JCL Lighting Vesta A small User manual

Vesta C led
Vesta A small | VSTAS
Ø 6~12
Ghisamestieri the green way of light s.r.l. • Azienda certific ta ISO 9001:2008 • phone [phone] • fax. [phone] • [email protected] • www.ghisamestieri.it
Instruction manual
Operation and maintenance manual
1. Pre installatin checks
2. Mark fac-simile
Verify the product integrity and the compatibility of the
technical data in the mark placed on the product with the
plant.
If there aree incompatibilities do nothing and contact the
company.
Symbols key (if any)
Version
CE mark
Insulation class II
(not present in class I)
Waste disposal
Not attaching the light source
according to the photobiological
safety
Brand safety
Pic. 1
Available versions
Timeless
Regenerable luminaire with
replaceable LEDs and drivers
without tools.
Geometric features
Height 318 mm
Widht 456 mm
Lenght 456 mm
Weight 6 kg (wiring excluded)
Exposed area Lateral: 0,03 m² | Pianta: 0,10 m ²
Electrical features
PF > 0.90
Imax- Imin 700 mA - 200 mA
Installation features
Work environment Outdoor
Assembly position Horizontal
Maximum environment temperature 40°C
Mounting height < 15 m
Hygroscopic moisture 0 – 100 %
Degree of protection IP 66
collection: lightecture | up date: 2017.02
WARNING |
Read this manual carefully and store it in a safe
place for further use.
Set up must be carried out by specialized
technicians only.
Installation
The lantern is suitable for installation on wire system, final diameter
of the cable Ø6-12 (Pictures 1).
JCL LIGHTING - 70 rue Louis Armand - ZI Les Milles - BP 144 - 13794 Aix-en-Provence Cedex 3 (France) -
Tél : [phone] - Fax : [phone] - [email protected] - www.jcllighting.com

a.
f.
6
b.
c. d. e.
3. Set up guide
WARNING
Before completing the device make sure
you have switched the system’s power o.
1. 2.
6 mm
25 mm
25 mm
6 mm
Make the electrical connection
CLASS II
CLASS I
Tighten the cable
clamp
Strip back the cables as shown in picture 1. Connect the switching station, as a function of the insulation class. Tighten the
block cable red, as shown in Figure 2.
Tools
Place the lighting fi ture on the cable wire. Adjust the
orientation by unscrewing the nut from 3/4 gas positio-
ned under the attack. Maximum rotation of the lantern
/--30 °. Tighten the nut. Secure the safety cord around a
tensioned cable and lock it with spring hook.
Insert the locking clamp in the wire system accessory.
Lock the lighting fi ture through the tightening of the
M6 screw, coupling torque 5Nm. Tighten the nuts for
device locking.
If you need to back tilt.
Insert the cable into PG16 in the
wire system accessory, and
introduce it inside the luminaire.
Open the lighting fi ture as shown in
the pictures, by acting on the opening
system.
Slide the cable inside the lantern throu-
gh the fairlead, until it reaches the line
disconnector.
Make the electrical connection
Power cord
bracket
JCL LIGHTING - 70 rue Louis Armand - ZI Les Milles - BP 144 - 13794 Aix-en-Provence Cedex 3 (France) -
Tél : [phone] - Fax : [phone] - [email protected] - www.jcllighting.com

Vesta A small | VSTAS | Timeless
g.
h.
h1. h2.
12
ab
Ghisamestieri the green way of light s.r.l. • Azienda certific ta ISO 9001:2008 • phone [phone] • fax. [phone] • [email protected] • www.ghisamestieri.it
Instruction manual | Operation and maintenance manual
Close the luminaire sure to have triggered the closure.
SET UP THE PG16 WITH A TORQUE BETWEEN 2.5 AND 3 Nm.
Installation
Power cord
bracket
Removal of components
Driver door bracket removal disconnect
the quick connect bracket. Power LED
modules and (b) and the power cable to
the driver (a).
Turn the Red knob and remove the bra-
cket.
LED module extraction using the Red
knobs in Figure 2, loosen the bracket
door modules. Remove the bracket and
pull out the modules.
LED module LED module placement place
the bracket in the slot. When in position,
tighten the plate with red knobs are visible
in Picture 2.
Inserting driver door driver door bracket
place the bracket in position and secure it by
tightening the knob nall Allen red in Figure
1. Connect all the connectors power LED
modules, and (b) and (a) driver’s power.
JCL LIGHTING - 70 rue Louis Armand - ZI Les Milles - BP 144 - 13794 Aix-en-Provence Cedex 3 (France) -
Tél : [phone] - Fax : [phone] - [email protected] - www.jcllighting.com

4.1 Maintenance
4.2 Waste disposal pursuant to European
Directive 2012/19/UE
The  xture should be positioned so that there is not a long
observation at a distance less than 4 m.
Do not use the lantern if it seems damaged and/or broken.
Restore the original use/reuse conditions.
For spare parts, contact the manufacturer.
Warning! Before carrying out any extraordinary
maintenance operation, make sure you have switched
the system’s power off .
Maintenance operations shall only concern external
cleaning , the lamp replacement and the control of the
fastening of the device on the support.
The lamp replacement must be carried out by the
manufacturer, by its care service or by specialized
technicians only.
At the end of the useful life of the electrical products and/
or components, do not dispose the product with urban
waste.
Take it to the special municipal separate collection points.
4.3 Compliant packaging pusuant to
CE Directive 94/62
- 100%  brocartaceo material
- 100% recyclable and biodegradable
- Recyclable material content of the product shall be
- at least 90 % by weight.
4. Warnings
JCL Lighting
70 rue Louis Armand
ZI Les Milles - BP 144
13794 Aix-En-Provence Cedex 3
(France)
Tél : [phone]
Fax : [phone]
[email protected]
www.jcllighting.com
JCL LIGHTING - 70 rue Louis Armand - ZI Les Milles - BP 144 - 13794 Aix-en-Provence Cedex 3 (France) -
Tél : [phone] - Fax : [phone] - [email protected] - www.jcllighting.com