Jaypro Sports FSG-2 User manual

- - Page 1of 6
-- FSG-2 --
Installation Instructions
Call Jaypro Sports Equipment at 1-800-243-0533
during regular business hours for technical support.
www.jaypro.com

- - Page 2of 6
FSG-2
PARTS LIST (QTY: SINGLE UNIT)
ITEM
IMAGE
DESCRIPTION
QTY
1
BOTTOM BACKSTAY LEFT
FSG67910-3
1
2
BOTTOM BACKSTAY RIGHT
FSG67910-4
1
3
SQUARE CROSSBAR
FSG67910-6
1
4
FUTSAL GOAL UPRIGHT
FSG67910-2
2
5
TOP CROSSBAR
FSG67910-5
1
6
BACKSTAY 1.90 DIA
FSG-BS1
2
7
FUTSAL GOAL REPLACEMENT NET
FSG67910N (COMES IN COLOR WHITE)
1
8
Classic Cast Corner –Machined
SG-L
2
9
3/8-16 UNC-Nylon Lock Nut, SS
HN5003
8
10
3/8-16 x 3 HEX BUTTON SCREW, SS
HS5203
6
11
2" x 2" BLACK SQUARE TUBE CAP
EP0018
2
12
3/8" FLT SAE, SS
HW2151
8
13
3/8" SPLIT LOCK WASHER, SS
HW2152
8
14
3/8-16 x 3/4 HEX BUTTON SCREW, SS
HS5228
8
15
3/8-16 x 2-1/2 HEX BUTTON SCREW, SS
HS5202
2
16
VELCRO (20 COUNT@15 in)
SINT-20
1
17
NET CLIPS
ENC-824
1/2

- - Page 3of 6
IMPORTANT NOTICE:
1) BEFORE EACH USE CHECK EQUIPMENT FOR PROPER CONNECTING
HARDWARE AND STRUCTURAL INTEGRITY. REPLACE DAMAGED OR
MISSING HARDWARE IMMEDIATELY.
2) NEVER ALLOW ANYONE TO CLIMB OR HANG ON THE NET OR GOAL
FRAME. AS SERIOUS INJURY OR DAMAGE TO THE EQUIPMENT MAY
OCCUR.
3) USE OF THIS EQUIPMENT OTHER THAN INTENDED, MAY BE
HAZARDOUS.
4) ALTERATION OR MODIFICATION OF THIS EQUIPMENT MAY BE
HAZARDOUS AND RESULT IN INJURY. FOR REPAIR OR
REPLACEMENT, CONTACT YOUR DEALER OR JAYPRO SPORTS.
Tools Require:
1
Rubber Mallet
1
9/16" Socket Wrench or Box Wrench
1
7/32" Allen Wrench
oUnpack all parts and check against parts list to ensure that all have been
included.
oInspect all parts for damage. Report any damages to the trucking
company.
oTools required: tape measure, step ladder
* Extra screws are included, discard or stow away as needed.

- - Page 4of 6
ASSEMBLY (REQUIRES 2 PEOPLE):
1) Unpack all parts and check against parts list to ensure that all parts have been included.
2) inspect for damage. Report all damages to trucking company.
3) Lay parts out on clean dry floor as shown in figure 1.
4) Assemble corner (item 8) with upright (item 4) do not add hardware at this time. See
detail a.
5) Install end cap using rubber mallet to bottom backstay (item 1 & 2) see detail b.
6) Assemble the backstay (item 6) into the hub of the corner fitting (item 8) using 2-1/2"
long screw.
7) Assemble bottom backstay (item 1) to assembled corner and upright. See detail c, do
not add hardware.
8) With the help of a second person assemble the backstay (item 6) you may need to lift
up on the bottom backstay to fit together. Now add the bolts, washers or nuts as shown in
details a, c, and d; do not tighten hardware completely yet.
9) Repeat steps 4, 5, 6 and 8 to assemble upright on opposite side.

- - Page 5of 6
10) Slide top crossbar (item 5) into corner and install hardware shown in detail e, do not
tighten bolts completely.
11) Assemble opposite upright to crossbar with hardware shown in detail e and again do
not tighten bolts completely.
12) With the help of a second person assemble the square bottom crossbar (item 3) to the
bottom backstays using hardware shown. See detail f again do not tighten the hardware
completely.
13) Cut and apply anti-skid pad to bottom surfaces of upright, bottom backstays and
square bottom crossbar.
14) With the help of a second person stand the goal up-right.

- - Page 6of 6
15) Square the frame and tighten all hardware. Start by aligning the corner piece with the
upright extrusion and closing any gap between the corner and the upright. Now tighten
the two screws furthest from the corner hub. Once they are secure you can tighten the
bolt closest to the corner hub. Follow this same procedure for securing the crossbar to
the corner piece. Once the corners are secured the rest of the goal hardware can be
tightened down.
16) Layout net and identify corners. Drape net over or under frame and attach using
velcro strips cut at 12 inches long each and spaced approximately 12 inches apart.