Jaypro Sports BBC-QS70 User manual

Rev - D Page 1 of 9
--- BBC-QS70 ---
(Quick Set-Up Batting Tunnel)
Installation Instructions
Call Jaypro Sports Equipment at 1-800-243-0533 during
regular business hours for technical support.
www.jaypro.com
OPTIONAL WALL MOUNTING KIT
MODEL #: BBC-WLKT
OPTIONAL NET STORAGE CART
MODEL #: TENINJA-CART
OPTIONAL WALL HOISTING KIT
MODEL #: BBC-QSKIT1

Rev - D Page 2 of 9
JAYPRO SPORTS
BBC-QS70, INDOOR QUICK SET-UP BATTING TUNNEL KIT
IMPORTANT NOTICE:
1) DO NOT SET CAGE OR NET TOO CLOSE TO WALLS, COLUMNS, LOW CEILINGS
OR ANY SOLID OBJECT WHERE BALLS CAN STRIKE AND BOUND BACK. CAGE
OR NET SHOULD BE AT LEAST 4 FEET FROM ALL BYSTANDERS, CEILINGS,
WALLS OR SOLID OBJECTS.
2) SPECTATORS MUST NOT STAND IN BACK OR NEAR SIDES OF CAGE OR NET
WHILE BEING USED FOR BATTING PRACTICE.
3) ALTERATION OR MODIFICATION OF THIS EQUIPMENT MAY BE HAZARDOUS
AND RESULT IN INJURY. FOR REPAIR OR REPLACEMENT, CONTACT YOUR
DEALER OR JAYPRO SPORTS.
4) CAUTION: DO NOT OVER TIGHT THE CABLES, AS EXTREME LOADING WILL BE
PLACED ON THE WALL OR END STRUCTURE.
PRODUCT DESCRIPTION:
The BBC-QS70, quick set-up batting tunnel kit is designed to attach to the walls of a gym. The
distance between walls should not exceed 120 ft and must be a minimum of 85 ft. During set-up the
net easily attaches to three (3) pre-installed polyester lines coming off of each wall. One wall will
have three fixed length lines, while the other wall will contain the hoisting lines.
There are six wall attachments that need to be made, three on each wall. Because there are many
different types of wall construction, additional wall anchors may be required depending on your type
of building. Six (6) 3/8” eyebolts are provided for basic wall anchoring. These eyebolts can be
directly installed in the metal building structure, existing wall blocking, or used in conjunction with
double expansion anchors, in solid concrete walls.
If attaching to standard CMU block or stud constructed walls, it is recommended that a wood
stringer wall mounting kit be used (model number BBC-WLKT), purchased separately. This kit
includes six (6) attractive polyurethane finished 24” long, 2” x 8” stringers and mounting plates that
are easy to install and help spread the load across multiple CMU blocks or other wall types. Studded
walls will required that internal blocking be installed to help provide anchor points and spread the
load across multiple studs.
An optional Supplemental Wall Hoisting Kit (BBC-QSKIT1) is available, that can provide added
flexibility on the end of the tunnel opposite the main hoisting lines. The kit can be used if the anchor
lines are too short to access from the floor, or to provide added tension if the hoist end is bottomed out.

Rev - D Page 3 of 9
ASSEMBLY INSTRUCTIONS
TOOLS REQUIRED:
(1) Box Wrench Set
(1) Electric Drill or Hammer Drill
(1) Appropriate drill set (depends on wall construction)
(1) Ladder or Scissor Lift
(1) Tape measure
•Unpack all parts and check against parts list to ensure that all have been included.
•Inspect all parts for damage. Report any damages to the trucking company.
ITEM
DESCRIPTION
BBC-QS70
1
70’ x 14’ x 14’ BBC NET (P/N: BBC-701414)
1
2
5/16” x 300 FT LONG BLACK BRAIDED ROPE
1
3
PULLEY BLOCK w/ CAM CLEAT (P/N: HM6568A)
3
4
SNAP HOOK (P/N: HM5013)
12
5
D-RING (P/N: HM240)
6
6
SWIVEL PULLEY (P/N: HM6226)
3
7
6” WIDE STEEL CLEAT (P/N: HM6331)
6
8
1/4”-20 x 2 3/4”HEX CAP SCREW
12
9
1/4” WASHER
12
10
1/4”-20 NYLON LOCK NUT
12
11
3/8”-16 x 3” EYEBOLT
6
12
3/8”-16 HEX NUT
6
13
3/8” LOCK WASHER
6
14
3/8” FLAT WASHER
12
QTY

Rev - D Page 4 of 9
1) Mark the location of the cable anchor as shown in the diagram below.
Anchor Point Locations on Building Wall (Both Ends)
Note: The height of the cables should be set at about 9” below the overall height of the net. This
will place about 12” of net on the floor to capture the balls.

Rev - D Page 5 of 9
2) Install the wall anchors on both sides of the gym, as shown below. Follow the appropriate
figure for your building type. Note: if optional wall mounting kit (BBC-WLKT) is
purchased; please see installation instructions that come with it.
Figure 1: Standard Building Attachment - For Metal Structure and Wood Blocking
Figure 2: Standard Building Attachment - For Solid Concrete Walls
(Double Expansion Shield Anchors Not Provided)
Figure 3: Optional Wall Mounting Kit –For CMU and Studded Walls
(Alternate Wall Anchors Required)

Rev - D Page 6 of 9
3) Make up and install the three fixed end lines. Based on the desired distance off the wall, cut
three equal lengths of 5/16” black braided rope and tie two snap hooks to each end. Attach
the three lines to the wall anchors.
Figure 4: Fixed End Support Lines
(Line Length Base on Desired Distance off the Wall)
4) Make up and install the three hoisting lines. The approximate length of each line will equal
twice the distance off the wall, plus 25 ft. Tie one end of the rope to the bottom of the pulley
block and then pass it through the swivel pulley. Next pass the rope through the pulley black
and cam cleat, as shown in Figure 5. Attach the three hoisting lines to the wall anchors.
Figure 5: Hoisting Lines
(The Approximate Line Length Will Equal Twice The Distance Off The Wall, Plus 25 ft)

Rev - D Page 7 of 9
5) Make up the six leads on the end of the net as shown in Figure 6.
Figure 6: Assemble Net Leads
(6 Places on Netting)
6) Attach one end of the net to the fixed end lines. Feed out the three hoisting lines and attach
each to the other end of the net. Evenly hoist the net up into position, making sure to apply
equal tension to all three lines.
Figure 7: Assemble Suspended Net Leads
Note: Top cords should be
anchored to the net in all six
locations. Do not undo knots
securing the cords to the net body.

Rev - D Page 8 of 9
7) Make any necessary adjustments.
8) Install the Six, 6” wide steel cleats beneath each of the six lines, see Figure 8 & 9. It is
recommended that the cleats be installed at a height of at least 7 ft above the floor.
Figure 8: Standard Building Attachment - For Metal Structure and Wood Blocking
Figure 9: Standard Building Attachment on Fixed End - For Solid Concrete Walls
(Double Expansion Shield Not Provided)
9) Lower the net by releasing each hoisting line from the cam cleat. Before removing the net go
back and cut off any excess rope from the hoisting line. Tie a knot in the very end of each
line to prevent the line from accidentally passing through the pulley block.
10)Remove the net and store in a suitable container. See optional net storage cart (TENINJA-CART).
11)Gather all lines and hang them from their respective wall cleat.

Rev - D Page 9 of 9
OPTIONAL KITS AND HARDWARE:
MODEL #: BBC-WLKT
WALL MOUNTING KIT: (QTY: 6) Wood
stringers and mounting plates for attaching to
CMU block and concrete walls.
MODEL #: TENINJA-CART: Net storage cart.
MODEL #: BBC-QSKIT1
Supplemental Wall Hoisting Kit
To be used if the anchor lines are too short to
access from the floor, or to provide added tension
if the hoist end is bottomed out.