JBL SUB333 User manual

SUB333
60W Subwoofer
(Part of the ESC333 system)
JBL Consumer Products Inc.
250 Crossways Park Drive
Woodbury, N.Y. 11797
1-800-336-4JBL in the USA
A Harman International Company
Rev A 2/00
SERVICE MANUAL

2
Dolby Pro-LogicÒSurround Processor/Amplifier/Subwoofer SUB333
TABLE OF CONTENTS
ESC333 SPECIFICATIONS...........................................2
IMPORTANT NOTE .......................................................4
FEATURES.....................................................................4
ESC333 SPEAKER, SOURCE & REMOTE
SENSOR CONNECTIONS.............................................5
ABOUT DOLBY DIGITAL ..............................................5
REMOTE AND FRONT-PANEL CONTROLS
AND INDICATORS.........................................................6
SUB333 BLOCK DIAGRAM...........................................9
SUB333 UNIT EXPLODED VIEW ...............................10
SUB333 MECHANICAL PARTS LIST .........................11
SUB333 ELECTRICAL PARTS LIST .........................12
ESC333 PACKING EXPLODED VIEW .......................20
SUB333 MAIN PCB .....................................................21
SUB333 POWER PCB.................................................22
SUB333 DC PCB .........................................................23
SUB333 JACK & CONTROL PCB's............................24
SUB333 DECODER PCB (Top View) .........................25
SUB333 DECODER PCB (Bottom View)....................26
SUB333 LIMITER PCB ................................................27
INTEGRATED CIRCUIT DIAGRAMS ..........................28
SUB333 WIRING DIAGRAM .......................................34
SUB333 LIMITER SCHEMATIC ..................................35
SUB333 AC3 SCHEMATIC .........................................36
SUB333 MAIN SCHEMATIC .......................................37
ESC333 SPECIFICATIONS
LINE VOLTAGE Voltage Hi/Lo Line
US 120vac/60Hz Yes 120VAC 108-132VAC
EU 230vac/50-60Hz Yes 230VAC 207-264VAC
Parameter Spec. Unit Conditions Notes
Sat. Amplifiers 30w x 5 ch. section
Type (Class AB, D, other) AB — ESC350 Sink required
Load Impedance (speaker) 6 Ohms Nominal Z-curve required
Rated Output Power 30 Watts ALL CH.driven Marketing Spec.
THD@ Rated Power 0.08 % 22k filter 30w (BW 120Hz-15kHz)
THD @ 1 Watt 0.1 % 22k filter
Max. Output Power 35 Watts 2 ch. Stereo Mode Max @1%THD
DC Offset 2 mV-DC @ Speaker Outputs
Damping factor >200 DF —
Input Sensitivity (L,C,R,LS,RS)
Input Frequency 1k Hz Nominal Freq. 1 input driven
Line Input: Video/AUX 265 mVrms To Rated Power/ Vol @ Max 1 input driven
Signal to Noise (L,C,R,LS,RS)
SNR-A-Weighted 100 dBA relative to 30w power/ 1k ohm term. A-Weighting filter
SNR-unweighted 75 dBr relative to 30w power/ 1k ohm term. 22k filter
SNR rel. 1W-unweighted 65 dBr relative to 1W Output/ 1k ohm term. 22k filter
Residual Noise Floor 1 mVrms Volume @max, using RMS reading
DMM/VOM (or A/P)
Filters/EQ (L,C,R,LS,RS)
HPF,Notch,HF boost Fixed dBr 0dBr = 1w @ 1kHz
Subwoofer Amp 60w x 1 ch. section
Type (Class AB, D, other) AB — —
Load Impedance (speaker) 4 Ohms Nominal
Rated Output Power 60 Watts ALL CH.driven
THD@ Rated Power 0.08 % 22k filter 60w (BW 30-120Hz)

Parameter Spec. Unit Conditions Notes
THD @ 1 Watt 0.1 % 22k filter
Max. Output Power 80 Watts 2 ch. Stereo Mode @ 50Hz @1%THD
DC Offset 2 mV-DC @ Speaker Outputs
Damping factor >200 DF —
Input Sensitivity
Input Frequency 50 Hz Nominal Freq. 1 input driven
Line Input: Video/AUX 265 mVrms To Rated Power/ Vol @ Max 1 input driven
Signal to Noise
SNR-A-Weighted 100 dBA relative to 60w power/ 1k ohm term. A-Weighting filter
SNR-unweighted 75 dBr relative to 60w power/ 1k ohm term. 22k filter
SNR rel. 1W-unweighted 65 dBr relative to 1W Output/ 1k ohm term. 22k filter
Residual Noise Floor 1 mVrms Volume @max, using RMS reading
DMM/VOM (or A/P)
Input Impedance
Line Input: Video/AUX 20k ohms Nominal
Optical
Coax
Filters/EQ 0dBr = 1w @ 50Hz
HPF, LPF Fixed dBr 0dBr = 1w @ 50Hz
Signal Sens. (ATO)
Auto-Turn-On (yes/no) yes
ATO Input Frequency 1k Hz
ATO Level 2 mV 2mV@50Hz into Line Input w/ 1 ch. driven
ATO Bandwidth 5k Hz ATO-LPF for noise immunity
ATO Turn-on time 5 ms Amp connected and AC on, then input
signal applied
Auto Mute/ Turn-OFF 20 min. T before muting, after signal is removed
Power on Delay time 3 sec. AC Power Applied
Transients/Pops
Signal-Present Transient 5 mV-peak @ Speaker Outputs
Turn-on Transient 50 mV-peak @ Speaker Outputs AC cycled from
OFF to ON or ON to OFF
Efficiency
Stand-by Input Power 15 Watts @ nom. line voltage
Max Power Consumption 425 Watts @ nom. line voltage @ rated power
Efficiency 50 % Nominal... At rated output
Protection
Short Circuit Protection yes Direct short at output
Thermal Protection yes @1/8 max unclipped Power
DC Offset Protection yes DC present at Speaker Out leads
Line Fuse Rating 5 Amps Type-T or Slo Blo
3
Dolby Pro-LogicÒSurround Processor/Amplifier/Subwoofer SUB333

4
Dolby Pro-LogicÒSurround Processor/Amplifier/Subwoofer SUB333
IMPORTANT NOTE
Automatic On/Off and Automatic
Digital-Input Selection
The ESC333 offers two unique user-convenience features:
Automatic Turn-On/Shut-Down and Automatic Digital-Input
Selection.
The Automatic Turn-On feature will turn the ESC333 on as
soon as a source connected to its digital inputs (such as
DVD, CD player with digital output, or any other device
featuring a coaxial or optical digital output) is switched on, or
as soon as the unit connected to its last-used analog input
starts outputting sound.
When using digital inputs, the Automatic Turn-On can be
activated by turning on either one of the connected digital
sources such as a DVD player or a CD player with digital
output. When using analog inputs (TV or AUX), Automatic
Turn-On is available only for the device that was last
listened to before the ESC333 shut down. In order to listen
to the other device, the ESC333 input needs to be manually
selected by using the Input button on the product and on the
remote, which, in turn, disables the Automatic Digital-Input
Selector until the ESC333 is shut down.
The Automatic Turn-Off shuts the unit down five minutes
after all sources connected to its digital inputs are powered
down and the device connected to its selected analog input
stops playing.
The Automatic Digital-Input Selector automatically selects
the source connected to its digital inputs when that source is
powered on. Upon power down of this digital unit, if no other
source is on, the ESC333 will switch itself off after five
minutes.
If the analog source that was selected prior to the digital
source turning on is still playing, the ESC333 will switch
back to that other source. Once a digital source is powered
on and selected as an input, turning on a device connected
to the other digital input will not switch the input until the
selected digital device is first powered off. These two
features can only be used if the customer does not manually
turn the ESC333 on or off, and does not manually select an
input source. Once either of these selections is made
manually, the automatic features are disabled as follows:
1. If the ESC333 is turned off manually, it will not turn back
on automatically until five minutes after the source
connected to the ESC333 is shut down. During these five
minutes, it can be turned on either from the front panel or via
the remote control.
2. Once an input source is selected manually, the Automatic
Source-Selection feature will remain disabled until the
ESC333 shuts down.
3. Once any one of the two devices connected to the
ESC333 digital inputs is powered on and its input is selected
by the ESC333, the device connected to the other digital
input of the ESC333 cannot be automatically selected until
the already-selected digital device is powered down.
FEATURES
• Complete, self-powered Dolby* Digital home-cinema
sound system with five satellite speakers, subwoofer,
remote control, and all amplification built in. (Just Add TV!)
• Dolby Digital (AC-3* 5.1 channel), Dolby Pro Logic,*
including Phantom and 3-Stereo, and Stereo listening
modes.
• Automatic Turn-On and Turn-Off.
• Automatic Source Switching for the digital inputs.
• Two digital (one optical and one coaxial) inputs and two
analog inputs.
• 2-Way video-shielded micro-satellites with titanium
laminate tweeters and common voicing for all five channels,
and an 8-inch, long-throw, floor-firing subwoofer.
• Late Night compression for nighttime listening without
unexpected and objectionably loud passages.
• All amplification and controls are mounted in the
sub-woofer, eliminating the need for a separate control unit.
• Remote controllable via outboard remote eye that can be
mounted with the center channel or separately, so that the
subwoofer can be hidden away.
• Wall-mount brackets and floor stands available separately
for the satellites.
• Credit-card-type, full-function remote control.
• JBL “error free” speaker cables simplify connection and
eliminate possibility of out-of-phase wiring.
• Center foot for horizontal placement of the center channel.
• Rotatable JBL logos to allow for vertical or horizontal
placement of the satellites.

5
Dolby Pro-LogicÒSurround Processor/Amplifier/Subwoofer SUB333
Left Front
TV
OPTICAL
Right Left
Center
Right Front
Remote Sensor
COAXIAL
TV
AUX
COAXIAL
OPTICAL
Right Surround
Left Surround
FRONT
SPEAKERS
SURROUND
SPEAKERS
RIGHT
CENTER
LEFT
RIGHT
LEFT
AC POWER
ON / STANDBY
OFF
REMOTE SENSOR
INPUT
RIGHT
AUX
(Additional Audio Source)
Audio Output
Right Left
ANALOG
INPUTS
DIGITAL
INPUTS
Digital Source A
DVD or CD
Digital Output
Digital Source B
DVD or CD
Digital Output
LEFT
ESC333 SPEAKER, SOURCE & REMOTE SENSOR CONNECTIONS
ABOUT DOLBY DIGITAL
The ESC333 features Dolby Digital (also unofficially known
as AC-3) multichannel signal processing, a system
developed by Dolby Laboratories.
Dolby Digital, unlike “matrixed”systems (such as Dolby Pro
Logic) that derive and decode multichannel sound from two
channels of sound, is capable of delivering information for
one subwoofer and five full-range channels as discrete and
individual channels in digital AC-3 data format from sources
such as a DVD player. The result is clear and accurate
digital sound to each speaker, along with availability of
stereo-surround effects (Dolby Pro Logic features mono
surrounds).
Dolby Digital is capable of delivering several different
formats of surround sound, the most robust one being the
5.1-channel mode, which provides separate signals for five
satellite speakers as well as for a subwoofer. The ESC333
features a “5.1-Ch”indicator that illuminates when a Dolby
Digital 5.1-channel encoded signal is present. Dolby Digital
can also provide other AC-3 digital multichannel signals, as
well as 2-channel signals, which can be decoded via Dolby
Pro Logic processing into multichannel surround sound. In
the latter case, both the Dolby Pro Logic and Dolby Digital
indicators will illuminate in the ESC333 display.

REMOTE AND FRONT-PANEL CONTROLS AND INDICATORS
1. Power
This button, located only on the remote control, allows the
user to manually turn on or off the ESC333. Please note that
the ESC333 features Automatic Turn-On/Off, and the power
switch is not normally used unless it is necessary to override
this automatic feature, or in case the analog input to be used
is not the last one that was used and so Automatic Turn-On
is not available for that input. Please read the details
regarding Automatic Turn-On/Off on page 3 of this manual,
and keep in mind that if the ESC333 is shut down using this
power button, its automatic turn-on feature will remain
disabled for five minutes after the source connected to the
ESC333 is also shut down. This is to prevent the ESC333
from repeatedly turning itself back on against the user’s
wishes. The ESC333 can also be powered on by using the
Input button (4) on the front panel of the subwoofer or on the
remote control. Please note that if input selection is done by
pressing the Input button, the Automatic Digital Input
Selection of the ESC333 will be disabled until the ESC333
shuts down.
When the ESC333 is plugged into a working electrical outlet
and its master switch on the back panel is set to
On/Standby, the Standby (32) indicator will illuminate. The
ON (31) indicator will light as soon as the ESC333 is turned
on either automatically or via the pressing of the Power or
Input buttons.
2. Mute
From either the front panel or the remote control, press
(Mute) to lower the volume completely. The mute symbol
indicator (33) will illuminate. When you press either of the
mute buttons again, the volume will return to its previous
setting.
Note: The mute function can also be turned off by pressing
either of the volume buttons on the front panel or the remote
control.
6
Dolby Pro-LogicÒSurround Processor/Amplifier/Subwoofer SUB333
LATE NIGHT
POWER
MUTE
SURROUND
MODE
INPUT ADJUSTMENT
TREBLE
BASS
VOLUME
1
2
3
7
9
4
5
6
8
10
13
12
11
0dB
DELAY
TEST
LEVEL
DOLBY
DIGITAL
Input Surround Mode Volume Mute
Late Night LVL3-St Phantom Surround
PCM SUB ProLogic Digital 5.1 Ch
AUX DLYTV
DIG. COAX DIG. OPT
ON
STANDBY
LSLFCRFRS
23 19 22
20
2421 26
25 30
17 28 29
546227
18
16
15
14
31
32
33

3. Late Night
This feature is available for Dolby Digital only. It
compresses the inherently dynamic digital sound so that the
quiet and loud passages are not quite as different in sound
levels as they ordinarily are. This feature allows the user to
watch movies and listen to dialogue at toned-down levels so
as not to disturb others by the loud sound effects that may
be present. The Late Night indicator (26) illuminates when
this feature is active.
4. Input
This control is available on both the front panel and the
remote control. It allows manual selection when the user
repeatedly presses and releases the button for any of the
ESC333’s four inputs. The ESC333 features an Automatic
Digital Input Selection feature that automatically switches
the ESC333 to the source connected to one of its two digital
inputs as soon as that device is powered on. Please read
the section on page 3 to thoroughly familiarize yourself with
the conveniences and conditions of using the Automatic
Digital Input Selection feature. The Input switch is also used
when the source connected to the ESC333’s analog input is
not the analog source that was listened to the last time the
ESC333 was on (and hence the Automatic Turn-On feature
is not available). The Input switch also turns on the ESC333
when pressed (see item 1 earlier in this section). Whenever
a specific input is selected either manually or automatically,
its indicator (14, 15, 16 or 17) on the ESC333’s front panel
will be illuminated.
5. Surround Mode
Pressing and releasing this button allows the selection of
different listening modes. Surround (18), Phantom (19) and
3-Stereo (20) are available listening options for Dolby Digital
and Dolby Pro Logic. Stereo (21) bypasses the surround
processing and outputs sound through the right and
left-front speakers only. In Surround mode, all five satellites
and the sub-woofer will play. In Phantom mode, all speakers
except the center channel will play. In 3-Stereo, all speakers
except for the two surround speakers will be active.
6. Volume
Press (+) on the remote control or the front panel to raise
the system’s volume. Press (-) on the remote control or the
front panel to lower the system’s volume. The volume
setting is indicated on the status-bar indicator (27).
7.0dB
Press this button to reset the Center, Surround, Balance,
Treble and Bass controls to their default positions.
8. Test
Press this button to activate the Test Tone mode.
9. Delay
The relative timing of sounds coming from the center and/or
surround speakers compared to the front-left and front-right
speakers can be adjusted. The first press of this button
allows adjustment of the center channel, all the way from
the default setting of 0 ms (milliseconds), which means no
delay (all status bars off), to a maximum of 5 ms (5 status
bars on). The indicators C (28) and DLY (30) will be on. The
second press of the Delay button allows adjustments of the
surround speakers; indicators LS (28) and RS (28) and DLY
(30) will be on. The delay can be adjusted from zero (all
status bars off) to 15 ms (all status bars on) in 5.1 Channel
Dolby Digital and from 15 ms (all status bars off) to 30 ms
(all status bars on) in Dolby Pro Logic (there is an inherent
and fixed 15 ms of delay added in the “matrixed”Dolby Pro
Logic to recreate the proper surround effect). The center
and surround delay adjustments can be done from either
Dolby Digital or Dolby Pro Logic “matrixed”modes. There
are no separate delay adjustments for the individual modes
of operation. During adjustments, the audio mutes
momentarily every time the Adjustment +/–button (11) is
pressed. Please note that the status-bar indicator (27) will
not display unless Adjustment +/–buttons are pressed.
Also, while the status-bar indicator (27) is on, channel
indicators (28) and DLY (30) will not be displayed. And, if
adjustments are done in a mode where a certain channel is
not available, the adjustment step for that channel is
skipped. For example, in Phantom mode, the
center-channel delay cannot be adjusted since Phantom
does not have a center channel. In Stereo, neither the
center nor the surround delay can be adjusted since Stereo
does not feature surround speakers or a center speaker. A
third press of the Delay button will exit the ESC333 from its
delay-adjustment mode.
10. Level
The relative level of sounds coming from each of the
ESC333’s speakers can be adjusted while listening to
program material on the ESC333. Repeated pressing and
releasing of the Level button allows access to each channel.
The display will indicate LVL (29), and the channel
indicators (28) LF (Left Front), C (Center), RF (Right Front),
LS (Left Surround), RS (Right Surround) and SUB
(sub-woofer) will illuminate to indicate the active speaker.
The level for the selected channel can then be changed
using the Adjustment +/–buttons (11). Levels set in one
mode will stay valid for all other modes and are not
independent. Please note that the status-bar indicator (27)
7
Dolby Pro-LogicÒSurround Processor/Amplifier/Subwoofer SUB333

will not display unless Adjustment +/–buttons are pressed.
And, while the status-bar indicator 27) is on, channel
indicators (28) and LVL (29) will not be displayed. Also, if
adjustments are done in a mode where a certain channel is
not available, the adjustment step for that channel is
skipped. For example, in Phantom mode the center-channel
level cannot be adjusted since Phantom does not have a
center channel. In stereo, neither the center nor the
surround levels can be adjusted since Stereo does not
feature surround speakers or a center speaker. A seventh
press of the Level button will exit the ESC333 from its
level-adjustment mode.
11. Adjustment
These buttons are used in conjunction with Test (8), Delay
(9), and Level (10) to increase or decrease a setting.
12. Bass
Press (+) to increase the level of low-frequency information.
Press (–) to decrease the level of low-frequency
information.
13. Treble
Press (+) to increase the level of high-frequency
information. Press (–) to decrease the level of
high-frequency information.
14–17. Input
One of these four indicators will illuminate, depending on
which input is selected.
18–21. Surround
One of these will illuminate, depending on which surround
mode is chosen.
22. Dolby Digital
Indicates the presence of a Dolby Digital-encoded AC-3
digital signal.
23. 5.1-Ch
Works in conjunction with the Dolby Digital indicator (22).
This indicator illuminates when the Dolby Digital signal
contains 6 discrete channels of information (one subwoofer
and five satellite channels).
24. Dolby Pro Logic
Illuminates when Dolby Pro Logic decoding of a 2-channel
signal is taking place. This indicator may be on by itself
(when analog inputs are used), in conjunction with Dolby
Digital (when using a digital input where the AC-3 format
signal contains two channels and needs to be decoded into
multichannel) or together with PCM (when using a digital
input where 2-channel PCM-format data is being decoded
into multi-channel).
25. PCM
Illuminates when the signal supplied through the selected
digital input is in PCM format.
26. Late Night
Illuminates when the Late Night compression is selected.
27. Status-Bar Indicator
These LEDS show the relative setting of volume, bass,
treble, speaker level and speaker delay.
28. Speaker Indicator
Identifies the speaker that’s being adjusted. LS is Left
Surround, LF is Left Front, C is Center, RF is Right Front,
RS is Right Surround, and SUB is Subwoofer.
29. Level
Illuminates when the ESC333 is in speaker-level adjustment
mode.
30. Delay
Illuminates when the ESC333 is in speaker-delay
adjustment mode.
31. On
Indicates that the ESC333 is fully powered up.
32. Standby
Indicates that the ESC333 is plugged into an active wall
outlet and the master switch on the back panel is in
On/Standby position, but the unit is not powered on.
33. Mute
Illuminates when the mute function is activated (the
ESC333 will be on but will not produce any sound).
8
Dolby Pro-LogicÒSurround Processor/Amplifier/Subwoofer SUB333

11
Dolby Pro-LogicÒSurround Processor/Amplifier/Subwoofer SUB333
SUB333 MECHANICAL PARTS LIST
Ref.# Part # Description Qty. Ref.# Part # Description Qty.
1 EVM0033-001 WOOD BOX 1
2 BPR0020-000 PORT EDGE 1
3 BPR0042-BA0 PORT 1
4 BPF5056-BA1 CONTROL PANEL 1
5 BNP0073-001 PVC PLATE 1
6 BPL0013-001 LOGO PLATE 1
7 BPK5031-000 CONTROL BUTTON ASSEMBLY 1
8 APE0283-001 CONTROL PCB ASSEMBLY 1
9 IVE0041-001 WOOFER GASKET 1
10 FTW6080-312 4 OHM 8' WOOFER 1
11 BRF0015-001 RUBBER PAD 4
12 BPB0012-001 BOTTOM CABINET 1
13 BRF0014-001 RUBBER PAD 4
14 IVE0042-001 BOX SPONGE 1
15 BPH0054-000 LED HOLDER 1
18 BPA0021-001 REAR COVER 1
19 APE0284-001 JACK PCB ASSEMBLY 1
20 GSE0255-001 JACK PLATE 1
21 MSV0001-004 SWITCH ROCKER 1
22 DBU0002-001 BUSHING 1
23 47455-D52 6.5 ft. AC LINE CORD 1
24 GAL0055-003 HEAT SINK 1
25 TTL1201-001 120V POWER TRANSFORMER 1
TTL2301-001 230V POWER TRANSFORMER 1
26 APE0280-001 MAIN PCB ASSEMBLY 1
27 GSE0253-001 PCB BRACKET RIGHT 1
28 GSE0254-001 PCB BRACKET LEFT 1
29 GSE0093-001 HEAT SINK BRACKET 1
30 APE0214-003 DECODER PCB ASSEMBLY 1
31 GTN0063-001 SHIELD PLATE UP 1
32 GTN0064-001 SHIELD PLATE DOWN 1
33 APE0281-001 POWER PCB ASSEMBLY 1
34 APE0282-011 DC PCB ASSEMBLY 1
35 GSE0256-001 PCB BRACKET RIGHT 1
36 GSE0257-001 PCB BRACKET LEFT 1
37 BRB0003-001 RUBBER BUSHING 1
38 BRB0004-001 RUBBER BUSHING 1
39 BRB0005-001 RUBBER BUSHING 1
N1 HNI1482 NUT @ 14x3.5 mm 4
S1 H101001-108 SCREW T3.0x1.27P 3
-2RHxL8.0 mm
S2 H016504-316 SCREW W6#-20xl16.0 mm 4
S3 H016701-316 SCREW W8#-18xL16.0 mm 8
S4 H101001-310 SCREW T3.0x1.27PxL10.0 mm 3
S5 HO60501-320 SCREW M4.0x0.7PxL20.0 mm 10
S6 H060301-314 SCREW M3.0x0.5PxL14.0 mm 2
S7 H060404-321 SCREW M3.5x0.6PxL21.0 mm 4
S8 H120301-306 SCREW M3.0x0.5PxL6.0 mm 4
S9 H041001-314 SCREW T3.0x1.27P-2RHxL14.0 2
S10 H1110022-306 SCREW T3.0x1.27P-2RHxL6.0

Fuses
F901, F902 (DC PCB) KSA2800-001 FUSE 8A 250V 2
F903, F904 (DC PCB) KSA2160-003 FUSE 1.6A 250V 5x20 mm 2
W/UL. CSA. T MARKING
F905 (DC PCB) KSA2100-002 FUSE 1A 250V 5x20 mm 1
W/UL. CSA. T MARKING
F906, F907 KSA2400-104 FUSE 4A 250V SLOW 5ST BEL 2
(PWR PCB) 5x20mm CSA/UR/VDE/SE
APE0214-003 DECODER PCB ASSY
Connectors
CN601A CCN7879-031 CONNECTOR J.S.T. 2.0 mm PH 1
B11B-PH-K TOP SIZE
CN602A CCN2032-L15 CONNECTOR TUC-P15X-B1 1
PITCH=2.0 mm SIDE
CN603A CCN2032-L07 CONNECTOR TUC-P7X-B1 1
PITCH=2.0 mm SIDE
Capacitors
C635, C636, C637, PRE3953-101 COND ELECT 100uF 25V 20% 85’C 4
C638
C639, C640 PRM3737-682 COND MYLAR 0.0068uF 100V 5% 2
C641, C642, C643, PRE3951-470 COND ELECT 47uF 10V 20% 85’C 4
C644
C645 PRE3951-100 COND ELECT 10uF 10V 20% 85’C 1
C646, C648, C670 PMA3955-109 COND ELECT 1uF 50V 20% 3
P=2.5 mm AI (MINI)
C647, C657, C658, PCW3965-104 CHIP CAP 0.1uF 50V +80-20% 18
C659, C660, C661, TYPE Y5V
C662, C663, C664,
C665, C666, C667,
C668, C671, C839,
C840, C841, C843
C649, C651, C652, PMA3951-479 COND ELECT 4.7uF 10V 20% 6
C653, C654, C790 P=2.5 mm AI (MINI)
C672, C673 PCW1035-300 CHIP CAP 30pF 50V 5% 2
TYPE NPO
C674 PRM3737-473 COND MYLAR 0.047uF 100V 5% 1
C675 PRM3737-103 COND MYLAR 0.01uF 100V 5% 1
C676 PEP2636-104 COND MPEM 0.1uF 63V 5% 1
MINI SIZE (AI)
C677, C691, C738, PRE3953-101 COND ELECT 100uF 25V 20% 85’C 7
C789, C795, C809
C811
C678, C679, C682, PCW5635-682 CHIP CAP 0.0068uF 50V 5% 12
C683, C688, C692,
C693, C696, C697,
C700, C701, C803
C680, C684, C689, PEP2636-474 COND MPEM 0.47uF 63V 5% 6
C694, C698, C702 MINI SIZE (AI)
C681, C685, C690, PCW1035-561 CHIP CAP 560pF 50V 5% 6
C695, C699, C703 TYPE NPO
C686, C728, C734, PMA3951-470 COND ELECT 47uF 10V 20% 16
C748, C752, C753, P=2.5 mm AI (MINI)
C755, C757, C766,
C767, C783, C784,
C786, C787, C788,
C829
C704, C705, C706, PMA3951-101 COND ELECT 100uF 10V 20% 10
C713, C715, C716, P=2.5 mm AI (MINI)
C717, C726, C765,
C785,
C720, C724, C736, PMA3953-101 COND ELECT 100uF 25V 20% 13
C750, C754, C798, P=2.5 mm AI H=7mm
C799, C800, C801,
C810, C812, C815,
C816
C723, C729, C730, PCW1035-331 CHIP CAP 330pF 50V 5% 6
C741, C744, C756 TYPE NPO
C758 PCW1035-220 CHIP CAP 22pF 50V 5% 1
TYPE NPO
C759, C832, C880, PRD3545-104 COND DISC 0.1uF 50V 10% Y5P 4
C882
C760 PMA3952-220 COND ELECT 22uF 16V 20% 1
P=2.5 mm AI (MINI)
C761 PRM3737-152 COND MYLAR 0.0015uF 100V 5% 1
C762 PRM3737-153 COND MYLAR 0.015uF 100V 5% 1
C764 PRE3951-101 COND ELECT 100uF 10V 20% 85’C 1
C768, C778, C779 PMA3952-101 COND ELECT 100uF 16V 20% 3
P=2.5 mm AI (MNI)
C769, C773, C777, PCW1035-470 CHIP CAP 47pF 50V 5% 12
C780, C781, C782, TYPE NPO
C834, C835, C836,
C837, C838, C842
C770, C776 PEP2636-824 COND MPEM 0.82uF 63V 5% 2
MINI SIZE (AI)
C771, C775 PRM3737-562 COND MYLAR 0.0056uF 100V 5% 2
C772, C774 PRM3737-472 COND MYLAR 0.0047uF 100V 5% 2
C813, C814 PMA3955-339 COND ELECT 3.3uF 50V 20% 2
P=2.5 mm AI (MINI)
C830, C831 PVE3951-102 COND ELECT 1000uF 10V 20% HI 2
C833 PCW5635-223 CHIP CAP 0.022uF 50V 5% 1
TYPE X7R
C881 PCW1035-101 CHIP CAP 100pF 50V 5% 1
TYPE NP
C883 PMA3955-479 COND ELECT 4.7uF 50V 20% 1
P=2.5 mm AI (MINI)
C887 PCW3955-104 CHIP CAP 0.1uF 50V 20% 1
TYPE Y5V
C888 PRD1335-390 COND DISC 39pF 50V 5% NPO 1
Diodes
D601 RCD4148-001 DIODE SW LL4148 TELEFUNKEN 1
SMT TYPE
D602 RAD4001-001 RECTIFIER 1N4001 1A 35VRMS 1
ZD601, ZD602 RAZ0859-073 DIODE ZENR 6.9-7.2V 0.5W 2
HITACHI HZ7B-2
Integrated Circuits
IC601 RCI3861-001 IC 100 PIN ZR38601 ZORAN 1
AC3 DECODER
IC605,IC606,IC608, RCI0720-001 IC 8 PIN TL072 SMT TYPE 11
IC609,IC610, DUAL OP-AMP
IC611,IC612,
IC613, IC621,
IC622, IC623
IC607 RCI1117-001 IC 3 PIN REG1117 3.3V 1
12
Dolby Pro-LogicÒSurround Processor/Amplifier/Subwoofer SUB333
SUB333 ELECTRICAL PARTS LIST
Ref.# Part # Description Qty. Ref.# Part # Description Qty.

IC614-IC619 RCI4051-001 IC 16 PIN TC4051BFN CHIP 6
8 CH MULTIPLEXER
IC620 RCI6244-001 IC 42 PIN M62446FP ELECTRONIC 1
VOLUME CONTROL
IC624 RCI7404-001 IC 14 PIN TC74HC04AFN TOSHIBA 1
HEX INVERTER
IC625 RCI4052-001 IC 16 PIN TC4052BFN CHIP 1
4 CH MULTIPLEXER
IC626 RCI4227-001 IC 44 PIN CS4227 1
6 CH VOL CRYSTAL
IC627 RHI0256-001 IC 28 PIN EPROM IC 256K 120ns 1
Resistors
R601, R670, R674, QCF0152-000 CHIP RES. 0 OHM JUMP WIRE 6
R675, R676, R891 SMT TYPE
R673 QCF0152-473 CHIP RES. 47K OHM 1/10W 5% 1
SMT TYPE
R677, R736, R741, QCF0152-472 CHIP RES. 4.7K OHM 1/10W 5% 12
R746, R750, R756, SMT TYPE
R764, R809, R812,
R823, R888, R889
R678, R838, R882, QCF0152-223 CHIP RES. 22K OHM 1/10W 5% 5
R883, R884
R679, R683, R696, QCF0152-222 CHIP RES. 2.2K OHM 1/10W 5% 6
R698, R700, R707 SMT TYPE
R680, R695 QCF0152-122 CHIP RES. 1.2K OHM 1/10W 5% 2
SMT TYPE
R681, R684, R738, QCF0152-152 CHIP RES 1.5K OHM 1/10W 5% 8
R743, R748, R753, SMT TYPE
R758, R768
R682, R697, R699, QCF0152-162 CHIP RES. 1.6K OHM 1/10W 5% 5
R701, R848 SMT TYPE
R685, R686, R716, QCF0152-103 CHIP RES. 10K OHM 1/10W 5% 17
R717, R718, R719, SMT TYPE
R761, R788, R797,
R799, R813, R892,
R893, R894, R895,
R896, R897
R689 QAF0450-109 RESISTOR 1.0 OHM 1/4W 5% CF 1
R690 QAF0650-472 RESISTOR 4.7K OHM 1/6W 5% CF 1
R691, R709, R720, QCF0152-101 CHIP RES. 100 OHM 1/10W5% 29
R721, R722, R723, SMT TYPE
R785, R791, R798,
R802, R808, R821,
R825, R826, R835,
R849, R850, R851,
R852, R853, R855,
R856, R876, R877,
R878, R879, R880,
R881, R898
R692 QAF0650-102 RESISTOR 1K OHM 1/6W 5% CF 1
R693 QAF0650-681 RESISTOR 680 OHM 1/6W 5% CF 1
R694, R714, R715, QCF0152-390 CHIP RES. 39 OHM 1/10W 5% 5
R725, R726 SMT TYPE
R702 QCF0152-622 CHIP RES. 6.2K OHM 1/10W 5% 1
SMT TYPE
R703, R822, R827, QCF0152-822 CHIP RES. 8.2K OHM 1/10W 5% 12
R830, R833, R834, SMT TYPE
R836, R837, R842,
R843, R844, R845
R706, R740, R745, QCF0152-102 CHIP RES. 1K OHM 1/10W 5% 13
R751, R754, R762, SMT TYPE
R846, R854, R864,
R865, R868, R869,
R875
R708 QCF0152-202 CHIP RES. 2K OHM 1/10W 5% 1
SMT TYPE
R710, R711 QCF0152-203 CHIP RES. 20K OHM 1/10W 5% 2
SMT TYPE
R712, R713 QCF0152-682 CHIP RES. 6.8K OHM 1/10W 5% 2
SMT TYPE
R730 QCF0152-209 CHIP RES. 2 OHM 1/10W 5% 1
SMT TYPE
R735, R744, R749, QCF0152-512 CHIP RES. 5.1K OHM 1/10W 5% 6
R755, R759, R770 SMT TYPE
R737, R742, R747, QCF0152-562 CHIP RES. 5.6K OHM 1/10W 5% 6
R752, R757, R766 SMT TYPE
R801, R803, R804, QCF0152-224 CHIP RES. 220K OHM 1/10W 5% 6
R805, R806, R816 SMT TYPE
R807 QCF0152-301 CHIP RES. 300 OHM 1/10W 5% 1
SMT TYPE
R810 QCF0152-183 CHIP RES. 18K OHM 1/10W 5% 1
SMT TYPE
R815 QCF0152-433 CHIP RES. 43K OHM 1/10W 5% 1
0805 SMT TYPE
R817, R818, R819, QCF0152-362 CHIP RES. 3.6K OHM 1/10W 5% 5
R828, R829 SMT TYPE
R820 QCF0152-331 CHIP RES. 330 OHM 1/10W 5% 1
SMT TYPE
R847 QCF0152-392 CHIP RES. 3.9K OHM 1/10W 5% 1
SMT TYP
R862, R863, R866, QCF0152-272 CHIP RES. 2.7K OHM 1/10W 5% 7
R867, R873, R874, SMT TYPE
R887
R885, R886 QHM1050-151 RESISTOR 150OHM 1W 5% MF 2
Transistors
Q607 RCN1623-001 XISTR NPN SMT TYPE (2SC945) 1
HFE:200-400
Q608 RAP0733-001 XISTR PNP 2SA733Q,P NEC AI 1
Q609 RAN2001-001 XISTR NPN 2SC2001L NEC 1
Wires
CN604 4999A-519 CON/WRE AY 3 COND 150 mm 1
SHIELD WIRE
CN605 4999A-520 CON/WRE AY 3 COND 250 mm 1
SHIELD WIRE
CN606 4999A-522 CON/WRE AY 2 COND 260 mm 1
SHIELD WIRE
Miscellaneous
L606, L609 SAF0835-001 BEAD RH035083ST-Y7 3.5X8.3X0.76 2
L607, L610 SHC8121-101 CHOKE 100uh 2
L611 SRC0210-001 CHOKE TOKIN SBT-0210 1
COPPER SIDE XTP9777-023 TAPE HIGH TEMP TAPE NICHIBAN
IC601, IC626
L6, C884, L602, L603, SCF0805-600 CHIP BEAD 2012A601Y102B
L612, L613, L614, TEAM YOUNG
L615, L616D, L617,
L619-L649
13
Dolby Pro-LogicÒSurround Processor/Amplifier/Subwoofer SUB333
SUB333 ELECTRICAL PARTS LIST Cont...
Ref.# Part # Description Qty. Ref.# Part # Description Qty.

L604, L605 SAC7414-100 CHOKE 10uH AI 2
XL602 JQC6071-320 CRYSTAL 32.0000 MHz L=5.0 mm 1
APE0280-001 MAIN PCB ASSY
Connectors
CN201 CCN7879-030 CONNECTOR J.S.T. 2.0 mm PH 1
B10B-PH-K TOP SIZE
CN202 CCN7879-028 CONNECTOR J.S.T. 2.0 mm PH 1
B 8B-PH-K TOP SIZE
CN203 CCN7879-027 CONNECTOR J.S.T. 2.0 mm PH 1
B 7B-PH-K TOP SIZE
CN204 CCN7879-025 CONNECTOR J.S.T. 2.0 mm PH 1
B 5B-PH-K TOP SIZE
CN602 CCN2032-015 CONNECTOR TUC-P15P-B1 1
PITCH=2.0 mm TOP
CN603 CCN2032-007 CONNECTOR TUC-P7P-B1 1
PITCH=2.0 mm TOP
CN604 CCN7879-023 CONNECTOR J.S.T. 2.0 mm PH 1
B 3B-PH-K TOP SIZE
CN605 CCN1500-023 CONNECTOR B 3B-XH-A 3 PIN 1
POST BASE TOP P:2.5
CN606 CCN1500-018 CONNECTOR B 2B-XH-A 2 PIN 1
POST BASE TOP P:2.5
Capacitors
C101, C105 PRD4965-103 COND DISC 0.01uF 50V +80-20% 2
Z5V II D=6
C102, C106, C110, PRD3965-104 COND DISC 0.1uF 50V +80-20% 18
C111, C206, Y5V/Z5V
C211, C325,
C326, C336,
C337, C338,
C339, C403,
C404, C605,
C606, C637,
C638
C104, C108, C201, PRE3955-109 COND ELECT 1uF 50V 20% 85’C 8
C323, C324, C414,
C503, C504
C109, C305, C306, PRE3953-470 COND ELECT 47uF 25V 20% 85’C 10
C311, C312, C315,
C316, C319, C320,
C327
C202, C203 PRD1335-180 COND DISC 18pF 50V 5% 2
NP0 D=5
C204 PRE3955-478 COND ELECT 0.47uF 50V 20% 85’C 1
C205 PVE3951-222 COND ELECT 2200uF 10V 20% 1
C207, C210 PRE3952-470 COND ELECT 47uF 16V 20% 85’C 2
C208, C511 PRD4965-223 COND DISC 0.022uF 50V +80-20% 2
Z5V II D=7
C209 PRE3952-100 COND ELECT 10uF 16V 20% 85’C 1
C301, C302, C307, PRD3545-101 COND DISC 100pF 50V 10% Y5P 4
C308
C303, C304, C309, PRD1335-470 COND DISC 47pF 50V 5% NP0 9
C310, C328,
C331, C363,
C364, C719
C313, C314, C321, PRE3953-221 COND ELECT 220uF 25V 20% 85’C 10
C322, C356, C357,
C418, C419, C705,
C706
C317, C318 PRD1335-220 COND DISC 22pF 50V 5% 2
NP0 D=5
C332, C333, C401, PRM3737-822 COND MYLAR 0.0082uF 100V 5% 5
C601, C602
C334, C335, C402, PRD3545-221 COND DISC 220pF 50V 10% 5
C603, C604 Y5P II D=5C330
C340, C341, C342, PRM3737-273 COND MYLAR 0.027uF 100V 5% 10
C343, C405, C406,
C607, C608, C609,
C610
C344, C345, C346, PRM3737-472 COND MYLAR 0.0047uF 100V 5% 20
C347, C352, C353,
C354, C355, C407,
C408, C411, C412,
C611, C612, C613,
C614, C619, C620,
C621, C622
C348, C349, C410, PRM3737-222 COND MYLAR 0.0022uF 100V 5% 8
C413, C501, C502,
C617, C618
C350, C351, C409, PRD3545-201 COND DISC 200pF 50V 10% Y5P 5
C615, C616
C415, C507, C508 PRD1395-509 COND DISC 5pF 50V +-0.5 pF 3
NP0 D=5
C416, C505, C506 PRE3952-330 COND ELECT 33uF 16V 20% 85’C 3
C417, C509, C510, PRM3737-104 COND MYLAR 0.1uF 100V 5% 5
C723, C724
C512 PRE3951-100 COND ELECT 10uF 10V 20% 85’C 2
C513, C514, C515, PRE3955-101 COND ELECT 100uF 50V 20% 4
C516
C517 PRE3953-101 COND ELECT 100uF 25V 20% 85’C 1
C523, C524 PRE3954-470 COND ELECT 47uF 35V 20% 85’C 2
C525 PRE3952-471 COND ELECT 470uF 16V 20% 85’C 1
C526 PRE3955-229 COND ELECT 2.2uF 50V 20% 85’C 1
C527 PRE3953-100 COND ELECT 10uF 25V 20% 85’C 1
C720, C721 PRM3737-183 COND MYLAR 0.018uF 100V 5% 2
C722 PRM3737-303 COND MYLAR 0.03uF 100V 5% 1
C725 PRM3737-683 COND MYLAR 0.068uF 100V 5% 1
C726 PRM3737-123 COND MYLAR 0.012uF 100V 5% 1
Diodes
D201, D202, D203, RAD4148-001 DIODE SW 1N4148 22
D204, D206, D207,
D303, D304, D305,
D306, D307, D308,
D401, D402, D501,
D502, D503, D504,
D505, D506, D507,
D508
D205 RAD4001-001 RECTIFIER 1N4001 1A 35VRMS 1
ZD201 RAZ0859-070 DIODE ZENR 5.6-5.9V 0.5W 1
HITACHI HZ6B-2
ZD301 RAZ0859-059 DIODE ZENR 2.3-2.5V .5W 1
ZD501,ZD502 RAZ0859-093 DIODE ZENR 22.3-23.3V 0.5W 2
HITACHI HZ22-3
14
Dolby Pro-LogicÒSurround Processor/Amplifier/Subwoofer SUB333
SUB333 ELECTRICAL PARTS LIST Cont...
Ref.# Part # Description Qty. Ref.# Part # Description Qty.

Integrated Circuits
IC201 RCI8747-041 IC 44 PIN TC9819 1
8 BIT MICROCONTROLLER
IC202, IC203, IC204 RHI4094-001 IC 16 PIN TC4094BP TOSHIBA 3
8 BIT SHIFT REGISTER
IC301 RHI4052-001 IC 16 PIN TC4052BP DIP 1
4 CH MULTIPLEXER
IC302, IC303, IC304, RHI0740-001 IC 14 PIN TL074CN QUAD OP-AMP 7
IC401, IC601,
IC602, IC702
IC501 RHI0407-250 IC 20 PIN STK407-250 POWER IC 1
IC701 RHI5218-002 IC 8 PIN M5218AL MITSUBISHI 1
OP AMP L TYPE
Resistors
R101, R103, R106, QAF0650-103 RESISTOR 10K OHM 1/6W 5% CF 40
R108, R113, R118,
R119, R120, R214,
R229, R230, R237,
R251, R252, R253,
R254, R255, R256,
R257, R258, R259,
R261, R263, R265,
R267, R269, R271,
R273, R275, R277,
R279, R283, R285,
R287, R289, R290,
R291, R292, R311,
R312
R102, R107, R321, QAF0650-105 RESISTOR 1.0M OHM 1/6W 5% CF 6
R322, R378, R379
R104, R109, R110, QAF0650-151 RESISTOR 150 OHM 1/6W 5% CF 5
R211, R327
R105, R112, R225, QAF0650-473 RESISTOR 47K OHM 1/6W 5% CF 9
R238, R239, R526,
R528, R531, R533
R116, R201, R202, QAF0650-472 RESISTOR 4.7K OHM 1/6W 5% CF 38
R203, R204, R205,
R206, R207, R208,
R209, R212, R213,
R215, R216, R217,
R218, R219, R220,
R221, R223, R224,
R226, R227, R228,
R231, R236, R323,
R324, R365, R366,
R414, R532, R534,
R544, R627, R628,
R725, R737
R117, R288, R309, QAF0650-102 RESISTOR 1K OHM 1/6W 5% CF 13
R310, R313, R314,
R331, R373, R374,
R416, R501, R502,
R729
R210, R315, R316, QAF0650-332 RESISTOR 3.3K OHM 1/6W 5% CF 4
R701
R232, R317, R318, QAF0650-101 RESISTOR 100 OHM 1/6W 5% CF 7
R369, R370, R735,
R736
R240, R355, R356, QAF0650-104 RESISTOR 100K OHM 1/6W 5% CF 20
R357, R358, R380,
R410, R411, R417,
R420, R427, R503,
R504, R521, R522,
R527, R619, R620,
R621, R622
R247, R381, R382 QAF0650-471 RESISTOR 470 OHM 1/6W 5% CF 3
R248, R249, R260, QAF0650-152 RESISTOR 1.5K OHM 1/6W 5% CF 30
R262, R264, R266,
R268, R270, R272,
R274, R276, R278,
R280, R284, R286
R293, R294, R295,
R296, R297, R298,
R299, R422, R425,
R509, R510, R517,
R518, R539, R540
R301, R302, R303, QAF0650-243 RESISTOR 24K OHM 1/6W 5% CF 14
R304, R305, R306,
R307, R308, R363,
R364, R377, R413,
R625, R626
R329, R334 QAF0650-224 RESISTOR 220K OHM 1/6W 5% CF 2
R332, R525, R732 QAF0650-223 RESISTOR 22K OHM 1/6W 5% CF 3
R341, R342, R402, QAF0650-273 RESISTOR 27K OHM 1/6W 5% CF 5
R603, R604
R343, R344, R403, QAF0650-202 RESISTOR 2K OHM 1/6W 5% CF 5
R605, R606
R347, R348, R361, QAF0650-913 RESISTOR 91K OHM 1/6W 5% CF 10
R362, R406, R412,
R609, R610, R623,
R624
R351, R352, R353, QAF0650-203 RESISTOR 20K OHM 1/6W 5% CF 10
R354, R407, R408,
R613, R614, R615,
R616
R359, R360, R409, QAF0650-682 RESISTOR 6.8K OHM 1/6W 5% CF 7
R617, R618, R703,
R705
R367, R368, R415, QAF0650-752 RESISTOR 7.5K OHM 1/6W 5% CF 5
R629, R630
R375, R376 QAF0650-681 RESISTOR 680 OHM 1/6W 5% CF 2
R383, R384 QAF0650-100 RESISTOR 10 OHM 1/6W 5% CF 2
R421, R511, R512 QAF0650-563 RESISTOR 56K OHM 1/6W 5% CF 3
R423, R513, R514 QAF0250-479 RESISTOR 4.7 OHM 1/2W 5% CF 3
R424, R515, R516 QVE3050-228 RESISTOR 0.22 OHM 3W 5% 3
CEMENT FIXED RADIAL
R426, R519, R520, QAF0650-393 RESISTOR 39K OHM 1/6W 5% CF 4
R523
R428, R429 QAF0450-101 RESISTOR 100 OHM 1/4W 5% CF 2
R536, R537 QAF0450-330 RESISTOR 33 OHM 1/4W 5% CF 2
R543, R734 QAF0650-222 RESISTOR 2.2K OHM 1/6W 5% CF 2
R704, R706 QAF0650-153 RESISTOR 15K OHM 1/6W 5% CF 2
R726 QAF0650-362 RESISTOR 3.6K OHM 1/6W 5% CF 1
R727 QAF0650-683 RESISTOR 68K OHM 1/6W 5% CF 1
R731 QAF0650-204 RESISTOR 200K OHM 1/6W 5% CF 1
R733 QAF0650-363 RESISTOR 36K OHM 1/6W 5% CF 1
R738 QAF0650-109 RESISTOR 1 OHM 1/6W 5% CF 1
Transistors
Q101, Q102, Q103, RAN0945-001 XISTR NPN 2SC945P NEC 36
Q104, Q251, Q252,
Q253, Q254, Q255,
Q256, Q257, Q258,
Q259, Q260, Q261,
Q263, Q264, Q267,
Q268, Q269, Q272,
Q273, Q274, Q275,
15
Dolby Pro-LogicÒSurround Processor/Amplifier/Subwoofer SUB333
SUB333 ELECTRICAL PARTS LIST Cont...
Ref.# Part # Description Qty. Ref.# Part # Description Qty.

Q276, Q277, Q278,
Q279, Q301, Q302,
Q402, Q503, Q504,
Q505, Q508, Q513
Q509 Q511 RAN2001-001 XISTR NPN 2SC2001L NEC 2
Q401, Q501, Q502 RAN2878-001 XISTR NPN 2SC2878-A (TE2,M) 3
Q506, Q510 RAP0733-001 XISTR PNP 2SA733Q,P NEC AI 2
Q265, Q266, Q270, RAP0952-001 XISTR PNP 2SA952 NEC 5
Q271, Q512
Miscellaneous
MAIN PCB-1 GSE0093-001 HEAT SINK BRACKET 1
HT946
MAIN PCB-1 GSE0253-001 BRACKET PCB BRACKET-R SECC 1
MAIN PCB-1 GSE0254-001 BRACKET PCB BRACKET-L SECC 1
PCB BKT TO H120301-306 SCREW T3.0x0.5pxL6.0 mm 7
MAIN PCB-7 PAN HEAD BLACK
CR201 JQC6070-419 CRYSTAL 4.194304 MHz HC-49/U 1
RL501, RL502 MRL2212-002 RELAY MI-SH-212LM 12V DC 2
44 mA GOOD SKY
L402, L501, L502 SHR6619-001 RF COIL 1uH MDEC T40818-08 3
P3 TO AC3 20565-060BB WIRE 22 GA 60 mm BLACK 4-4 1
CPB JW20 UL 1007 TOP COATED
P1-P1 20565-130BB WIRE 22 GA 130 mm BLACK 4-4 1
UL 1007 TOP COATED
P2 TO P2 20565-150BB WIRE 22 GA 150 mm BLACK 4-4 1
UL 1007 TOP COATED
P4 TO P4 20565-260BB WIRE 22 GA 260 mm BLACK 4-4 1
UL 1007 TOP COATED
RB904 4999A-512 CON/WRE AY 5 COND 400 mm #18 1
RB502 4999A-515 CON/WRE AY 7 COND 300 mm #18 1
RB301 4999A-517 CON/WRE AY 6 COND 280 mm 1
SHIELD WIRE
RB205 4999A-518 CON/WRE AY 3 COND 400 mm 1
SHIELD WIRE
RB506 4999A-521 CON/WRE AY 5 COND 200 mm 1
SHIELD WIRE
RB302 4999A-526 CON/WRE AY 5 COND 350 mm 1
SHIELD WIRE
RB601 4999A-542 CON/WRE AY 11 COND 70mm P=2.01
UL1007 #26 WHT/BLK
RB504 500351801B0 COND WIRE 5 COND 180 mm 1
BLACK
RB906 500393001B0 COND WIRE 9 COND 300 mm 1
BLACK 26 AWG PITCH=2.5 mm
APE0281-001 POWER AMP PCB ASSY
Connectors
CN501 CCN3962-006 CONNECTOR 6 PIN CL3962WVO 1
CN502 CCN3962-007 CONNECTOR 7 PIN CL3962WVO 1
PITCH=3.96 mm
CN503 CCN3962-004 CONNECTOR 4 PIN CL3962WVO 1
PITCH=3.96 mm
CN504, CN506 CCN1500-016 CONNECTOR B 5B-XH-A 5 PIN 2
POST BASE TOP P:2.5
CN505 CCN3962-002 CONNECTOR 2 PIN CL3962WVO 1
P=3 96mm POST BASE TOP
CN903 CCN3962-003 CONNECTOR 3 PIN CL3962WVO 1
Capacitors
C623, C624 PRM3737-222 COND MYLAR 0.0022uF 100V 5% 2
C625, C626 PRE3955-109 COND ELECT 1uF 50V 20% 85’C 2
C627, C628, C708, PRE3952-330 COND ELECT 33uF 16V 20% 85’C 4
C712
C629, C630, C709 PRD1395-509 COND DISC 5pF 50V +-0.5 pF 3
NP0 D=5
C631, C632, C717 PRM3737-104 COND MYLAR 0.1uF 100V 5% 3
C633, C634, C635, PRE3955-101 COND ELECT 100uF 50V 20% 85’C 6
C636, C710, C716 VENTED TYPE
C639 PRE3953-470 COND ELECT 47uF 25V 20% 85’C 1
C640 PRE3953-470 COND ELECT 47uF 25V 20% 85’C 1
C707 PRE3952-100 COND ELECT 10uF 16V 20% 85’C 1
C711 PRD3545-101 COND DISC 100pF 50V 10% Y5P 1
C713, C714 PRD3545-471 COND DISC 470pF 50V 10% 2
Y5P II D=5
C718 PRM3737-472 COND MYLAR 0.0047uF 100V 5% 1
C935, C936, C937, PRD4965-223 COND DISC 0.022 uF 50V 4
C938 +80-20% Z5V II D=7
C939, C940 PVE3956-222 COND ELECT 2200uF 63V 20% 2
Diodes
D601, D602, D603, RAD4148-001 DIODE SW 1N4148 7
D604, D701, D702,
D703
D915, D916, D917, RHD5404-001 RECTIFIER 1N5404 4
D918
ZD601, ZD602 RAZ0859-093 DIODE ZENR 22.3-23.3V 0.5W 2
HITACHI HZ22-3
Integrated Circuits
IC603 RHI0407-050 IC 15 PIN STK407-050 POWER IC 1
IC703 RHI4038-001 IC 15 PIN STK4038II POWER IC 1
Resistors
R631, R632, R722 QAF0650-102 RESISTOR 1K OHM 1/6W 5% CF 3
R633, R634, R651, QAF0650-104 RESISTOR 100K OHM 1/6W 5% CF 6
R652, R708, R721
R635, R636, R637, QAF0650-103 RESISTOR 10K OHM 1/6W 5% CF 8
R638, R655,
R709, R710,
R724
R639, R640, R647, QAF0650-152 RESISTOR 1.5K OHM 1/6W 5% CF 9
R648, R653,
R654, R711,
R715, R719
R641, R642, R712 QAF0650-563 RESISTOR 56K OHM 1/6W 5% CF 3
R643, R644, R717 QAF0250-479 RESISTOR 4.7 OHM 1/2W 5% CF 3
R645, R646, R718 QVE3050-228 RESISTOR 0.22 OHM 3W 5% 3
CEMENT FIXED RADIAL
16
Dolby Pro-LogicÒSurround Processor/Amplifier/Subwoofer SUB333
SUB333 ELECTRICAL PARTS LIST Cont...
Ref.# Part # Description Qty. Ref.# Part # Description Qty.

R649, R650, R720 QAF0650-393 RESISTOR 39K OHM 1/6W 5% CF 3
R713 QAF0650-223 RESISTOR 22K OHM 1/6W 5% CF 1
R714, R716 QAF0450-101 RESISTOR 100 OHM 1/4W 5% CF 2
R723 QAF0450-330 RESISTOR 33 OHM 1/4W 5% CF 1
Transistors
Q601, Q602, Q701 RAN2878-001 XISTR NPN 2SC2878-A (TE2,M) 3
Q603, Q604, Q702 RAN0945-001 XISTR NPN 2SC945P NEC 3
Q605 RAP0952-001 XISTR PNP 2SA952 NEC 1
Q606, Q703 RAN2001-001 XISTR NPN 2SC2001L NEC 2
Miscellaneous
F906, F907 CFC2557-001 FUSE CLIP5D5X20FUSE 4
L601, L602, L701 SHR6619-001 RF COIL 1uH MDEC T40818-08 3
P2 TO P2 20565-081BB WIRE 22 GA 80mm BROWN 4-4 1
UL 1007 TOP COATED
P1 TO P1 20565-200BB WIRE 22GA 200 mm BLACK 4-4 1
UL 1007 TOP COATED 1
POWER PCB-1 GSE0256-001 BRACKET PCB BRACKET (R) SECC 1
POWER PCB-1 GSE0257-001 BRACKET PCB BRACKET (L) SECC 1
PCB BKT TO H120301-306 SCREW T3.0x0.5pxL6.0 mm 3
POWER PCB-3 PAN HEAD BLACK
PCB BKT TO H120302-306 SCREW M3.0x0.5PxL6.0 mm 1
POWER PCB-1 BLACK W/WASHER
RB905 4999A-513 CON/WRE AY 4 COND 250 mm #18 1
RB100 4999A-632 CON/WRE AY 4 COND 250 mm 1
GY-GY P:2.5/2 28AWG UL1533
RB102 50024AE1BMM COND WIRE 3 COND 150 mm 1
BROWN
RL701 MRL2212-002 RELAY MI-SH-212LM 12V DC 1
44 mA GOOD SKY
APE0282-021 CONNECTOR PCB ASSY
DC PCB-1 GSE0256-001 BRACKET PCB BRACKET (R)
SECC ESC333
DC PCB-1 GSE0257-001 BRACKET PCB BRACKET (L)
SECC ESC333
PCB BKT TO H120301-306 SCREW T3.0x0.5pxL6.0 mm 4
DC PCB-4 PAN HEAD BLACK
RB101 500331501B6 COND WIRE 3 COND 150 mm 1
APE0282-011 DC PCB ASSY
Connectors
CN901 CCN3962-006 CONNECTOR 6 PIN CL3962WVO 1
CN902 CCN3962-002 CONNECTOR 2 PIN CL3962WVO 1
96mm POST BASE TOP
CN904 CCN3962-005 CONNECTOR 5 PIN CL3962WVO 1
PITCH=3.96 mm
CN905 CCN3962-004 CONNECTOR 4 PIN CL3962WVO 1
PITCH=3.96 mm
CN906 CCN1500-033 CONNECTOR B 9B-XH-A 9 PIN 1
POST BASE TOP P:2.5
Capacitors
C901, C902, C903, PRD4965-223 COND DISC 0.022 uF 50V 13
C904, C909, +80-20% Z5V II D=7
C910, C911,
C912, C915,
C916, C917,
C918, C934
C906, C908 PVE3955-472 COND ELECT 4700uF 50V 20% 2
C913, C914 PVE3954-222 COND ELECT 2200uF 35V 20% 85’C 2
C919 PVE3953-222 COND ELECT 2200uF 25V 20% 1
C920, C922, C924, PRD3965-104 COND DISC 0.1uF 50V +80-20% 8
C925, C927, Y5V/Z5V
C929, C931,
C933
C921 PRE3953-220 COND ELECT 22uF 25V 20% 85’C 1
C923, C926 PRE3953-221 COND ELECT 220uF 25V 20% 85 2
C928 PRE3954-101 COND ELECT 100uF 35V 20% 85’C 1
C930, C932 PRE3952-101 COND ELECT 100uF 16V 20% 85’C 2
VENTED TYPE
Diodes
D901, D902, D903, RHD0600-400 RECTIFIER 6A 400V P600G 4
D904
D905, D906, D907, RAD4002-001 RECTIFIER 1N4002 9
D908, D909,
D910, D911,
D912, D913
ZD901 RAZ0859-067 DIODE ZENR 4.7-4.9V 0.5W 1
HITACHI HZ5B-2
Integrated Circuits
IC901 RHI7815-001 IC 3 PIN REGULATOR 15V 1A 1
IC902 RHI7915-001 IC 3 PIN 7915 -15V REGULATOR 1
IC903 RHI7906-001 IC 3 PIN 7906 -6V REGULATOR 1
IC904 RHI7806-001 IC 3 PIN MC7806ACT (5V2) 1
+6V REGULATOR
Resistors
R907 QAF0250-470 RESISTOR 47 OHM 1/2W 5% CF 1
R910 QAF0650-332 RESISTOR 3.3K OHM 1/6W 5% CF 1
R911 QAF0650-472 RESISTOR 4.7K OHM 1/6W 5% CF 1
R912 QAF0650-473 RESISTOR 47K OHM 1/6W 5% CF 1
R913 QAF0650-103 RESISTOR 10K OHM 1/6W 5% CF 1
R914 QAF0450-222 RESISTOR 2.2K OHM 1/4W 5% CF 1
Transistors
Q906 RAP0733-001 XISTR PNP 2SA733Q,P NEC AI 1
Miscellaneous
F901-F905 CFC2557-001 FUSE CLIP5D5X20FUSE 1
17
Dolby Pro-LogicÒSurround Processor/Amplifier/Subwoofer SUB333
SUB333 ELECTRICAL PARTS LIST Cont...
Ref.# Part # Description Qty. Ref.# Part # Description Qty.

APE0282-021 CONNECTOR PCB ASSY
Connectors
CN205, CN305 CCN1500-023 CONNECTOR B 3B-XH-A 3 PIN 2
POST BASE TOP P:2.5
CN301, CN303 CCN1500-024 CONNECTOR B 6B-XH-A 6 PIN 2
POST BASE TOP P:2.5
CN302, CN304 CCN1500-016 CONNECTOR B 5B-XH-A 5 PIN 2
POST BASE TOP P:2.5
Miscellaneous
TO TIN FOIL CSL6521-002 SOLDER LUG OD7.0xID3.5xT0.3 mm 1
NICKEL
PA TO SOLDER LUG 20565-160BB WIRE 22 GA 160 mm BLACK 4-4 1
UL 1007 TOP COATED
AFA0048-004 CONTROL PANEL ASSY
LEDs
LD203, LD226-LD233, KEG0402-001 LED 2x4 mm BRIGHT GREEN 17
LD236-LD243
LD204, LD205, LD206 KEG0525-001 LED 2.5x5mm BRIGHT GREEN 22
LD207, LD210,
LD211, LD212,
LD214-LD225,
LD234, LD235,
LD244
LD201, LD202, KER0052-003 LED 2x5 mm RED 523 4
LD208, LD209 ID/LD-A HIGH LIGHT
Resistors
R243, R244 QAF0650-391 RESISTOR 390 OHM 1/6W 5% CF 2
R242 QAF0650-471 RESISTOR 470 OHM 1/6W 5% CF 1
R245 QAF0650-122 RESISTOR 1.2K OHM 1/6W 5% CF 1
Wires
RB201 4999A-523 CON/WRE AY 10 COND 320 mm 1
PITCH=2.0 mm
RB202 4999A-524 CON/WRE AY 8 COND 300 mm 1
PITCH=2.0 mm
RB203 4999A-511 CON/WRE AY 7 COND 300 mm 1
PITCH=2.0 mm
RB204 4999A-525 CON/WRE AY 5 COND 300 mm 1
PITCH=2.0 mm
Miscellaneous
RB201, RB202 XTP9777-023 TAPE HIGH TEMP TAPE
(COPPER SIDE) NICHIBAN 241
TA201, TA202, TA203, MAT2029-001 AI TACT SW 5.0 mm 160 gf 5
TA204, TA205 ALPS SKHVBE3520
BNP0073-001 PVC PLATE 1
BPF5056-BA1 CNTL PANEL (DP6P 1083) 1
BPK5031-000 CNTL KNOB 1
CTRL PCB TO H101001-108 SCREW T3.0x1.27p-2RHXL8.mm 3
CTRL PANEL-3 PAN HEAD NICKEL
CONTROL PANEL IVE0085-001 EVA SPONGE L100 x W30 x 2
WIRE DRESSING-2 T2.0mm BACK W/ADHESIVE
CONTROL PANEL
BPH0054-000 LED HOLDER ESC333 1
APE0362-001 AMP PLATE ASSEMBLY
Miscellaneous
JACK ASSY-1 BPA0021-001 REAR COVER HI-PS ESC350 (JBL) 1
JACK ASSY-1 BRB0004-001 RUBBER BUS NR-3 1
0.0616 JACK ASSY-1
JACK ASSY-1 KSA1600-001 FUSE 6A 125V SLOW 5x20 mm UL
JACK ASSY-2 BRB0003-001 RUBBER BUS NR-3 1
GSE0255-001 JACK PLATE SECC 120V
ESC333 (JBL)
BRB0005-001 RUBBER BUS NR-3
0.0305 SW RACKER
BRF0007-001 RUBBER BLACK 1
0.0800 AC CORD
DBU0002-001 BUSHING AC LINE BUSHING 1
PIN GOOD 4RF-5
DFH1229-001 FUSE HOLDR FUSE HOLDER 1
FH-B02 10A; DIA 5.2x20
0.5576 COND SAFETY-2
LIMITED PCB TO DSS0002-006 SPACER OD5.0xID3.1xH5.0 mm 2
REAR COVER &
CON PCB-2
POWER SW TO H060301-314 SCREW M3.0x0.5pxL14.0mm 2
JACK PLT-2 PAN HEAD BLACK
AC3 JACK TO JACK H101001-310 SCREW T3.0x1.27p-2RHxL10mm 9
PLT-2, JACK PCB PAN HEAD BLACK
TO JACK PLT-4 RCA JACK TO JACK PLT-1
CONNECTOR PCB H101002-114 SCREW T3.0x1.27p-2RHxL14mm 2
TO REAR COVER-2 W/WASHER NICKEL
LIMITED PCB TO
REAR COVER &
CON PCB-2
MSV0001-004 SW ROCKER 5A AC 250V TV-5 1
CHILY CAT NO.3051
0.7515 POWER SW-1
PLS3559-104 COND SAFTY 0.1uF 250V 20% 1
X2 CAP LEAD:25mm
SLF0201-013 BEAD FERIT BRH 17.5x12.7x9.5 1
CHILISIN
2559-080022 LINE LINK 370 mm BLACK VDE 1
ESC300 (JBL)
47455-D52 LINE CORD SPT-2 1980mm 1
POLARIZ BLK-UL DOUBLE INSULA
FUSE TO AC SW
5823-092BB WIRE 22 GA 90 mm RED 4-4 1
UL1617 DOUBLE INSULA
BUSHING-1, RUBBER-2
18
Dolby Pro-LogicÒSurround Processor/Amplifier/Subwoofer SUB333
SUB333 ELECTRICAL PARTS LIST Cont...
Ref.# Part # Description Qty. Ref.# Part # Description Qty.

APE0284-001 JACK PCB ASSY
Capacitors
C358, C359, C360, PRD3545-470 COND DISC 47pF 50V 10% Y5P 4
C361
C362, C518, C519, PRD4965-223 COND DISC 0.022 uF 50V 6
C520, C521, C522 +80-20% Z5V II D=7
Jacks
JK201 CJM9380-028 JACK PHONE JYE TAI 3542-01-030 1
3.5 DIM
JK301 CJR6504-002 JACK RCA 4P RJ-1073-10-0300A 1
JYE TAI RED/WHITE
JK302 CTP0008-003 RCA JACK RJ-1081-05-0300A 1
1T GREEN
JK303 CJT0001-001 JACK TOSLINK JACK 1
2.8121 TO JACK PLATE
CSL6521-002 SOLDER LUG OD7.0xID3.5xT0.3 mm
NICKEL
JK501 CTM0005-001 TERMINAL JACK ASSY MOLEX 1
TYPE
Resistors
R372 QAF0650-472 RESISTOR 4.7K OHM 1/6W 5% CF1 1
L301 SAC7414-100 CHOKE 10uH AI 1
0.0260 GND TO SOLDER LUG
Wires
20565-081BB WIRE 22 GA 80mm BROWN 4-4
UL1007 TOP COATE
RB303 4999A-527 CON/WRE AY 6 COND 150 mm 1
SHIELD WIRE
RB304 4999A-528 CON/WRE AY 5 COND 150 mm 1
SHIELD WIRE
RB305 4999A-520 CON/WRE AY 3 COND 250 mm 1
SHIELD WIRE
RB501 4999A-516 CON/WRE AY 6 COND 300 mm #18 1
RB503 4999A-514 CON/WRE AY 4 COND 400 mm #18 1
APE0362-001 LIMITER PCB ASSY
Capacitors
C100 PRN3952-100 COND ELECT 10uF 16V 20% N.P. 1
C101 PRE3953-479 COND ELECT 4.7uF 25V 20% 85’C 1
C102, C104 PRE3953-101 COND ELECT 100uF 25V 20% 85’C 2
C103, C105 PRD3965-104 COND DISC 0.1uF 50V +80-20% 2
Y5V/Z5V
Connectors
CCN1500-015 CONNECTOR B48-XH-A 4 PIN POST BASE TOP 1
CCN1500-023 CONNECTOR B 3B-XH-A 3 PIN POST BASE TOP 2
Diodes
D100, D101 066X0070001 DIODE SW 1N914B 2
Integrated Circuit
IC100 RHI4558-001 IC 8 PIN JRC4558D JRC OP AMP 1
Resistors
R100, R103 QAF0650-223 RESISTOR 22K OHM 1/6W 5% CF 2
R101, R102 QAF0650-102 RESISTOR 1K OHM 1/6W 5% CF 2
R104, R105, R107,
R109, R110 QAF0650-103 RESISTOR 10K OHM 1/6W 5% CF 5
R106 QAF0650-105 RESISTOR 1.0M OHM 1/6W 5% CF 1
R108 QAF0650-474 RESISTOR 470K OHM 1/6W 5% CF 1
R111, R112 QAF0650-101 RESISTOR 100 OHM 1/6W 5% CF 2
R113 QAF0650-222 RESISTOR 2.2K OHM 1/6W 5% CF 1
Transistors
Q100, Q101 086X0113501 XISTR NPN 2N3904 MOTOROLA 2
Miscellaneous
JW100 AI20870-022 WIRE BARE 22 GA TINNED
19
Dolby Pro-LogicÒSurround Processor/Amplifier/Subwoofer SUB333
SUB333 ELECTRICAL PARTS LIST Cont...
Ref.# Part # Description Qty. Ref.# Part # Description Qty.