1.Turn the power switch to gear "II" or "I".
2.Counterclockwise turn the thermostat knob back by a certain angle, for which it
indicates that the set temperature is lower when the temperature indication is
closer to the " " position.
[Stop]
Turn the power switch to indication point "0", and then pull out the power plug.
[Movement of the heater]
To move the heater, turn it off first, and pull out the power plug; then push the body
to make the four casters below the body to roll.

5
MAIN TECHNOLOGY SPECIFICATIONS
Power supply: AC220-240V ~ 50Hz
MODEL LO MED HI
POWER REGULATION RANGE (W)
EX01001/EX01003
EX01002/EX01004
600
800
900
1200
1500
2000
1. The electric heater should be cleaned regularly to wipe out the dust on the
surface of flanges. As this may influence the radiating efficiency.
2. Disconnect electricity supply and allow radiator to cool, wipe out dust with a
soft damp cloth. Do not use detergent or abrasives.
3. Do not scrap the surfaces of flanges with sharp hard tools, to avoid surfaces
getting rusty, because of damage of the paint coat.
CLEANING AND MAINTENANCE INSTRUCTION
This manual suits for next models
3
Table of contents
Popular Heater manuals by other brands

Technotherm
Technotherm ISP-W 350 Installation and technical manual

Atlantic
Atlantic SOLIUS instruction manual

TESY
TESY CN04 EIS W Operation and storage manual

CIAT
CIAT Divio Series Installation, Operation, Commissioning, Maintenance

TREVIDEA
TREVIDEA G3 FERRARI G60013 user manual

SHX
SHX SHX20HS2002F instruction manual