Magnescale LH71 Series User manual

1/3
LH71 Change of display resolution (polarity)
Press key of the axis you want to change and select
the measurement unit resolution.
When you have made your selection, press key to save your settings.
Press key two or three times while the display is .
The display will be (measurement unit resolution).
Press key to check the current length measurement unit resolution.
Press key once while the display is .
The display will be (measurement unit resolution).
Press key to check the current measurement unit resolution.
LH71 Change of display resolution (polarity)
Ver.1 (2021.1) CS&S
* If you do not know the output resolution of the measurement unit, refer to the separate "Initial setup manual".
About 2 sec
For LH71-1, LH71-2 For LH71-3
Press key once to automatically switch to advanced settings mode.
The display will be .
Press key, the display becomes the normal display.
Display of measurement unit resolution (LH71-3)
Purpose of change Operation Explanation
Change the measurement unit resolution Change the length measurement unit resolution in
the basic settings. And check the display resolution
in the detailed settings.
Change the polarity for each input axis
while using the addition function
Change the selection of addition display in the basic
settings
Change the display resolution Change the display resolution in the detailed
settings
Change the display polarity
(Counting direction is reversed)
Change the display resolution in the detailed
settings
Diameter display (double count value) Change to diameter display with display resolution
in the detailed settings
Detailed settings ⇒Display resolution ⇒Change
Detailed settings ⇒Display resolution ⇒Diameter display
LH71-3
The operation method for changing the display resolution differs depending on the purpose and conditions of the change.
Select the purpose and conditions to be changed from the table below and perform the operation.
Basic setting ⇒Measurement unit resolution ⇒Change
Basic settings ⇒Addition display ⇒Change
Detailed settings ⇒Display resolution ⇒Change polarity
Standard Expansion
Extended key
Selection of measurement
unit resolution
Set to basic setting mode.
Turn key “ON” while the AC adapter is energized.
Press and hold key for 3 seconds after the lamp changes from blinking to off.
Basic setting ⇒Measurement unit resolution ⇒Change
About 2 sec
①
② ②
③
④
⑤
Switch from basic settings to normal count mode.
Press key once and the display will change to .
Press key once and the display will change to .
Input 1
Input 2
Input 3
Power ON

2/3
LH71 Change of display resolution (polarity)
Press key to select the conditions for the addition display.
When you have made your selection, press key to save your settings.
With the display , press key once.
The display will be (additional display).
Press key to select the addition display.
Diameter display
(LH71-3 only)
If you press key once, it will automatically enter the advanced setting mode and display.
Press key to enter normal count mode.
Selection of additive display (LH71-3)
* If the display does not change to “Add”, “LATHE” is not selected in “TYPE”.
Input 3 - Input 2
Input 2
Input 3
Input 2 + Input 3
Input 2 - Input 3
- (input 2 + Input 3)
Addition display (input conditions to
be displayed on the Z axis)
Angle display
Length display
NOTE 1: Selection of a value smaller than the basic setting measurement unit
resolution is not displayed.
NOTE 2: The angle display can be set when the angle resolution is selected in
the basic settings.
NOTE 1 NOTE 2
Selection of display resolution
Press key once to display the display resolution of each axis.
Press key of the axis you want to change and select the resolution.
Please note that the lamp lights up once every two times and the diameter display is set.
When you have made your selection, press key to save your settings.
Press key to return to the normal counting state.
Set to the detailed settings mode.
Press key while the normal count mode is energized.
The display will be . (Detailed setting mode)
Set to basic setting mode.
Turn key "ON" while the AC adapter is energized.
Press and hold key for 3 seconds after the lamp changes from blinking to off.
The display will be .
Basic settings ⇒Addition display ⇒Change
Detailed settings ⇒Display resolution ⇒Change
①
②
③
About 2 sec
④
⑤
Switch from basic settings to normal count mode.
Press key once and the display will change to .
Press key once and the display will change to .
Expansion
Extended key
①
②

3/3
LH71 Change of display resolution (polarity)
Before After
Change polarity
Example of changing the polarity of the display in the middle row
Set to advanced mode.
Press key in normal count mode
The display will be .
Press key once to get the display resolution of each axis.
Press key of the axis you want to change to the diameter display and turn on the lamp.
If the resolution changes, press key again.
When you have made your selection, press key to save your settings.
Press key to return to the normal counting state.
Press key once to get the display resolution of each axis.
Press key for the axis for which you want to change the polarity,
and then press key.
When you have made your selection, press key to save your settings.
Press key to return to the normal counting state.
Detailed settings ⇒Display resolution ⇒Diameter display
Detailed settings ⇒Display resolution ⇒Change polarity
①
②
②
Set to advanced mode.
Press key in normal count mode
The display will be .
①
Diameter display