Jaga JRT-100 User manual

Jaga Room Thermostat JRT-100 installation, setup & user manual
JRT-100
ATTENTION !!
1.5 m
The room thermostat should be installed at approx.
1.5 m above floor and where the effects of sunlight,
draught or other heat sources: nearby electric fires,
televisions, wall or table lamps may prevent the ther-
mostat from working properly.
Ensure that there will be enough space to allow easy
access to the two retaining screws, located at the bot-
tom of the wall plate.
1.43.4
6
Mount the JRT-100 Room thermostat on a recessed
conduit box (60.3 mm fixing centers). Minimum depth
of 45mm, more is better to fit cables. The Internal
size of the wall recess box must be at least Ø60mm or
50x50mm.
Features
• for 2- and 4-pipe fan coil systems
• (4-pipe): heating and cooling mode / auto changeover heating and cooling
• (2-pipe): heating and cooling mode
• automatic or manual fan speed control
• surface-mounting
• 2 programmable time zones
• 0-10V output
• for valves 24V AC/DC only
• optional external room temperature sensor (order code: 24800.0005.3032)
Technical Data
Power Supply 24V AC/DC
Power Consumption 200 mA
Set Point Range 10~50°C
Ambient 0~50°C
Relative Humidity 85%
Back-light
Sensor NTC 10K, 3950 ohm at 25°C
Accuracy + 1°C (step control by +0.5°C)
Protection Class IP30
Housing ABS to UL94-5 fire retardant plastic
Productdocumentation:
• this manual is an integral part of the unit and must be handed over to the user
after the installation of the device is completed in order to comply with applicable
legal requirements.
• please read the manual carefully so that you understand the information in order
to ensure safety during installation, use and maintenance.
• no liability is accepted for damage resulting from non-compliance with the
guidelines in this installation manual.
Dimensions
M
8.6
8.6 6 1.4 3.4
CE-mark
The CE-mark symbolizes the compliance of the device with the following guide-
lines:
• EN 61000-6-3:2007+A1:2011
• EN 61000-3-2:2006+A1:2009+A2:2009
• EN 61000-3-3:2008
• EN 61000-6-1:2007
IMPORTANT: This manual will guide you through the installation, setup and use of the Jaga Room Thermostat JRT-100. Keep this manual in a
safe place for future reference.

6 november 2015, 10:05 - Jaga N.V.
Jaga Room Thermostat JRT-100 installation
Installation
Warning: The installation of the thermostat should be performed by qualified personnel and must comply with the applicable local
and national electrical codes and utility requirements. All wire connections must be tightened and properly arranged to prevent a
shortcircuit. Turn off the power at the electrical panel to prevent electrical shock or product damage;
1.43.4
6
Place recessed conduit box (60.3 mm fixing
centers).
Carefully remove the front plate:
• locate the (2) release locks on the bottom
edge of the front plate assembly. Use a
small flat head screwdriver to push each of
the release locks up to disengage the lower
clips of the front plate.
• swing the bottom of the front plate slightly
away from the bottom of the back plate.
987654321
Connect the JRT-100 according the wiring
diagrams* on this page.
Mount the thermostat base on the recessed
conduit box and secure it using two mount-
ing screws. Do not over-tighten.
Close the front plate:
• fit the upper clips into the slots at the top
of the grid plate
• insert the lower clips on the front plate into
the lower slots in the back plate. Press on
the cover plate until it locks
WIRING: Warning: Turn off the power at the electrical panel to prevent electrical shock or product damage.
* Wiring diagram
2-Pipe 4-Pipe
1 2 3 4 5 6 7 8 9
1 2 3 4 5 6 7 8 9
0...10V SENSOR GND
0...10V SENSOR GND
L
N
24V AC/DC
L
N
24V AC/DC
C VALVE
H VALVE
H/C VALVE
L
+ -
N
230 VAC
L1 N
5 6
1 4
L
+ -
N
230 VAC
L1 N
5 6
1 4
1 2 3 4 5 6 7 8 9
1 2 3 4 5 6 7 8 9
0...10V SENSOR GND
0...10V SENSOR GND
L
N
24V AC/DC
L
N
24V AC/DC
C VALVE
H VALVE
H/C VALVE
L
+ -
N
230 VAC
L1 N
5 6
1 4
L
+ -
N
230 VAC
L1 N
5 6
1 4
H/CHeating / Cooling GND Ground
HHeating Briza / Clima Canal
Quatro Canal / EC Unit Heater
CCooling Optional externel room temperature sensor

6 november 2015, 10:05 - Jaga N.V.
Jaga Room Thermostat JRT-100 setup / user
Programmable Time settings:
• press the “M” button for 5 seconds to enter “clock setting” (88:88) and “day setting”
• enter 5+1+1 programmable mode
• press “+” and “-“ to set the thermostat “on/off time”
• next mode setting: toggle trough the menu with the “M” button. Activate the programmed time: press and hold the “ “ button for 5
seconds.
To deactivate the programmed time: press and hold the “ “ button for 5 seconds
Week 1st time zone 2nd time zone
Turn on Turn Off Turn on Turn Off
Icons
1
2 3 4
1
2
3 4
1 2
3
4
1 2 3
4
12345 (Monday~Friday) 8:30 12:00 14:00 18:00
6(Sat.) 9:00 12:00 15:00 18:00
7(Sun.) 9:00 12:00 15:00 18:00
Control panel:
Programming & week / day Clock
Room temperature
Set temperature
Room temperature
Set temperature
Heating / Cooling / Auto Select
& Programmable setting
Fan speed:
• Low
• Mid
• High
• Auto fan
Temperature / Parameter setting - / + Fan speed Mode On / Off
Heating
Cooling
Heating & Cooling (4-pipe)
Parameter settings
• set Power Off, bij pressing the “ ” button
• to access the MENU , press and hold “M” and “+” buttons simultaneously for 10 seconds until “01” displays. Press “+” and “-“ to change
the settings.
• toggle trough the menu with the “M” button
Menu Description Range
01 Temp. Offset -8 °C ~8°C
04 Set Point High Limit 10 °C ~40°C
05 Set Point Low Limit 10 °C ~40°C
06 LCD temperature display Room/ Room Set / Set (default Room)
07 Temperature setting / Program 10 °C ~20°C
11 Dead Band 0°C~3°C (default 0,5°C)
12 NTC select Room: internal sensor / Floor: optional external room temperature sensor
13 2-pipes/4-pipes select 2V/4V (default 4V)
14 (0-10V) select dead band or not 0: with dead band 1: without dead band (default 0)
15 Reboot memory OF/LA
19 Restore Re
20 Software version
Sensor ↓

6 november 2015, 10:05 - Jaga N.V.
Jaga Room Thermostat JRT-100 installation manual