Jaycar LA5584 User manual

Wireless Contact Sensor
38mm
66mm
15mm
38mm
SET
1
4
2
3
5
Installation Guide
Overview
Name: Wireless Contact Sensor
Battery Type: CR2032 x 1
Dimension: 34 x 65 x 13 mm (w/o bracket)
34 x 65 x 15 mm (w/ bracket)
Magnet: 12 x 39 x 10 mm
Names of Parts
1. Status LED
2. Reed Switch Indicator
3. Battery Holder
Features
Burglar-Proof – once the device is triggered, the device will automatically send the signal wirelessly to the Gateway for
monitoring the door/window status.
Power Saving – one coin cell battery can be used for more than 1 year. It is also equipped with the low battery alert function.
Easy Setup – simply press the SET button on the device to join the system.
RSSI Functionality – the signal strength is indicated by its LED indicator and behavior.
Tamper-Proof Functionality – the function will be enabled when the device joins to the system.If the device is moved, it will
automatically send a signal to the Gateway.
4. SET Button
5. Bracket
Installation
Device Installation and Binding
1. Install the battery into the battery holder.
Attention: Make sure the positive (+) pole is facing up.
Status LED Color and Behavior
Good
Normal
Poor
No Signal
Blinks green (very quickly) for 15 seconds.
Blinks green (quickly) for 15 seconds.
Blinks green (slowly) for 15 seconds. (not recommended)
Blinks red for 3 seconds and then turns off. (not recommended)
CAUTION
RISK OF EXPLOSION IF BATTERY IS
REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES
ACCORDING TO THE INSTRUCTIONS.
2. Short press the SET button at the back of the
Gateway or Router (Power Switching).Then
short press the SET button on the device.
The Gateway/Router and the device are
joining as both LED indicators blink (around
15 seconds).Wait for few seconds until both
LED indicators are turned off, indicating the
device binding process is successful.
Open the battery holder. Insert battery. Close the battery holder.
Mount the bracket. Install it onto the bracket.
Note: If the device binding process is failed, both LED indicators on those joined devices will light red once after blinking.
3. Mount the bracket and magnet on the door/window.
Device Deletion
To remove the device binding, press the SET button for 5 seconds.The LED
indicator blinks green and then turns off. After few seconds, the LED indicator
blinks red and then turns off again, indicating the deletion process is complete.
Checking Device Received Signal Strength Indication (RSSI)
Short press the SET button on the device twice.
The signal strength is indicated by its LED indicator.

10mm
38mm 28mm
Notice
Mount the bracket on the frame side of the door or
window, and then put the reed on the bracket.
Troubleshooting
Problem Solution
Confidential. All Rights Reserved
The LED indicator lights red when
linking to the system.
Cannot link to the system.
a. Make sure the battery has been properly installed and its power is
adequate.
b. Reset to factory default, and re-join to the system.
c. If the problem persists, please contact your local distributor.
Check the wireless signal via RSSI and the distance between device and
Gateway/Router (line of sight) is 50 meters (max.). If there is any
obstructions (i.e. walls or metal objects) between the devices, the
distance will be shorter. Users can move the device closer or add a Router,
then try again.
Specifications
Wireless Contact Sensor
Electrical Specifications
Transmit Frequency
Operation Range
Operation Voltage
Battery Type
Battery Life
LED Indicator
Environmental Requirement
Operating Temperature
Storage Temperature
Humidity
Mechanical Specifications
Dimension (W x H x D)
Weight (without battery)
Weight (with battery)
2.4GHz ISM band, IEEE802.15.4: 2405 ~ 2480MHz
Up to 50 meters (LOS)
3.0 VDC
CR2032 x 1
Up to 1 year
Red/Green
0°C to 50°C
-10°C to 55°C
90% RH Max., Non-Condensing
34 x 65 x 13 mm (without bracket)
34 x 65 x 15 mm (with bracket)
Magnet: 12 x 39 x 10 mm
24g / Magnet: 6g
27g
Place the magnet on the door or window side. Align the arrow
point of the reed by less than 10mm distance.Then stick on it.
Note: Due to tamper-proof design, please make sure the
installation is stable to avoid any false alarm.