Jaypro Sports Elite 6600 User manual

5/14/19
www.jayprosports.com
JAYPRO ELITE SERIES ADJUSTABLE PORTABLE BACKSTOPS
Installation and Operating Instructions
Applicable Part Numbers/Models:
PBEL66: Jaypro Elite 6600
PBEL96: Jaypro Elite 9600

ELITE Series Adjustable Portable Backstop Instructions
- 1 of 32-
JSL-Inst039
www.jayprosports.com
Table of Contents
 Safety ..............................................................................................................1 
 Specifications.................................................................................................2 
 Introduction....................................................................................................2 
 Required Tools................................................................................................3 
 Included Hardware & Components ...........................................................3 
Miscellaneous Hardware.............................................................................3 
Locating devices..........................................................................................4 
Anchor Kit (PBELKIT)......................................................................................4 
Backboard, Edge Pad & Rim......................................................................5 
Backboard & Rim hardware kit..................................................................5 
 Unpacking ......................................................................................................7 
 Backboard & Rim Installation.......................................................................9 
 Raise Backstop.............................................................................................19 
 Set Rim Height/Adjust Leveling Feet..........................................................21 
 Padding Installation.....................................................................................23 
 Lowering Backstop for Transport................................................................27 
 Installing Locating Devices.........................................................................28 
 Installing Anchor Kit .....................................................................................30 
 Spring Adjustments......................................................................................31 
 Maintenance ...............................................................................................32 
Safety
 IMPORTANT: LIFT-ASSIST SPRINGS UNDER EXTREME TENSION. DO NOT ADJUST SPRINGS
WITHOUT CONSULTING MANUAL, SEE SECTION 14 (PAGE 31).
 IMPORTANT: DO NOT REMOVE J-HOOK HOLD DOWN CLAMP OR QUICK-RELEASE PIN
UNTIL THE BACKBOARD AND RIM HAVE BEEN INSTALLED. FAILURE TO COMPLY MAY
RESULT IN SEVERE OR FATAL INJURY AS WELL AS SIGNIFICANT DAMAGE TO
SURROUNDING STRUCTURES.
 Follow all warning labels on backstops.

ELITE Series Adjustable Portable Backstop Instructions
- 2 of 32-
JSL-Inst039
www.jayprosports.com
 Do not stand directly behind uprights when raising or lowering the backstop.
 Be sure that area within 8 feet (2.5 meters) of backstop is clear of bystanders before
raising or lowering.
 Obtain assistance if lifting/lowering operation is too strenuous.
 Do not use backstop unless it is pinned at game-height using the supplied quick
release pin.
 Unit must be pinned in position using supplied quick-release pin at all times unless
raising or lowering.
 When raising or lowering, do not release handles until backstop has been pinned in
position with the supplied quick-release pin.
 Do not attempt to remove the backboard unless the unit is pinned in position with the
supplied quick-release pin.
 Do not hang on rim.
 Do not use power tools to raise or lower wheels.
 Do not use backstop for gameplay unless wheels are raised and unit is supported on feet.
 Inspect backstop for damage before and after each use.
Specifications
Extension Ballast
Standard
Backboard
Standard
Rim Total Weight
Jaypro Elite
9600 96” 1000 lbs
GBRUB-42
(42” x 72”) GBA-642 2,600 lbs
Jaypro Elite
6600 66” 800 lbs
GBRUB-42
(42” x 72”) GBA-642 2,400 lbs
Jaypro Elite
5400 54” 800 lbs
1
GBRUB-54
2
(42” x 54”) GBA-642 1,600 lbs
Introduction
This guide describes the installation and use of the ELITE Series Adjustable
Portable Backstops, models PBEL66, and PBEL96.
The sections of this guide that detail the initial setup of the backstops is
written with experienced mechanical contractors/installers in mind. If you
require additional information or support to install your backstops, please
contact the Jaypro Sports customer support team, Monday through
Friday, 8:30AM to 5:00 PM (EST), at 1-800-243-0533.
The guide is organized in the order of operations required for initial
assembly, installation, and setup. The installer is responsible to carry out
1
When shipped with 72” board (optional upgrade), 1000 lbs of ballast is included.
2
GBRUB-42 available as optional upgrade, must be specified at time of order

ELITE Series Adjustable Portable Backstop Instructions
- 3 of 32-
JSL-Inst039
www.jayprosports.com
the procedures described in sections 1 through 13. Section 14 describes
the procedure for adjusting the lift-assist springs and should only be used
by an experienced contractor/installer. Please contact the Jaypro Sports
customer support team, Monday through Friday, 8:30AM to 5:00 PM (EST),
at 1-800-243-0533 if assistance with locating an experienced professional is
required.
Required Tools
Before continuing, please verify that you have the following tools required
to complete the installation and setup of your Elite series adjustable
portable backstop.
 1-1/2” Open end
 Adjustable wrench (up to 1-1/2”)
 9/16” Combo wrench
 9/16” Socket
 #2 Phillips screwdriver
 Level
 7/8” Transfer punch (recommended)
 1-1/8” hole saw
 1-3/8” hole saw
 Adhesive suitable for metal-to-wood bonding
 Sandpaper, 180 – 320 grit
Included Hardware & Components
Before continuing, please verify that you have all the required hardware
(included w/ unit) for installation and setup. If any of the following items
are missing, contact the Jaypro Sports customer support team, Monday
through Friday, 8:30AM to 5:00 PM (EST), at 1-800-243-0533.
Miscellaneous Hardware
Figure 5-1: Quick-release pin for height adjustment (1X)

ELITE Series Adjustable Portable Backstop Instructions
- 4 of 32-
JSL-Inst039
www.jayprosports.com
Locating devices
Figure 5-2: Locator Pin Bushing (2X) Figure 5-3: Locator Pin (2X) Figure 5-4: Wire-snap safety
pin for locator pins (2X)
Anchor Kit (PBELKIT)
3
Figure 5-5: FP-89 Floor Anchor (1X) Figure 5-6: Cover plate
(for flaoting wood floors only)
Figure 5-7: ½"-13 Eyebolt w/
shoulder (1X) Figure 5-8: Shackle (2X) Figure 5-9: Twisted chain (8”)
3
Included with PBEL96, optional on PBEL66, see catalog for ordering information

ELITE Series Adjustable Portable Backstop Instructions
- 5 of 32-
JSL-Inst039
www.jayprosports.com
Backboard, Edge Pad & Rim
Figure 5-10: Breakaway Rim (1X,
model varies)
Figure 5-11: Backboard
(72" board supplied w/ PBEL96 &
PBEL66)
Figure 5-12: Edge pad
(1X, model varies)
Figure 5-13: Adjustable backboard support arm (2X).
Backboard & Rim hardware kit
Figure 5-14: Wire Net Tie (1X, incl. with goal) Figure 5-15: Wrench & Adjust Pin (1X Each, incl. with
goal)
Figure 5-16: 3/8” x 4-1/2” Hex Bolt (4X) Figure 5-17: 3/8”-16 x 1-1/2” Hex Bolt (2X)
Figure 5-18: 3/8”-16 Flanged Hex Nuts (10X) Figure 5-19: 3/8” Flat Washer (12X)
Note: Disregard fasteners included with the goal.

ELITE Series Adjustable Portable Backstop Instructions
- 6 of 32-
JSL-Inst039
www.jayprosports.com
Figure 5-20: 3/8”-16 x 1” Carriage Bolt (4X) Figure 5-21: Clevis bracket (4X)
Figure 5-22: 5/8”-11 Nylon Hex Nuts (4X) Figure 5-23: 5/8” Flat Washer (24X)
Figure 5-24: 5/8”-11 x 2-1/2” Hex Bolt (4X)
Figure 5-25: 5/8”-11 x 6” Left Thread Rod End (2X) Figure 5-26: 5/8”-11 x 6” Right Thread Rod End (2X)
Figure 5-27: 5/8”-11 Left Thread Jam Nut (2X) Figure 5-28: 5/8”-11 Right Thread Jam Nut (2X)

ELITE Series Adjustable Portable Backstop Instructions
- 7 of 32-
JSL-Inst039
www.jayprosports.com
Unpacking
IMPORTANT: DO NOT REMOVE J-HOOK HOLD DOWN CLAMP, CARGO STRAP, OR QUICK
RELEASE PIN UNTIL THE BACKBOARD AND RIM HAVE BEEN INSTALLED.
FAILURE TO COMPLY MAY RESULT IN SEVERE OR FATAL
INJURY AS WELL AS SIGNIFICANT DAMAGE TO SURROUNDING STRUCTURES.
! WARNING !
J-HOOK
QUICK PRELEASE PIN

ELITE Series Adjustable Portable Backstop Instructions
- 8 of 32-
JSL-Inst039
www.jayprosports.com
1. Carefully remove any outer wrap or packaging materials.
a. Use caution when using a box cutter or other sharp objects to
avoid scratching the powder-coated surfaces.
b. Do not remove cargo straps (if installed) or j-hook until after
the backboard is completely installed.
2. Raise feet all the way with a 1-1/2” open wrench or adjustable
wrench.
a. It will be necessary to back off the jam nut that is jammed
against the underside of the frame.
b. The front of the unit should now be resting on the wheels.
c. Be careful not to loosen the nuts locking the leveling feet to
the threaded rod. Use the bottom nut on the leveling foot to
raise the leveling feet and the nut on top of the leveling to
lower the feet.
Figure 6-1: Back off Jam nut. Figure 6-2: Raise feet using 1-1/2” open wrench.
3. Carefully roll backstop off pallet or container.
WARNING: be sure that nobody is directly in front of or behind
backstop when rolling off pallet.
1) Use 1 3/8'' or adjustable wrench on the nut which is part of the leveling foot to raise the leveling feet.
2) Use 1 1/2'' of adjustable wrench on the jam nut on top of the leveling foot nut to lower the leveling feet.
1)
2)

ELITE Series Adjustable Portable Backstop Instructions
- 9 of 32-
JSL-Inst039
www.jayprosports.com
Backboard & Rim Installation
WARNING: DO NOT REMOVE J-HOOK, CARGO STRAPS (IF INSTALLED), OR QUICK-RELEASE
PIN UNTIL THE BACKBOARD AND RIM HAVE BEEN INSTALLED. FAILURE TO COMPLY MAY
RESULT IN SEVERE OR FATAL INJURY AS WELL AS SIGNIFICANT DAMAGE TO SURROUNDING
STRUCTURES.
1. Lower wheels until both 2-by-4’s on side of base are level.
2. Lower both feet by hand or using a 1-1/2” open or adjustable
wrench until they touch the ground.
3. Lock feet in place by tightening jam nuts against frame with wrench
(as in Figure 7-3).
4. Raise wheels and confirm base is still level.
Figure 7-1: Operate jack to lower wheels. Figure 7-2: Lower feet using 1-1/2” open wrench.
NOTE: LEVELING FEET WILL BE DOWN WHEN UNPACKING

ELITE Series Adjustable Portable Backstop Instructions
- 10 of 32-
JSL-Inst039
www.jayprosports.com
Figure 7-3: Lock feet w/ Jam nut. Figure 7-4: Raise wheel to level feet.
5. Assemble adjustable support arms as shown below, note left and
right hand threads. Do not force it.

ELITE Series Adjustable Portable Backstop Instructions
- 11 of 32-
JSL-Inst039
www.jayprosports.com
Figure 7-5: Backboard Support Arms
6. Support the backboard such that the mounting holes in the bottom
middle of frame are in line with the bolt pattern on the end of the
boom (Figure 7-7). Sawhorses or a forklift may be used if additional
hands are not available to help (not a one-person job).
7. Insert 3/8”-16 x 1½” hex bolts (2X), 3/8” flat washers (4X), and 3/8”
flange hex nuts (2X) into middle row of holes in backboard mount.

ELITE Series Adjustable Portable Backstop Instructions
- 12 of 32-
JSL-Inst039
www.jayprosports.com
Figure 7-6: Backstop boom.

ELITE Series Adjustable Portable Backstop Instructions
- 13 of 32-
JSL-Inst039
www.jayprosports.com
8. Level the backboard as shown below.
9. Attach both adjustable backboard support arms to the slots in
boom using the 3/8”-16 x 1” carriage bolts (2X), 3/8-16” flange nuts
(2X) as shown in below Figure 7-7. Hand-tighten the nuts; do not use
a wrench.
Figure 7-7: Install backboard support arms to slots in boom.

ELITE Series Adjustable Portable Backstop Instructions
- 14 of 32-
JSL-Inst039
www.jayprosports.com
10. Slide the bolts into the slots of the top backboard. Fasten bolts to
backboard using the 3/8”-16 x 1” carriage bolts(2X) and the 3/8”
flanged nuts. Wrench tighten all nuts attaching support arms to
boom and backboard.
11. Check the plumbness of the backboard. If it is not plumb, twist arms
to lengthen or shorten them until the board is plumb.

ELITE Series Adjustable Portable Backstop Instructions
- 15 of 32-
JSL-Inst039
www.jayprosports.com
12. Remove front cover from supplied rim.
13. Fasten rim to board using the 3/8”-16 x 4½” carriage bolts (4X), 3/8”
flat washers (4X) and 3/8” flanged nuts (4X) as shown in Figure 7-9.
14. Attach rim to board and boom Figure 7-10.
15. Ensure that rim is level, side-to-side
4
, before fully tightening nuts.
16. Reattach front cover of rim.
17. Follow instructions included with rim to attach net.
Figure 7-8: Remove front rim cover.
4
Level rim front-to-back using adjusting bushing in board.

ELITE Series Adjustable Portable Backstop Instructions
- 16 of 32-
JSL-Inst039
www.jayprosports.com
Figure 7-9: Insert hardware.
Figure 7-10: Attach rim to board and boom.
3/8” x 4½” Carriage Bolt

ELITE Series Adjustable Portable Backstop Instructions
- 17 of 32-
JSL-Inst039
www.jayprosports.com
Adjust hex nuts on
backboard to plumb rim.
Make sure top of rim is
inline with target
Rim
Target

ELITE Series Adjustable Portable Backstop Instructions
- 18 of 32-
JSL-Inst039
www.jayprosports.com
Figure 7-11: Reattach rim cover.
Follow instructions included
with Rim to attach net.
Follow instructions included
with edge pad.

ELITE Series Adjustable Portable Backstop Instructions
- 19 of 32-
JSL-Inst039
www.jayprosports.com
Raise Backstop
WARNING: DO NOT REMOVE J-HOOK, SAFETY STRAP OR QUICK-RELEASE PIN UNLESS THE
BACKBOARD AND RIM HAVE BEEN INSTALLED. FAILURE TO COMPLY MAY RESULT IN SEVERE
OR FATAL INJURY AS WELL AS SIGNIFICANT DAMAGE TO SURROUNDING STRUCTURES.
WARNING: DO NOT STAND DIRECTLY BEHIND UPRIGHTS WHEN RAISING OR LOWERING THE
BACKSTOP. SEE Figure 8-4 FOR DETAILS ON WHERE TO SAFELY POSITION YOURSELF WHEN
RAISING/LOWERING THE BACKSTOP.
WARNING: BE SURE THAT AREA WITHIN 8 FEET (2.5 METERS) IS CLEAR OF BYSTANDERS
BEFORE RAISING OR LOWERING.
WARNING: DO NOT USE BACKSTOP UNLESS IT IS PINNED AT GAME-HEIGHT USING THE
SUPPLIED QUICK RELEASE PIN.
WARNING: UNIT MUST BE PINNED IN POSITION USING SUPPLIED QUICK-RELEASE PIN AT ALL
TIMES UNLESS RAISING OR LOWERING.
WARNING: WHEN RAISING OR LOWERING, DO NOT RELEASE HANDLES UNLESS BACKSTOP IS
PINNED IN POSITION WITH THE SUPPLIED QUICK-RELEASE PIN.
1. ONLY IF BACKBOARD HAS BEEN INSTALLED, remove quick-release pin
from height adjuster mechanism (Figure 8-1).
Figure 8-1: Height adjuster mechanism
2. Carefully remove J-Hook by removing nut as shown in figure below.
a. Pay extra attention when removing the J-Hook to make sure
that the backstop does not begin to rise on its own. If it does,
retighten J-Hook, reinstall the quick-release pin and refer to
section 14 for details on how to adjust the springs
5
.
5
Spring tension is preset at factory. Under normal circumstances, spring adjustment is not
typically necessary.