JANUS INTERNATIONAL Noke Screen User manual
INTRODUCTION
1
Before Starting
This installation guide provides instructions for installing a Nokē Screen in various settings
such as pedestrian gates, parking entries, and interior pedestals. The Nokē Screen controls
existing electronic locks. This guide is intended for licensed electricians and trained
technicians only.
Make sure you have received the parts listed below--contact your dealer for any missing
parts. The Nokē Screen also includes a software application (app) which can be downloaded
from noke.app.
Parts
Note: The Backplate is delivered with a Mylar film over the Mounting Holes for additional
waterproofing. Before mounting the Backplate to a shroud or wall, the installers will need to remove
this Mylar film.
Nokē Screen
Backplate
Mounting
Screws
Torx
Wrench
Anchors
Torx
Screws
Mounting Holes
SPECIFICATIONS
2
Dimensions
2in. x 0.8in. x 5in. (5cm. x 2cm. x 12.7cm)
Material
Polished Zinc
Connectivity
Bluetooth enabled, WiFi
Power
12V - 24V DC input (requires 2 Amp capable), PoE
Backup Battery
None (backup from power supply switch)
Lock Activation
850mA / 0.01-25 Sec.
Operating Temperature
-22°F to 140°F
(-30°C to 60°C)
Water Resistance Rating
IPX6
Buttons
Backlit for visibility
Alerts
Multi-color LED indicator and auditory sounds
INSTALLATION
3
Installing the Backplate
Before drilling into walls, make sure there are no water or electrical lines in the way. For wall
mounting, use a pencil to trace the desired back plate holes onto the wall. Then, drill the
holes in the wall and set the anchors.
If mounting on any masonry exterior walls, use machine screws for metal plates and toggle
screws for interior drywall. Check that the bottom tabs on the back plate are facing away
from the wall. Also, make sure the wall hole for the electrical power lines up with the large
center hole in the back plate.
Note: Installers need to fill any gaps in the screw holes (illustrated in red) to create a waterproof seal.
Also, make sure you remove outer stickers from waterproofing sticker.
Screw
Backplate
Wiring
Tabs
Wall
Anchor
Because the Backplate is also
a heatsink, these upper and
lower holes need to be clear
of silicone and debris. By
keeping these holes clear,
natural convention can occur.
INITIALIZATION
4
Wiring
When using PoE for power and data, connect the CAT6 into the control board port as
shown below.
1. No devices other than Nokēproducts should be plugged into the switch.
2. Use approved conduit only--never run high voltage inside. Always adhere to all local building
and electrical codes.
3. If there are any discrepancies between your local building codes and this manual, always
adhere to local codes, which take precedence.
NokēScreen
Control Board
Cat6
Line
Power Board
(Close Up)
Entry
Point
INITIALIZATION
5
When not using PoE for power and data, use an Altronix power supply to power Nokē
Screen. Data will need to be provided via WiFi. First, connect the power supply wire (12V-
24V DC) and both the ground (GND) and earth ground (ESD GND) wires to their relay push
pin connectors on the relay board, and then insert the relay board into the control board.
(Use only 18-gauge, 2 conductor wire.)
Connect wires coming from the entry point (or gate) to the common (COM) and either
normally open (NO) or normally closed (NC) pins on the power board. Extra connectors are
provided on the power board to connect and control additional electrical locks to the Nokē
Screen.
Power Board
(Close Up)
NokēScreen
Control Board
Note: Gate wiring can
be installed into NC_1,
depending upon the type
of entry being used.
+24v DC
Ground
Entry
Point
INITIALIZATION
6
Setting Up the Application
To initialize the Nokē Screen, you can either gather information from the unit and submit it
online or use the Nokē Smart Entry mobile device application (available on Google
Play/Apple stores). The website is: www.smartentry.noke.com.
Before initializing the device, you need a Nokē login and password (see your Janus
International Project Manager), and the device must be connected to a PoE cable or 12V-
24V power supply and data line (Ethernet cable).
To initialize your Nokē Screen,
1. Once the device is powered up properly, the Welcome Screen displays.
2. Press Con the keypad to access the Test/Diagnostics menu.
3. Press 9on the keypad to display the device information.
4. Take a photo of the device information since this initialization screen only appears this one
time.
5. Press 0on the keypad to display the QR code.
6. Log in to the Storage Smart Entry app and navigate to the device site. (If you have access to
multiple sites, an arrow next to the site name appears on the Home screen.)
INITIALIZATION
7
7. Press Upload.
8. Go to the menu page (icon on the upper- right corner of the app) and press Add Gateway.
9. Name the gateway with a similar name to the device name.
10. Use the Comments section to record how the device was wired (for example, PoE, 12V D.C.
etc.).
INITIALIZATION
8
11. Press Save and Finish.
INITIALIZATION
9
12. Press the +button in the upper right-hand corner of the app to add your device.
13. Using the app, scan the QR code on the Nokē Screen display.
14. After scanning, name your device and select what type of entry it controls (for example, gate,
door, elevator, sliding door, etc.). Consider using a logical name or consult with a facility
manager when naming the device.
Table of contents
