jcb 407 User manual

407, 409
QUICK REFERENCE GUIDE
This Quick Reference Guide DOES NOT replace the Operators
Manual. You MUST read ALL the disclaimers and safety and other
instructions in the Operators Manual before initially operating this
product. Accordingly, no legal claims can be entertained based on
the data, illustrations or descriptions in this Quick Reference Guide.
Access additional information
www.servicepro.jcb.com
Instrument Panel
Start Up Sequence
Static Dimensions
Tie Down Points
Cab and Switch Panel
A. Restraint angular range 8° to 11 °
B. Restraint angular range 40 ° to 50 °
C. Front tie down points
D. Rear tie down points
E. Tie down restraint
A. Steering wheel
B. Instrument panel
C. Multi-purpose steering column switch
D. Forward/reverse switch
E. Lift arm control lever
F. Right console switches
G. Creep speed control
H. Ignition switch
J. Hand throttle control
K. Park brake
L. Steering column adjustment
M. Accelerator pedal
N. Service brake pedal
P. Horn
Q. Front window blind
R. Cab interior light
S. Speakers
1. Battery/ Alternator no charge
2. Transmission Error/Fault
3. Transmission oil temperature
4. Park brake
5. Engine ECU fault/stop
6. Engine pre-heat
7. Engine fault
8. Engine oil pressure
9. Engine air filter
10. Water in fuel
11. Smooth ride system
12. Hydraulic error/fault
13. Transmission oil pressure
14. Foot brake
15. Fuel level
16. Engine coolant temperature
17. Rear fog light
18. Main beam
19. Trailer direction indicators
20. Direction indicators
21. Hazard warning
A. LCD Display
B. Fuel level gauge
C. Engine temperature gauge
Revision 1.0
12/2/2020

Service Points
Access Covers
Drive Controls Lifting Procedures
Lift Arm Controls
A. Forward/reverse switch
B. Tortoise speed button
C. Hare speed button
D. Differential lock button
E. Forward drive
F. Reverse drive
G. Neutral drive
Manual Controls
A. Single spool control configuration
B. Twin spool control configuration
F. Tortoise/hare speed range switches
G. First auxiliary spool control
H. Second auxiliary spool control (if installed)
J. Control lever
Lift Arm Control Lever
A. Raise
B. Lower
C. Float
D. Tilt shovel forward (dump)
E. Tilt shovel backward (crowd)
A. Battery isolator (position depends on specification)
B. Coolant expansion bottle
C. Engine oil filler point
D. Engine oil level dipstick
E. Diesel fuel filler point
F. Hydraulic tank filler point
G. Battery
H. Washer bottle
J. Hydraulic oil fluid level indicator
K. Air filter
L. Fuel water separator/filter
M. Engine oil filter
N. Fuel filter
Auxiliary Circuit Controls
A. Sling points
B. Instructional label
A. H beam lifting spreader
B. Center of Gravity
C. Machine lifting point
D. Lifting chain 5° Minimum angle
E. Lifting Chain 15° Maximum angle
F. Lifting chain 5°Minimum angle
G. Lifting Chain 15°Maximum angle
H. Centre of Gravity
A. H beam lifting spreader
J. 0° angle maximum (not shown)
K. 5° Maximum angle
L. Front of machine
M. Rear of machine
N. Perpendicular line –lifting point
P. Lifting chain
Engine Compartment Cover
A. Lock
Cab Heater Door
A. Access panel
B. Lock
Adding Attachments - Quickhitch
A. Pivot-shaft
B. Hook
C. Locking pin
D. Hole
A. Auxiliary lever
B. Auxiliary switch
1. Park machine on level ground.
2. Lower quickhitch and tilt forward.
3. Move machine forward until pivot-
shaft is below the hooks.
4. Lift quickhitch until pivot shaft engages
with hooks.
5. Tilt quickhitch backwards to align the
locking pins with hole in attachment.
6. Push and hold quickhitch isolator
switch until buzzer sounds.
Manual Servo