JBL CS80 User manual

Cinema Sound
CS80
CS480 Amplifier/Subwoofer
SERVICE MANUAL
JBL Consumer Products
250 Crossways Park Dr.
Woodbury, New York 11797 Rev0 4/2007

Note: The CS80 subwoofer is part of the CS480 system
Satellite loudspeakers CS480 order JBL part# CS400SATBG-E
Center channel CS480 order JBL part# CS600CENBG-E
- CONTENTS -
BASIC SPECIFICATIONS……………….….….….….…………….1
DETAILED SPECIFICATIONS ……..…………….……………..2
PACKAGING……………………………………….........................4
CONTROLS & CONNECTIONS.……………… …...…….……...5
OPERATION ………….……………………………..…………….6
EXPLODED VIEW/PARTS LIST……………...............................7
TEST SET-UP AND PROCEDURE……..…………….………….8
BLOCK DIAGRAM..…………………………………………………9
BASIC TROUBLESHOOTING…..…………….…..…..….……...11
120V ELECTRICAL PARTS LIST …………….…….…………..12
PCB DRAWINGS………………..………………………………...16
INTEGRATED CIRCUIT/TRANSISTOR PINOUTS…………..22
120V SCHEMATICS.……….……………….………..…. ………23
BASIC SPECIFICATIONS
CS80 Subwoofer
Frequency Response (– 6dB): 35Hz – 160Hz
Amplifier Output: 125W RMS/250W Peak†
Driver: 8" (203mm)
Dimensions (H x W x D, including feet): 16-1/4" x 12" x 13-5/8" (413mm x 305mm x 346mm)
Weight: 29 lb (13.2kg)
† The Peak Dynamic Power is measured by recording the highest center-to-peak voltage measured across the output of a resistive
load equal to minimum impedance of the transducer, using a 50Hz sine wave burst, 3 cycles on, 17 cycles off.
Occasional refinements may be made to existing products without notice but will always meet or exceed original
specifications unless otherwise stated
1
CS80 (CS480 Subwoofer)

CS80SUB 125W Powered Sub/ Plate Amp
LINE VOLTAGE
Y
es/No Hi/Lo Line Unit Notes
US 120VAC/60Hz Yes 108-132 Vrms Normal Operation
EU 230VAC/50-60Hz Yes 207-254 Vrms Normal Operation Normal operation, MOMS required
Parameter Specification Unit QA Test Limits Conditions Notes
Amp Section
Type (120V Model) AB AB N/A 120V System is Class AB
Type (230V Model) G H N/A 230V System is Class G
Load Impedance (woofer) 4 Ohms N/A Minimum
Woofer Size 8 in N/A Reference
System average impedance 8.22 Ohms N/A 10-500 Hz
Rated Output Power 120V 100 Watts 95 @ Nominal input voltage
Rated Output Power 230V 105 Watts 100 @ Nominal input voltage
Average value - RMS Dynamic
power 98 Watts Reference @ Nominal input voltage
3/20 50 Hz Burst unit driven 6dB above the
sensitivity to drive it into max power,
measured value is the average of the 4 first
consecutive peaks
Dynamic power Highest Peak 121 Watts Reference @ Nominal input voltage Highest RMS of the first 4 consecutive
peaks
THD@ Rated Power 0.5 % 1 22K filter
THD @ 1 Watt 0.1 % 0.3 22K filter
DC Offset 10 mV-DC 50 @ Speaker Output
Damping factor >150 DF 100 Measured at amplifier board speaker out
terminals, Output power 90 Watts THD <
0.1 %
Input Sensitivity
Input Frequency 50 Hz 50 Nominal Freq.
Line Input (L&R) 14.4 mVrms ±2dB To 1 Watt Single input driven 1 input driven
LFE Input 9 mVrms ±2dB To 1 Watt LFE input driven only
System Gain-LR input 42.85 dB ±2dB Gain=130 Single input driven L or R
Signal to Noise
SNR-A-Weighted 90 dBA 85 To Rated power A-Weighting filter
SNR-unweighted 85 dBr 80 To Rated power 22KHz filter
SNR @ 1W-unweighted 65 dBr 60 To 1 Watt 22KHz filter
Residual Noise Floor 1 mVrms(max) 1.5 Volume @max, w/ A/P Swept Bandpass
Measurement (Line freq.+ harmonics) Refer to AP Graph
Input Impedance
Line input L&R , LFE >10 K ohms N/A Nominal over the audio BW Reference only
Filters
Low Pass (fixed or variable) Variable -- ±2dB
Subsonic filter (HPF) Hz ±2dB
Limiter
(y
es/no
)
YES -- N/A
Features
LFE Input YES Functional BW Limited to 500 Hz, refer to ECR00031
Volume pot Taper (lin/log) LOG -- Functional
ATO YES Functional
Input Configuration
Line In (L,R) L ,R -- Functional RCA inputs: RED-WHT, L , R Summed to
Mono
Line level in LFE LFE Functional Single connector
Signal Sensing (ATO)
Auto-Turn-On (yes/no) YES -- Functional
ATO Input Frequency 50 Hz Functional
ATO Level Line Level in (L,R, L
F
1.5 mV Functional 2mV@50Hz into Line Input w/ 1 ch.
driven
ATO Turn-on time < 1 Sec Functional Amp connected and AC on, then input
signal applied
Auto Mute/ Turn-OFF Time 15 minutes Functional T before muting, after signal is removed Auto turn of time (T) must be 5 > T <15
Power on Delay time 3 sec. Functional AC Power Applied
2
CS80 (CS480 Subwoofer)

Parameter Specification Unit QA Test Limits Conditions Notes
Transients/Pops
ATO Transient 5 mV-peak 10 @ Speaker Outputs
Turn-on Transient 50 mV-peak 100 @ Speaker Outputs AC Line cycled from OFF to ON
Turn-off Transient 50 mV-peak 100 @ Speaker Outputs AC Line cycled from ON to OFF
Efficienc
y
Stand-by Input Power 12 Watts 13 @ nom. line voltage Unit active, no
signal applied (Green LED)
Maximum allowable input power under
nominal Input voltage and frequency, HOT
or COLD operation.
Power Cons/Amps.@rated
power 120V Model 192 / 1.89 Watts/Amps 195 / 1.90 @ 120V-60 Hz (Nom.line voltage) 100 Watts @ 4 Ohms nominal line voltage
Power Cons/Amps.@rated
power230V Model 208 / 1.1 Watts/Amps 210 / 1.2 @ 230V-50 Hz (Nom.line voltage) 100 Watts @ 4 Ohms nominal line voltage
Protection
Short Circuit Protection YES -- Functional Direct short at output
Thermal Protection 65 deg. C -- Functional @1/8 max unclipped Power Temperature rise should not exceed 35K
rise
DC Offset Protection YES -- Functional DC present at Speaker Out leads Relay or crowbar (for driver/fire protection)
Line Fuse Rating 120VAC 2.5 Amps Type-T or Slo Blo External fuse with UL/SEMKO rated holder
230VAC 1.25 Amps Type-T or Slo Blo External fuse with UL/SEMKO rated holder
3
CS80 (CS480 Subwoofer)

CS80 (CS480 Subwoofer)
4

SUBWOOFER CONTROLS
Rear Panel
PHASE
CS80SUB
¡
™
£¢
∞
§
FUSE
T 2.5A L 250V
120V–60Hz
200Watts
1Subwoofer-Level Control
2Phase Switch
3LFE Input
4Line-Level Inputs
5Power Indicator LED
6Power Switch
Subwoofer Connections
If you have a Dolby®Digital or DTS®receiver/processor with
a low-frequency-effects (LFE) or subwoofer output:
TSS-Sub800/230
SUBWOOFER OR
LFE OUTPUT
RECEIVER/PROCESSOR
15' (4.5m)
Subwoofer
cable included
If your receiver/processor does not contain a Dolby Digital or DTS
processor but has a subwoofer output:
NOTE
:If your receiver/processor has only one sub out, you may use
either the L or R input.
15' (4.5m)
Subwoofer cable
included
TSS-Sub800/230
RECEIVER/PROCESSOR
Important!
Whenever changing cables, pulling plugs, etc., ALWAYS TURN OFF ALL
EQUIPMENT, including the subwoofer.
CS 480-120V om.qxd 12/15/06 4:43 PM Page 10
5
CS80 (CS480 Subwoofer)

OPERATION
Surround Modes
When using the CS480 in a Dolby Digital or DTS home theater system,
make sure all speakers are set to “Small”. In a Dolby Pro Logic®home
theater system, make sure the receiver’s center channel mode is set
to “Normal.”
Some Dolby Digital-equipped receivers/processors offer different
setup options for each source or surround mode (e.g., CD-stereo,
videotape, Dolby, Pro Logic). In each case, follow your equipment’s
instructions to ensure that the subwoofer output is turned on and that
the speakers are set to “Small” in each mode.
Power On
Plug your subwoofer’s AC cord into a wall outlet. Do not use the outlets
on the back of the receiver.
Initially set the Subwoofer-Level Control 1to the“MIN” position.
Turn on the subwoofer by pressing the Power Switch 6on the
rear panel.
Turn on your entire audio system and start a CD or movie soundtrack
at a moderate level.
Auto On/Standby
With the Power Switch 6in the ON position, the LED on the rear
panel 5will remain lit in green or red to indicate the ON or STANDBY
mode of the subwoofer.
RED = STANDBY (No signal detected, Amp Off)
GREEN = ON (Signal detected, Amp On)
The subwoofer will automatically enter the Standby mode after
approximately 10 minutes when no signal is detected from your
system. The subwoofer will then power on instantly when a signal
is detected. During periods of normal use, the Power Switch 6
can be left on. You may turn off the Power Switch 6for extended
periods of nonoperation, e.g., when you are away on vacation.
Adjust Level
Turn the Subwoofer-Level Control 1up about halfway.If no sound
emanates from the subwoofer, check the AC-line cord and input
cables. Are the connectors on the cables making proper contact? Is
the AC plug connected to a “live” receptacle? Has the Power Switch
6been pressed to the ON position? Once you have confirmed that
the subwoofer is active, proceed by playing a CD or DVD. Use a
selection that has ample bass information.
Set the overall volume control of the receiver/processor to a comfort-
able level. Adjust the Subwoofer-Level Control 1until you obtain
apleasing blend of bass. Bass response should not overpower the
room but rather be adjusted so there is a harmonious blend across
the entire musical range. Many users have a tendency to set the
subwoofer volume too loud, adhering to the belief that a subwoofer is
there to produce lots of bass. This is not entirely true. A subwoofer is
there to enhance bass, extending the response of the entire system
so the bass can be felt as well as heard. However, overall balance
must be maintained or the music will not sound natural. An experi-
enced listener will set the volume of the subwoofer so its impact on
bass response is always there but never obtrusive.
Phase Control
The Phase Switch 2determines whether the subwoofer speaker’s
pistonlike action moves in and out with the main speakers (0˚) or
opposite the main speakers (180˚). Proper phase adjustment depends
on several variables such as room size, subwoofer placement and
listener position. Adjust the phase switch to maximize bass output at
the listening position.
CS 480-120V om.qxd 12/15/06 4:43 PM Page 11
6
CS80 (CS480 Subwoofer)

7
CS80 (CS480 Subwoofer)

CS80 Test Set Up and Procedure
Equipment needed:
•Function/signal generator/sweep generator
•Integrated Amplifier
•Multimeter
•Speaker cables
General Unit Function (UUT = Unit Under Test)
1) From the signal generator, connect one line level (RCA) cable to the Subwoofer Line Level Input jacks L/R
on the UUT. Use a Y-cable from a mono source if necessary to connect to both inputs. Do not connect to
the single LFE input.
2) Turn the LEVEL control on the UUT to completely counterclockwise (MIN).
3) Turn on generator; adjust to 75mV, 50 Hz.
4) Plug in UUT; turn the power switch ON. LED should switch from Red to Green. Turn LEVEL control full
clockwise (MAX)
5) LED should Green; immediate and vigorous bass response should be heard and felt from port tube
opening.
6) Turn off generator, turn LEVEL control full counterclockwise (MIN), and disconnect RCA cable.
Sweep Function
1) Follow steps 1-5 above, using a sweep generator as a signal source.
2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or
any other noises. If any unusual noises are heard, remove woofers and test.
Driver Function
1) Remove woofer from cabinet; detach + and - wire clips.
2) Check DC resistance of woofer; it should be 3.4 ohms ±10%
3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier
fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V.
4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
8
CS80 (CS480 Subwoofer)

9
CS80 (CS480 Subwoofer)

10
CS80 (CS480 Subwoofer)

CS80 SUB (UL)AMP
Troubleshooting Flow Chart
no
yes
yes
yes no
yes
yes
LED red
LED light green yes yes
no
yes yes no
no
yes
yes yes
no
no
yes yes
yes
no
yes
yes
AMP no signal out
Dc voltage check ±Vcc
Check+/-15VDC
LED light green or red
Check Fuse,Transformer,
D110, etc
Check RY101,D102,Q113,Q114 etc Check Q107,Q108,Q105,
Q106,Q103,Q104,U101,etc
Check ,+VCC& -VCC
DC voltage
Check U101,Q115,Q116,R138 etc
Check Q117,118,119,D109 etc
Check,Q206,Q207,U203 etc
Check U202 pin14 signal
Check U201
pin14 signal
Test R121,R122 signal
Check P102 signal The Amp Ass’y OK, END
CheckU201,U202,VR201
VR202. etc
Check J123,J124 etc
Check limiter board C304 Check U301,R343,R344 ,
C340,Q301,Q302, etc
Set R138 to R140’S
Voltage is 0.51VDC
11
CS80 (CS480 Subwoofer)

CS80 120v Electrical parts List
Part Number Description Qty Reference Designator
Main Amp PCB
Resistors
110-14472j26-E RESISTOR 4.7K 1/4W ±5% CF 26mm (RoHS) 2 R147,R150,
110-14681j26-E RESISTOR 680Ω1/4W ±5% CF26mm (RoHS) 2 R148,R151,
110-16101j26-E RESISTOR 100Ω1/6W ±5% CF26mm (RoHS) 1 R120,
110-16102j26-E RESISTOR 1K 1/6W ±5% CF 26m (RoHS) 1 R124,
110-16103j26-E RESISTOR 10K 1/6W ±5% CF 26 (RoHS) 1 R134,
110-16105j26-E RESISTOR 1M 1/6W ±5% CF 26mm (RoHS) 1 R143,
110-16123j26-E RESISTOR 12K 1/6W ±5% CF 26mm (RoHS) 2 R135,R139,
110-16152j26-E RESISTOR 1.5K 1/6W ±5% CF 26mm (RoHS) 6 R103,R123,R136,R137,R141,R142,
110-16153j26-E RESISTOR 15K 1/6W ±5% CF 26mm (RoHS) 4 R118,R145,R152,R154
110-16154j26-E RESISTOR 150K 1/6W ±5% CF 26mm (RoHS) 1 R131,
110-16181j26-E RESISTOR 180Ω1/6W ±5% CF26mm (RoHS) 2 R111,R114,
110-16182j26-E RESISTOR 1.8K 1/6W ±5% CF 26mm (RoHS) 1 R153,
110-16223j26-E RESISTOR 22K 1/6W ±5% CF 26mm (RoHS) 3 R128,R129,R133,
110-16332j26-E RESISTOR 3.3K 1/6W ±5% CF 26mm (RoHS) 3 R106,R107,R144,
110-16392j26-E RESISTOR 3.9K 1/6W ±5% CF 26mm (RoHS) 2 R105,R108,
110-16393j26-E RESISTOR 39K 1/6W ±5% CF 26mm (RoHS) 1 R126,
110-16470j26-E RESISTOR 47Ω1/6W ±5% CF 26mm (RoHS) 4 R112,R113,R115,R116
110-16471j26-E RESISTOR 470Ω1/6W ±5% CF26mm (RoHS) 1 R140,
110-16472j26-E RESISTOR 4.7K 1/6W ±5% CF 26mm (RoHS) 3 R110,R125,R130,
110-16473j26-E RESISTOR 47K 1/6W ±5% CF 26mm (RoHS) 1 R101,
110-16560j26-E RESISTOR 56Ω1/6W ±5% CF 26mm (RoHS) 1 R117,
110-16563j26-E RESISTOR 56K 1/6W ±5% CF 26mm (RoHS) 1 R104,
110-16682j26-E RESISTOR 6.8K 1/6W ±5% CF 26mm (RoHS) 1 R109,
110-122r2j15-E RESISTOR 2.2Ω1/2W ±5% 15mm (RoHS) 1 R127,
110-20331jk2-E RESISTOR 330Ω2W ±5% 5mm(RoHS) 2 R146,R149
113-50r10j10-E RESISTOR 0.1Ω5W ±5% stand (RoHS) 2 R121,R122
114-03302m0-E RESISTOR 3K 0.3W ±20%(RoHS) 1 R138,
110-10821jk2-E RESISTOR 820Ω1W ±5% 10mm (RoHS) 1 R132,
Capacitors
130-2b102k503-E DISC CAPACITOR 1000P 50V ±10% (RoHS) 1 C116,
130-3f104z503-E DISC CAPACITOR 0.1U 50V +80/-20% (RoHS) 4 C108,C113,C115,C119
130-3f473m503-E DISC CAPACITOR 0.047U 50V ±20% (RoHS) 1 C106,
130-sl101k503-E DISC CAPACITOR 100P 50V SL ±10% (RoHS) 2 C139,C140,
132-104j503-E MYLAR CAPACITOR 0.1U 50V ±5% (RoHS) 1 C107,
132-223ja03-E MYLAR CAPACITOR 0.022uF 100V ±5% (RoHS) 4 C124,C125,C126,C128
135-3105m50-E ELECTROYTIC CAP.1U 50V ±20% (RoHS) 2 C105,C112,
135-3107m16-E ELECTROYTIC CAP.100uF 16V ±20% (RoHS) 3 C109,C117,C120,
135-3226m50-E ELECTROYTIC CAP.22U 50V ±20% (RoHS) 2 C114,C118,
135-3227m10-E ELECTROYTIC CAP.220U 10V ±20% (RoHS) 2 C129,C130,
135-3227m16-E ELECTROYTIC CAP.220U 16V ±20% (RoHS) 1 C111,
135-3476m25-E ELECTROYTIC CAP.47U 25V ±20% (RoHS) 1 C103,
132-223ja03-E MYLAR CAPACITOR 0.022uF 100V ±5% (RoHS) 2 C123,C127
135-3107m16-E ELECTROYTIC CAP.100uF 16V ±20% (RoHS) 1 C110,
135-4688m50-E ELECTROYTIC CAP.6800U/50V ±20%D25X45mm (RoHS) 2 C121,C122
Semiconductors
192-027c1815gr-E TRANSISTOR 2SC1815GR TOSHIBA(RoHS) NPN 5 Q102,Q111,Q112,Q113,Q118,
192-028a1015gr-E TRANSISTOR 2SA1015GR TOSHIBA (RoHS) PNP 2 Q114,Q116,
192-1572n5551-E *TRANSISTOR FSC 2N5551 (RoHS) NPN 2 Q103,Q109,
192-1582n5401-E TRANSISTOR FSC 2N5401 AI-PNP350V 500mA TO-92 2 Q104,Q110,
197-631n4148-E DIODE 500mW 75V 1N4148 Panjit (RoHS) 4 D101,D103,D105,D108
199-65000333g-E ZENER Diode GDZJ3.3A 500mW 3.3V 2% 26mm (RoHS) 1 D102,
199-65000623g-E ZENER DIODE GDZJ6.2B 500mW 6.2V 26mm 2% (RoHS) 2 D106,D107,
199-65001603g-E ZENER DIODE GDZJ16C 500mW 16V 26mm 2% (RoHS) 1 D109,
192-021tip35c-E TRANSISTOR TIP35C (RoHS) NPN 1 Q107,
12
CS80 (CS480 Subwoofer)

Part Number Description Qty Reference Designator
Main Amp PCB
192-022tip36c-E TRANSISTOR TIP36C (RoHS) PNP 1 Q108,
192-027c1815gr-E TRANSISTOR 2SC1815GR TOSHIBA(RoHS) 2 Q101,Q115
192-201d882y-E TRANSISTOR KSD882Y PNP 1 Q117,
192-202b772y-E TRANSISTOR KSB772Y PNP 1 Q119,
192-991d669a-E TRANSISTOR HI-SINCERITY HSD669A NPN 1 Q106,
192-992b649t-E TRANSISTOR HSB649T PNP 1 Q105,
197-00kbl405-E Bridge Diode 4A 500V KBL405(RoHS) 1 D110,
197-101n4002-E DIODE 1N4002TB (RoHS) 1 D104,
190-06m4558d-E IC OPA 4558D DUAL OP-AMP 1 U101,
Miscellaneous
162-10202001-E 26AWG 1007 200mm RED 3mm (RoHS) 1
171-udhss124d-E *relay 5A 24V UDH-SS124D(RoHS) 1 RY101,
175-1c07v01-E COUPLER 7PIN PITCH=2.5mm(RoHS) 1 P101,
175-1d02v01-E COUPLER 2PIN PITCH=3.96mm(RoHS) 1 P102,
175-1d03v01-E COUPLER 3 PIN PITCH=3.96mm JST-VH peel off PIN (RoHS) 1 P103,
193-3m2520-E *mica piece TO-3P 25x20mm (RoHS) 2 for Q107,Q108
323-AL-00020-0LAE HEAT SINK 65*32*31 aluminium 1
351-AM03014A094-E M3*14 MACHINE SCREW crossover BLACK (RoHS) 1
352-AM03008D040-E ¢3*8 B TYPE PING SCREW Crossover, BLACK (RoHS) 4
361-FE-00051-0LAE TRANSISTOR holder 14.2*8.0*5.2t=1.6mm (RoHS) 1
361-NYL-00054-0LAE TRANSISTOR sheet (SW06002) (RoHS) 2
Input/Preamp PCB
Resistors
110-16102j26-E RESISTOR 1K 1/6W ±5% CF 26mm (RoHS) 5 R213,R214,R215,R254,R253,
110-16103j26-E RESISTOR 10K 1/6W ±5% CF 26mm (RoHS) 12 R212,R216,R217,R220,R221,R222,R225,R2
28,R226,R232,R235,R240,
110-16104j26-E RESISTOR 100K 1/6W ±5% CF 26mm (RoHS) 2 R231,R266,
110-16105j26-E RESISTOR 1M 1/6W ±5% CF 26mm (RoHS) 1 R259,
110-16122j26-E RESISTOR 1.2K 1/6W ±5% CF 26mm (RoHS) 1 R264,
110-16124j26-E RESISTOR 120K 1/6W ±5% CF 26mm (RoHS) 1 R233,
110-16153j26-E RESISTOR 15K 1/6W ±5% CF 26mm (RoHS) 1 R234,
110-16154j26-E RESISTOR 150K 1/6W ±5% CF 26mm (RoHS) 1 R251,
110-16183j26-E RESISTOR 18K 1/6W ±5% CF 26mm (RoHS) 2 R262,R227,
110-16205j26-E RESISTOR 2M 1/6W ±5% CF 26m m (RoHS) 1 R257,
110-16223j26-E RESISTOR 22K 1/6W ±5% CF 26mm (RoHS) 3 R238,R250,R255,
110-16273j26-E RESISTOR 27K 1/6W ±5% CF 26mm (RoHS) 2 R223,R237,
110-16333j26-E RESISTOR 33K 1/6W ±5% CF 26mm (RoHS) 1 R249,
110-16334j26-E RESISTOR 330K 1/6W ±5% CF 26mm (RoHS) 1 R252,
110-16472j26-E RESISTOR 4.7K 1/6W ±5% CF 26mm (RoHS) 2 R258,R260,
110-16473j26-E RESISTOR 47K 1/6W ±5% CF 26mm (RoHS) 1 R219,
110-16512j26-E RESISTOR 5.1K 1/6W ±5% CF 26mm (RoHS) 3 R211,R229,R230,
110-16513j26-E RESISTOR 51K 1/6W ±5% CF 26mm (RoHS) 1 R224,
115-h503a104-E Variable RESISTOR D16 50K/1 A (RoHS) 1 VR201,
Capacitors
130-2b221k503-E DISC CAPACITOR 220P 50V ±10% (RoHS) 9 C207,C208,C210,C211,C212,C214,C220,C2
30,C249,
130-3f104z503-E DISC CAPACITOR 0.1U 50V +80/-20% (RoHS) 7 C232,C242,C244,C245,C246,C252,C254,
130-ch220k503-E DISC CAPACITOR 22PF CH 50V±10 % (RoHS) 1 C229,
132-103j503-E MYLAR CAPACITOR 0.01uF 50V ±5% (RoHS) 2 C223,C224,
132-104j503-E MYLAR CAPACITOR 0.1U 50V ±5% (RoHS) 3 C218,C221,C222,
132-223ja03-E MYLAR CAPACITOR 0.022uF 100V ±5% (RoHS) 1 C215,
132-473j503-E MYLAR CAPACITOR 0.047U 50V ±5% (RoHS) 2 C216,C217,
135-3105m50-E ELECTROYTIC CAP.1U 50V ±20% (RoHS) 1 C228,
135-3106m50-E ELECTROYTIC CAP.10uF 50V ±20% (RoHS) 8 C206,C213,C219,C231,C241,C243,C251,
C253,
13
CS80 (CS480 Subwoofer)

Part Number Description Qty Reference Designator
Input/Preamp PCB
135-3107m16-E ELECTROYTIC CAP.100uF 16V ±20% (RoHS) 2 C233,C234,
135-3226m50-E ELECTROYTIC CAP.22U 50V ±20% (RoHS) 1 C225,
Semiconductors
192-027c1815gr-E TRANSISTOR 2SC1815GR TOSHIBA (RoHS) NPN 2 Q206,Q207,
197-631n4148-E DIODE 500mW 75V 1N4148 Panjit (RoHS) 7 D201,D202,D207,D208,D211,D212,D214,
199-65000513g-E ZNR DIODE GDZJ5.1B 500mW 5.1V 2% 26mm 1N5231B 1 D213,
190-06m4558d-E IC OPA 4558D DUAL OP-AMP 1 U203,
190-16tl074cn-E I.C TL074CN ST (RoHS) QUAD OP-AMP 2 U201,U202,
195-10204hgw-E LED 204HGW 3¢(RoHS) DUAL COLOR 1 D209,
Miscellaneous
162-50159201-E WIRE ASS'Y 2PIN 150mm white/red (RoHS) 1 D209,
174-0rca326p-E JACK RCA-326 (RoHS) 1 JK202,
180-tms7210v-E SWITCH SLIDE 6PIN MS7210V(RoHS) PHASE 1 SW301,
362-FE-00041-0LAE PCB bracket 11.75*8.5*12.5H(RoHS) 1
Limiter PCB
110-16103j26-E RESISTOR 10K 1/6W ±5% CF 26mm (RoHS) 1 R320
162-50289001-E CABLE ASS'Y 280mm AWG26 WHT (RoHS) 1
162-80098201-E WIRE 90mm grey 28AWG (RoHS) 1 to SW301,
175-9f40hr2-E COUPLER 40PIN PITCH=2.54mm HR2*40 (RoHS) P301,
190-16tl074cn-E I.C TL074CN ST (RoHS) QUAD OP-AMP 1 U301,
197-631n4148-E DIODE 500mW 75V 1N4148 Panjit (RoHS) 1 D303
110-16103j26-E RESISTOR 10K 1/6W ±5% CF 26mm (RoHS) 8 R301,R303,R304,R308,R309,R314,R340,
R344,
110-16183j26-E RESISTOR 18K 1/6W ±5% CF 26mm (RoHS) 1 R302,
110-16223j26-E RESISTOR 22K 1/6W ±5% CF 26mm (RoHS) 2 R310,R312,
110-16273j26-E RESISTOR 27K 1/6W ±5% CF 26mm (RoHS) 1 R341,
110-16333j26-E RESISTOR 33K 1/6W ±5% CF 26mm (RoHS) 1 R305,
110-16472j26-E RESISTOR 4.7K 1/6W ±5% CF 26mm (RoHS) 2 R342,R343,
110-16474j26-E RESISTOR 470K 1/6W ±5% CF 26mm (RoHS) 1 R307,
110-16751j26-E RESISTOR 750Ω1/6W ±5% CF 26mm (RoHS) 2 R311,R313,
110-16755j26-E RESISTOR 7.5M 1/6W ±5% CF 26mm (RoHS) 1 R306,
130-3f104z503-E DISC CAPACITOR 0.1U 50V +80/-20% (RoHS) 2 C305,C306,
132-103j503-E MYLAR CAPACITOR 0.01uF 50V ±5% (RoHS) 2 C302,C303,
135-3226m50-E ELECTROYTIC CAP.22U 50V ±20% (RoHS) 2 C301,C340,
135-3476m25-E ELECTROYTIC CAP.47U 25V ±20% (RoHS) 1 C304,
192-027c1815gr-E TRANSISTOR 2SC1815GR TOSHIBA (RoHS) NPN 2 Q301,302
197-631n4148-E DIODE 500mW 75V 1N4148 Panjit (RoHS) 2 D301,D302,
MISCELLANEOUS
123-14j70d-E Ferrite Core U-16.3*8.2*13 (J70)+CASE (RoHS) 1
130-3f472md00-E DISC CAPACITOR 4700P 400V ± 20% (RoHS) 1 C001
150-E8604107-E TRANSFORMER EI-86 60Hz 120V TT0869906580 1
152-u602015-E POWER CORD JOINT HETEROPOLARITY SVT FT-2 6FT (RoHS) 1
154-u25006t0-E FUSE 2.5A 250V 20mm (RoHS) 1
155-520020-E FUSE HOLDER R3-11 (RoHS) 1
156-h200040-E THERMAL SHRINKABLE SLEEVING 20ψ*40mm (RoHS) 1
156-h200050-E THERMAL SHRINKABLE SLEEVING 20Φ50mm (RoHS) 1
162-10151001-E WIRE UL1617 150mm 22AWG BROWN 6:6 (RoHS) 1
166-a045a4bf-E HORN WIRE 450mm RED=205# 0.5T BLK=110#0.5T UL1015 18AWG 1
176-wjcE1-E WIRE CONNECTOR PIN CE-1 (RoHS) 1
180-prf1003s-E POWER SWITCH ROCK RF-1003-BB2-OHA (RoHS) 1
302-AL-05090-1LCE REAR BOARD 300*200*2.5T CSC80 120V USE (RoHS) 1
306-ABS-00177-0BAE REAR HOUSING 198*298*102mm (RoHS) 1
311-ABS-00028-0BAE PLASTIC KNOB 46077-W SOFT MATERIAL P.V.C. (RoHS) LEVEL 1
320-RUB-00033-0BAE RUBBER GASKET 25*21*4t GLUE ON BACK (RoHS) 4
14
CS80 (CS480 Subwoofer)

Part Number Description Qty Reference Designator
MISCELLANEOUS
323-AL-00141-0LAE HEAT SINK 117.5*71.5*25 (RoHS) 1
333-EVA-00783-0BAE GASKET W 198*12*2.0T (RoHS) 2
333-EVA-00807-0BAE GASKET L 274*12*2.0T (RoHS) 2
333-EVA-00826-0BAE GASKET W 198*12*1.0T (RoHS) 2
333-EVA-00835-0BAE GASKET L 274*12*1.0T (RoHS) 2
335-NYL-05015-0BAE WIRE CLIP SB4F-2 BLACK (RoHS) 2
337-CU-00101-0LAE COPPER FILM 65L*50W (RoHS) 1
350-EM04012D024-E 4*12WOOD SCREW ELECTRICAL BLACK (RoHS) 4
351-AM03008A079-E M3*8 MACHINE SCREW ELECTRICAL BLACK (RoHS) 7
351-HM04016A218-E M4*16 MACHINE SCREW ELECTRICAL BLACK (RoHS) 4
352-AM03008D040-E 3*8 B TYPE PING SCREW ELECTRICAL BLACK (RoHS) 8
352-AM03010D065-E 3*10 P TYPE PING SCREW ELECTRICAL BLACK (RoHS) 1
354-GM04002-E M4 NUT GASKET ELECTRICAL BLACK (RoHS) 4
362-FE-00013-0LAE PCB SUPPORT L TYPE t=1.6mm S.P.C.C 89*9*1.6T (RoHS) 2
15
CS80 (CS480 Subwoofer)

16
CS80 (CS480 Subwoofer)

17
CS80 (CS480 Subwoofer)

18
CS80 (CS480 Subwoofer)

19
CS80 (CS480 Subwoofer)
This manual suits for next models
1
Table of contents
Other JBL Subwoofer manuals