JENIX DSC-Q01 User manual

DSC-Q01 (1axis display)
user’s manual
DONG SAHN JENIX CO., LTD.

Contents
Description of DSC-Q01 counter
1. Front side
2. Rear side
3. Connection
4. Key description
Basic operation
1. Input (preset)
2. Display zero
3. ABS/INC conversion
4. ABS number designation
Function
1. Changing resolution
(1) 5/1000
(2) 1/1000
(3) 1/100
(4) 5/10000
2. Changing process direction
3. Rate or correction
4. Double counting
5. Inch/mm conversion
1-1
1-2
1-3
1-4
2-1
2-1
2-1
2-2
3-1
3-1
3-2
3-2
3-3
3-3
3-5
3-5

6. Initializing
(1) ABS initializing
(2) Program initializing
7. Test
Caution and trouble shooting
1. Caution
2. Trouble shooting
3. Pin information
3-5
3-6
3-6
4-1
4-2
4-3

escription of DSC-Q01 counter

1. Front side
1. Display area
2. Axis selection key
3. Axis-Zero key
4. Power key
5. Number key
6. Function key
shows position value
select present axis
make the display value zero
turn on / off the power
0~9 numbers
calls one of the functions
Keys Description

2. Rear side
1. Power input
2. Connector
DC adapter input
to connect with a scale
Keys Description

3. Connection
Power socket
a linear scale

4. Description of the keys
Axis key
Axis Zero key
Number key
Dot key
+/- key
Function key
Cancel key
ABS function key
Direction key
Enter key
On/Off key
Keys Description
select axis
make the axis zero
input values
decimal point
+ - value conversion
to call function menu
cancel present processing or operation
absolute function at any position
to move in the function or ABS numbers
completion of present process
turn on / off the power

Basic operation

1. Input value / Preset
input
Ex.
input “12.45”
input “-31.25”
2. Display Zero
it shows “0.000”
Ex.
3. ABS / INC conversion (Absolute / Incremental)
ABS designation key
99 ABS numbers can be saved. (1~99)
Move in the numbers by using arrow keys.( )
conversion from INC(normal) to ABS
conversion from ABS to INC(normal)
“ABS 1” is flickering and disappeared.
This means now in “ABS” mode.
“Inc” is flickering and disappeared.
This means now in “INC” mode.
ABS and INC are changed in turn whenever key pushed.

4. Searching for one of the ABS numbers
move by arrow keys
To find ABS number 5
push arrow key until 5 shows
To find ABS number 1
Ex.
push reverse arrow key until 1 shows
To input coordinates of the axis to an ABS number,
type its value or “0.000” while the ABS number is shown.

Function

call function menu
1. Changing resolution (factory setting: 5/1000)
2. Direction change
3. Rate or correction
4. Double counting
5. Inch / mm conversion
6. Initialization
7. Test function
Function

1. Changing resolution (menu>scale)
1. 5/1000
▶ This resolution should be same as the scale’s.
▶ 5/1000 is basic factory setting.
▶ After setting, “0.000” will be shown.
2. 1/1000
▶ This resolution should be same as the scale’s.
▶ 5/1000 is basic factory setting.
▶ After setting, “0.000” will be shown.

3. 1/100
▶ This resolution should be same as the scale’s.
▶ 5/1000 is basic factory setting.
▶ After setting, “0.000” will be shown.
4. 5/10000
▶ This resolution should be same as the scale’s.
▶ 5/1000 is basic factory setting.
▶ After setting, “0.000” will be shown.

2. Direction change (menu>dir)
+ or - direction change
3. Rate or Correction (menu>rAtE)
▶
the real distance and displayed distance.
When there is a difference between
If you input 0.000000,
there will be nothing displayed.
▶
▶ Basic rate is 1.000000
input
1.0 1.0 or 1.000000
flickering
instead, this rate
Rate real distance (dial/block gauge)
displayed distance
(numbers at the readout)
=
input “RATE”

Ex. Real distance is 100mm but
the readout (a display) shows 100.4mm,
flickering
“0.996”
type
4. Double counting (menu>dIA)
diameter ↔ radius
“dIA” is double of the radius

5. Inch / mm conversion (menu>Inch)
6. Initialization / Reset (menu>rESEt)
(1) ABS initialization
Please note that all of the preset
ABS data will be removed.

(2) Program initialization / Reset
Please note that all of the memorized
data including ABS will be removed.
All setting value returns to factory setting.
Factory setting: resolution 5/1000
counting direction
rate 1.000000
unit: mm
radius
7. Test function (menu>tESt)
Check if the LEDs are working well
Counting up from 1 to 8
To cancel the test,
push the CE key.

Caution and trouble shooting