Jawbone UP2 Manual

6/29/2015 https://help.jawbone.com/articles/en_US/PKB_Article/setupup2
https://help.jawbone.com/articles/en_US/PKB_Article/setupup2 1/7
JAWBONESUPPORT>SETUP UP2
Setup UP2
Step 1: Charge your band*
1. Your band takes approximately one hour to fully
charge. Connect the charging cable to your band by aligning the pins on the
charger with the band. A magnet will hold the charger in place.
2. Insert the charging cable into the USB drive on
your computer or a standard USB wall adapter.
3. Icons on the face of the band will light up and
pulse while the band is charging.

6/29/2015 https://help.jawbone.com/articles/en_US/PKB_Article/setupup2
https://help.jawbone.com/articles/en_US/PKB_Article/setupup2 2/7
4. When the band is fully charged the icons will stop
pulsing and the runner icon will glow solid.
* Band shown is an UP3.
Step 2: Size it for your wrist*
1. The band should be worn on your non-dominant
wrist. Place the band on your wrist and rest your wrist on a flat surface.
2. Thread the strap through the loop and tighten the
strap so that all of the sensors are touching your skin. The band should be snug,
but not tight.

6/29/2015 https://help.jawbone.com/articles/en_US/PKB_Article/setupup2
https://help.jawbone.com/articles/en_US/PKB_Article/setupup2 3/7
3. Use your finger to hold the loop in place and fold
the strap over. Note where the clasp lands.
4. Remove the band and adjust the buckle by sliding
it in place.
5. Put the band back on and insert the clasp into the
buckle.
*Band shown is an UP3.
Step 3: Check your band's mode to get started*

6/29/2015 https://help.jawbone.com/articles/en_US/PKB_Article/setupup2
https://help.jawbone.com/articles/en_US/PKB_Article/setupup2 4/7
1. You must be wearing your band to activate it
andchange modes.
2. Rapidly tap the top band surface until it wakes.
3. The runner icon will glow to indicate you are in
Awake mode.
4. A moon icon will glow to indicate you are in Sleep
mode.

6/29/2015 https://help.jawbone.com/articles/en_US/PKB_Article/setupup2
https://help.jawbone.com/articles/en_US/PKB_Article/setupup2 5/7
5. Touch and hold the surface of the band to switch
modes, the band will vibrate and the runner or moon icon, depending on which
mode you are in, will light up.
6. Set your band to Awake mode to track your
daytime activity and steps.
*Band shown is an UP3.
Step 4: Get the UP App

6/29/2015 https://help.jawbone.com/articles/en_US/PKB_Article/setupup2
https://help.jawbone.com/articles/en_US/PKB_Article/setupup2 6/7
Company
Aboutus
News&Press
Careers
Blog
Shop
Store
RefurbishedProducts
RetailPartners
CorporateSales
Support
CONTACT SUPPORT
1-800-JAWBONE / 1-800-529-2663
Contact us
Monday - Sunday, 6AM-7PM (Pacific)
Jawbone Customer Service is closed in observance of all major US Holidays

6/29/2015 https://help.jawbone.com/articles/en_US/PKB_Article/setupup2
https://help.jawbone.com/articles/en_US/PKB_Article/setupup2 7/7
Support
Contactus
Get the latest news
©2014Jawbone.Allrightsreserved.Seeourtermsofuse.
Enteremailaddress