Jensen JE5023 User manual

Guide de l’utilisateur du téléviseur
Veuillez observer toutes les mesures de sécurité en utilisant ce produit.
Veuillez lire soigneusement ce manuel avant d’utiliser ce produit.
Please observe all safety precautions when using this product.
Please read this manual careful
ly.
JE5023
LED TV User’s Guide
LED
hsilgnE
siaçnarF

2
Safety Precautions
Important Information
Important Safeguards
3
4 - 5
10 - 11
User Guidance Information
Part identification (Right View) / Accessories 6
Part identification (Back View) 7
Mounting on a Desktop / Installation Precautions 8
9
Installing an Antenna
Remote control
Precautions / How to use the remote control 12
Connection
VCR Connections / Watching Video Tape 13
Satellite/Cable TV Set-Top Box Connections / Watching Cable TV 14
DVD Connections / USB Connections / Playing the DVD 15
16
Basic Use
Application
Selecting input source / Initial Setup Wizard 17
CONTENTS
Menu Operation 18
19
Customizing the PICTURE Settings
Customizing the TIMER Settings
Customizing the SETUP Settings
Customizing the LOCK Settings
Customizing the CHANNEL Settings
20
22 - 23
24 - 26
27 - 28
..............................................................................
........................................................
.....................................................
....................................................................
............................................................................
....................................................................................
.................................................................................
.......................................................
...............................................................................
............................................
.........................................................................
External Audio Amplifier
.....................................
........................................................
.................................................................
...........................................................
.................................................................
.............................................................
..................................................................
Customizing the AUDIO Settings
21
...................................................................
................................................................
E gn l hsi
USB Settings 29
.....................................................................................
Troubleshooting
Specifications 31
30
.................................................................................
....................................................................................
Maintenance and Service

3
WARNING IMPORTANT SAFETY INSTRUCTIONS
Important Information
To reduce the risk of fire or electric shock,do not expose
this product to rain or moisture.
This symbol is intended to alert the user to the
presence of uninsulated “ dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
This symbol is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
This product utillizes tin-lead solder, and fluorescent lamp
containing a small amount of mercury. Disposal of these
materials may be regulated due to environmental consid-
erations. For disposal or recycling information,please
contact your local authorities or the Electronic Industries
Alliance: www.eia.org.
FCC STATEMENT
FCC CAUTION:
WARNING
This product has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This product generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference
to radio communications.Operation of this equipment in a
residential area is likely to cause harmful interference
in which case the user will be required to correct the
interference at his own expense.
Pursuant to 47CFR, Part 15.21 of the FCC rules, any
changes or modifications to this monitor not expressly
approved by the manufacturer could cause harmful
interference and would void the user’s authority to
operate this device.
This is a CLASS B product. In a domestic encironment,
this product may cause radio interference, in which cause
the user may be required to take adequate measures to
counter interference
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this product near water.
Apparatus should not be exposed to dripping or
splashing and no objects filled with liquids, such
as vases, should be placed on the product.
6) Clean only with a dry cloth.
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instrutions.
8) Do not install near any heat sources
such as radiators, heat registers,
stoves, or other apparatus(including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade
or the third prong are provided for your safety.
If the provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
10) Protect the power cord from being walked on or
pinched, particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11) Only use attachments / accessories specified by
the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer or sold with
the apparatus.
when a cart is used, use caution when
moving the cart / apparatus combination
to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms
or when unused for long periods of time.
14) Refer all servicing to qualified service
personnel.Servicing is required when the
product has been damaged in any way, such as
power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the
product, the product has been exposed to rain
or moisture, does not operate normally, or has
been dropped.
15) Where the mains plug or an appliance coupler is
used as the disconnect device, the disconnect
device shall remain readily operable.
E gn l hsi

English
4
Important Safeguards
Before using your TV, please read these instructions
completely, and keep this manual for future reference,
Carefully observe and comply with all warnings,
cautions and instructions placed on the unit or
described in the operating instructions or service
manual.
WARNING
Power Sources
Grounding or Polarization
Overloading
Power
Sound
Power Cord
Ventilation
Heat sources
For the unit with a polarlzed AC power cord plug
For the unit with a DC power connector
Wall outlet
Wiring
Electric shock
Cleaning
To guard against injury, the following basic safety
precautions should be observed in the installation,
use and servicing of the unit.
This unit should be operated only from the type of
power source indicated on the information label.
If you are not sure of the type of electrical power
supplied to your home, consult your dealer or local
power company.
This unit is equipped with a polarized AC power cord
plug (a plug having one blade wider than the other), or
a DC power connection, for use in a vehicle. Follow
the instructions below:
This plug will fit into the power outlet
only one way.This is a safety feature.
If you are unable to insert the plug fully
into the outlet, try reversing the plug.If the plug still fails
to fit, contact your electrician to have a suitable outlet
installed. Do not defeat the safety purpose of the
polarized plug by forcing it in.
For installation in a vehicle, connect the red wire to the
12V accessory line and the black wire to ground terminal.
Do not use a poor fitting outlet.
Insert the plug fully into the outlet. If it is loose, if may
cause arcing and result in fire. Contact your electrician
to have the outlet changed.
For your safety, unplug the power cord when wiring
cables.
Do not touch the AC power cord or the unit with a wet
hand. If you plug / unplug the AC power cord from the
unit with a wet hand, it may cause electric shock.
Never attempt to move the unit unless the AC power
cord is disconnected.
Clean the power plug regularly.
If the plug is covered with dust and it picks
up moisture, its insulation may deteriorate
and result in fire.
Unplug the power plug and clean it regularly.
Unplug the power cord when cleaning this unit. If not,
it may result in electric shock.
Clean the cabinet of the TV with a dry soft cloth. To
remove dust from the screen, wipe it with a soft cloth.
Stubborn stains may be removed with a cloth slightly
dampened with a solution of mild soap and warm water.
Never use strong solvents such as thinner or benzine for
cleaning.
If using a chemically pre-treated cloth, please follow the
instructions provided on the package.
Always turn the unit off when it is not being used.
When the unit is left unattended and unused for long periods
of time, unplug it from the wall outlet as a precaution against
the possibility of an internal malfunction that could create a fire
hazard.
Do not overload wall outlets, extension cords or convenience
receptacles beyond their capacity, since this can result in fire
or electric shock.
If a snapping or popping sound from the TV is continuous or
frequent while the TV is operating, unplug the TV and consult
your dealer or service technician. It is normal for TV’s to make
occasional snapping or popping sounds, particularly when
being turned on or off.
If you damage the power cord, it may result in fire or electric
shock.
Do not pinch, bend, or twist the cord excessively.The core
lines may be bared and cut and cause short-circuit, resulting
in fire or electric shock.
Do not convert or damage the power cord.
Do not put anything heavy on the power cord.
Do not pull the power cord.
Keep the power cord away from heat sources.
Be sure to grasp the plug when disconnecting the power
cord.
If the power cord is damaged, stop using it and replace
with a new one.
The slots and openings in the TV are provided for necessary
ventilation. To ensure reliable operation of the unit, and to
protect it from overheating, these slots and openings must
never be blocked or covered. Unless proper Yentilation is
provided, the unit may gather dust and get dirty. For proper
ventilation, observe the following:
Do not install the unit turned backward or sideways.
Do not install the unit turned over or upside down.
Never cover the slots and openings with a cloth or other
materials.
Never block the slots and openings by placing the unit on a
bed, sofa, rug or other similar surface.
Never place the unit in a confined space, such as a bookcase
or built-in cabinet, unless proper ventilation is provided.
Leave some space around the unit. Otherwise, adequate
air-circulation may be blocked, causing overheating, and
may cause fire or damage the unit.
Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.

5
Important Safeguards
E gn l hsi
Do not use this product near water Safety checks
Wall or ceiling mounting
Panel protection
Pixel defect
Antennas
Outdoor Antenna Grounding
WHEN INSTALLING AN OUTDOOR ANTENNA SYSTEM,
EXTREME CARE SHOULD BE TAKEN TO KEEP FROM
CONTACTING POWER LINES OR CIRCUITS AS
CONTACT WITH THEM IS ALMOST INVARIABLY FATAL.
Entering of objects and liguids
Lightning
Servicing
Replacement parts
Attachments
Damage reguiring service
Do not use near a bathtub, washbowl, kitchen sink, or laundry
tub, in a wet basement, or near a swimming pool.
Do not use immediately after moving from a low temperture
to high temperature environment, as this cause condensation,
which may result in fire, electric shock, or other hazards.
This product should not be exposed to dripping or splasing
and no objects filled with liquids, such as vases, should be
placed on the product.
Never insert an object into the product through vents or
openings. High voltage flows in the product, and inserting
an object can cause electric shock and / or short internal
parts. For the same reason, do not spill water or liquid on
the product.
Unplug this apparatus during lightning storms or when
unused for long periods of time.
For added protection during a lightning storm, or when
left unattended and unused for long periods of time,
unplug the product from the wall outlet and disconnect
the antenna. This will prevent damage to the equipment
due to lightning and power-line surges.
Refer all servicing to qualified service personnel. Servicing
is required when the product has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
In case the product needs replacement parts, make sure the
service person uses replacement parts specified by the
manufacturer, or those with the same characteristics and
performance as the original parts. Use of unauthorized parts
can result in fire, electric shock and / or other danger.
Only use attachments / accessories specified by the
manufacturer. Do not use attachments not recommended
by the manufacturer. Use of improper attachments can
result in accidents.
If any of the following conditions occurs, unplug the power
cord from the AC outlet and request a qualified service
person to perform repairs.
a. The power cord or plug is damaged.
b. Liquid is spilled on the product or when objects have
fallen into the product.
c. The product has been exposed to rain or water.
d. The product does not operate properly as described
in the operating instructions.
Do not touch the controls other than those described
in the operating instructions. Improper adjustment of
controls not described in the instructions can cause
damage,which often requires extensive adjustment
work by qualified technician.
e. The product has been dropped or the cabinet has been
damaged in any way.
f. The product displays an abnormal condition or exhibits
a distinct change in performance. Any noticeable
abnormality in the product indicates that the product
needs servicing.
Upon completion of service or repair work, request the
service technician to perform safety checks to ensure
that the product is in proper operating condition.
When mounting the product on a wall or ceiling, be sure
to install be product according to the method recommended
by the manufacturer.
This panel used in this product is made of glass.
Therefore, it can break when the product is dropped
or impacted upon by other objects. Be careful not to
be injured by broken glass pieces if the panel breaks.
Occasionally, a few non-active pixels may appear on
the screen as a fixed point of blue,green or red. Please
note that this does not affect the performance of your
product.
If an outdoor antenna is installed, follow the precautions
below. An outdoor antenna system should not be located
in the vicinity of overhead power lines or other electric light
or power circuits, or where it can come in contact with such
power lines or circuits.
Be sure the antenna system is grounded to provide
some protection against voltage surges and built-up
static charges.Section 810 of the National Electrical
Code ( NEC ) in USA and Section 54 of the Canadian
Electrical Code in Canada provides information with
respect to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors, location
of antenna discharge unit,connection to grounding
electrodes, and requirements for the grounding
electrode.
NEC: National Electrical Code
Antenna Grounding According to the National
Electrical Code, ANSI/NFPA 70
Antenna lead-in wire
Ground clamps
Ground clamps
Antenna discharge unit
( NEC Section 810-20)
Grounding conductors
( NEC Section 810-21)
Power service grounding
electrode system
(NEC Art 250 Part H)
Electric service
equipment

Part Identification
Accessories English
Right View
Remote Control
Audio Out Cable
x
User Guide Information
The configuration of the components may look different from the following illustration.
6
MENU Button-OSD Menu Display Button
CH- / CH+ Button
VOL- / VOL+ Button
SOURCE Button
POWER Button

Part Identification
Back View
E gn l hsi
8
2
2. AUDIO OUTPUT
8. HEADPHONE4. RF IN
3. HDMI
6. AV in (Video and Audio)
7. USB Port
1. AC IN 5.
7
1
23 3 3 4
5
6
7
8
5V
5V 500mA
Y Pb Pr-Component Video Input

English
User Guide Information
Mounting on a Desktop
Wall Mounting
Using the Stand
Installation Precautions
1 1
1
1
1
Your LED TV can be mounted on a desktop with the base installed.
This is not a floor-standing unit.
Please refer to diagrams A and B.
Please ensure enough space for safe use.
Installation of the LED TV in an improperly ventilated location can cause damage to the LED TV
due to increased temperature.
(Mounting on a wall)
(Using the Stand)
Contact your dealer to purchase the Adjustable-angle wall mount required for wall-mounted installation.
Do not install on an unstable location with a support area smaller than the LED TV.
Please refer to the desktop stand user＇
s manual for details of installation.
8

9
Installing an Antenna
Use a coaxial cable to connect the wall jack or external antenna to the RF-IN on the LED TV
Press the SOURCE button on the remote control to select TV, then press RIGHT button to confirm.
Then you can receive the ATSC/NTSC signal.
Wall Jack with
F-Connector
Coaxial (Round) Antenna Cable Analog+Digital 75
User Guide Information
For connecting to ATSC or NTSC broadcast
E gn l hsi

Remote Control
10
English s i l g n E
Activate TV Mode
POWER On / off for TV and DVD
PREVIOUS
EJECT (DVD)
FAST REVERSE
STOP
T/F (DVD)
ZOOM (DVD)
AUDIO (DVD)
SET UP (DVD)
F-LIST Press this button to display the favourite list
Press C-LIST button to display the channel list
C-LIST
SLEEP Cycles through the LED TV sleep time:off / 5 /
CC Closed Captions
MENU Displays the OSD menu on the screen
Move up, down, left or right
NAVIGATION
EPG Displays the program guide
Exits the current menu.
CH+/CH- Increase or Decrease channel
NUMERIC KEYS
SOURCE Displays AV Inputs
DVD
TV
Activate DVD Mode
FAST FORWARD
NEXT
RPT Repeat Selection
SUB-T (DVD)
Display Time or Chapter information
DISP (DVD)
EQ (DVD)
TITLE (DVD)
MTS/SAP Press MTS/SAP to select Stereo, SAP or Mono
SOUND Press SOUND to cycle select sound
Press PICTURE to cycle select picture
PICTURE
INFORMATION Press INFO to display information
about the current channel.
SCALE
Cycles scale modes: Wide, Zoom, Cinema, Normal.
ENTER Press ENTER to confirm your opeartion
EXIT
VOL+/VOL- Increase or Decrease volume
MUTE Press once mutes audio, press again to restore audio
RETURN Return to previously viewed channel
Digital channel selection
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
types: Standard / Music / Movie / Personal.
10 / 15 / 30 / 45 / 60 / 90 / 120 / 180 / 240 minutes
types: Standard / Dynamic / Soft / Personal
1
456 7
910 11
8
13 14 15
12
17 18 19
16
21 22 23
20
25
29
31
35
36
38
39 40
26 27
30
24
28
33
37
32
34
23
LAY/PAUSEP
Funtions of remote control buttons
User Guide Information

Remote Control
11
NOTE: DVD functions are intended for JENSEN DVD players only.
See your JENSEN DVD manual for more information.
POWER
CH
VOL
RETURN
MUTE
MENU
INFO
ENTER
SOURCE
EX IT
EPG
1
2
3
POWER POWER
CH+
CH-
VOL+
VOL-
VOL+
VOL-
RETURN
MUTE
MENU
INFO
UP UP
DOWN DOWN
LEFT LEFT
RIGHT RIGHT
ENTER OK
SOURCE SOURCE
EXIT
EPG
T F T-F
1
EJECT
1
2 2
3 3
PICTURE
PICTURE
TITLE
SOUND
SOUND
EQ
F-LIST F-LIST
AUDIO
C-LIST
C-LIST
SETUP
SLEEP
DISP
CC
SUB-T
SCALE
SCALE
ZOOM
4
5
6
7
8
9
00 0
9 9
8 8
7 7
6 6
5 5
4 4
RPT
NEXT
FAST-FORWARD
FAST-REVERSE
PREVIOUS
PLAY-PAUSE
STOP
FAST-REVERSE
PREVIOUS
PLAY-PAUSE
STOP
BUTTON TV-FUNCTION DVD-FUNCTION TV-FUNCTION DVD-FUNCTION TV-FUNCTION DVD-FUNCTION
BUTTON
ZOOM
SUB T
DISP
SETUP
AUDIO
EQ
TITLE
SLEEP
CC
RP T
BUTTON
MTS-SAP
MTS/SAP
MUTE
MENU NEXT
RPT
FAST-FORWARD
User Guide Information
E gn l hsi

Precautions
Avoiding Remote Control Problems
Inserting Batteries in the Remote Control
12
How to use the remote control
English
3. Replace the cover.
CAUTION: Risk of explosion if battery is replaced by incorrect type.
Dispose of used batteries according to national code (Recycling program).
Used batteries should be disposed of properly.
The remote control should be operated within 30 feet (7m) and 300to the left and the right of the IR receiver
at the front of the LED TV.
1. Check the polarity (+,-) of the batteries in the remote control.
2. Check that the batteries are good.
1. Open the cover completely.
2. Insert the two supplied batteries (AA, 1.5V). Ensure that the polarities (+ and -) of the batteries are aligned
correctly.
User Guide Information

SOURCE
3.Press to confirm the source selection ,
4.Turn on the VCR, insert the tape and press the play button.
ENTER
VCR Connections
Watching Video Tape
13
Terminals vary by manufacturer
(Included)
Connect the LED TV’s Composite In terminal to VCR’s Composite OUT terminal using the included Composite cable.
English
will automatically enter the selection mode.
Connecting to the Composite terminal
(Make sure the color of the terminals and the colors of the cable are the same.)
1.Turn on the LED TV and press on the remote control.
2. Use to move to AV.

Satellite / Cable TV Set-Top Box Connections
Watching Cable TV
14
Terminals vary by manufacturer
In order to watch Cable TV, Subscribe to your local Cable TV company and install a separate receiver (Set-Top Box)
HDMI Cable (Not Included)
English
Connect the LED TV’s Composite In terminal to the cable broadcasting receiver Composite Out terminal using the
Composite cable. (Make sure the color of the terminals and the color of cables are the same)
(Included)
Connecting tothe Composite terminal
Connecting tothe HDMI terminal
SOURCE
3.Press to confirm the source selection.
4.Turn on the cable broadcasting receiver and select the channel you wish to view.
ENTER
1.Turn on the LED TV and press on the remote control.
2. Use to move to AV . If HDMI has been connected, select HDMI .

Connection
15
English
USB Connections
Connection to USB.
Note: This USB connection can be used for software up
DVD Connections
Terminals vary by manufacturer
Playing DVDs
4.
3. Stop operation a few seconds, will automatically enter the selection mode.
Turn on the DVD player, insert the DVD disc and press the Play button.
Turn on the LED TV and press the source button.
HDMI Cable(Not Included)
Connecting to the HDMI terminal
Connecting to the component terminal
1. Connect LED TV’s YPbPr (Component) terminal to DVD’ s Video Out terminal.
.lanimrettuOoiduAs’DVDotslanimretoiduAs’VTDELtcennoC.2
3. It must match the component connection cable Y, Pb, Pr colors between the LED TV and DVD Player.
grade and using the USB media (Audio + photos) player.
Press Source to cycle and select .If HDMI has been connected, select HDMIComponent .
(Not Included)
Component Video Cable (Not Included)
5V 500mA

16
English
External Audio Amplifier
Connecting to an amplifer or home theater system.
Terminals vary by manufacturer.
Connect the LED TV’s AUDIO output terminal to Audio Amplifier using an audio patch cable.
Note: The speakers of LED TV still have output audio signal at this time.
You can use the Volume +/- buttons to adjust the audio output level.
(Included)
Left Channel Audio Right Channel Audio
Common

17
Selecting Input Source
Note: After you have selected the desired input sorce and pause for a few moments,
then LED TV will automatically enter the seleted mode.
Initial Setup Wizard
Setup Wizard
Air/Cable
Cable System
Auto Scan
English
Cable
STD
Select Move Exit
MENU
Menu Language
After connecting your TV antenna or Coaxial cable, turn the television
The quick setup wizard will display on-screen. Select your preferred
language followed by antenna options and performing Auto Scan to receive
local broadcast channels that will be stored in the TV tuner memory.
dnuofslennahC.nacSotuAlennahCehtnurdnasnoitpoannetnatcelesotunemVTehtotuoytceridlliwdraziwehT
will be stored in the TV tuner memory.
How to N a vig a te:
Press the•
Press the•
arrow button to highlight Menu Language and then press
arrow button to highlight CABLE /
AIR based on your antenna connection.
Press the• arrow button to select Auto Scan and press (when Cable is selected, ‘AUTO’ is
recommended). Otherwise, press the arrow button to select Cable System .otuA>CRH>CRI>DTS:
button to select OSD Language.
arrow
ON.
Press button on the remote control.
Use to move to the desired input source.
Press to select.
You can select between the TV signal and the input signal of other equipment connected to the TV.
Use this function to switch to the input source you wish to view.
E gn l hsi
Enter

Setu p Lo ck
12
6
Time
Pi ct ur e
Ch an ne l
Ch ange Pas sword
Sy stem Loc k
US
Ca nada
Rese t RRT
RR T Setting
Mo ve Exit
MENU
On
TIME MENU:
Allows you to set up a variety of time options.
LOCK MENU:
Allows you to set up a variety of lock options.
SETUP MENU:
Allows you to set up a variety of setup options.
CHANNEL MENU:
Allows you to search channels and set up a variety of channel options.
Allows you to customize the sound options and effects.
Allows you to make adjustments to your picture settings.
Use the LEFT and RIGHT buttons to select your main menu option.
Press the MENU button to exit submenu to return to the main menu.
Press the MENU button again or EXIT button to exit the main menu.
Menu Operation
Note: Some options are not available for all inputs.
Use the UP / DOWN buttons to select an option of the sub-menu, and press the RIGHT button.
While in adjustment mode, use the LEFT / RIGHT buttons to change the value of the item.
Setu p Lo ck
12
6
Time
Pi ct ur e
Chan ne l
Au to Scan
Fa vorite
Sh ow Hide
Ch annel No
Ch annel Label
DT V Signal
Air
Select Mov e Exit
MENU
50 3
KO CE LB
Go od
Air/Cable
Audio
Audio
AUDIO MENU:PICTURE MENU:
4
5
Setu p Lo ck
12
6
Time
Pict ur e
Chan ne l
Pi cture Mo de
Co ntrast
Br ightne ss
Co lor
Tint
Sh arpnes s
Co lor
Standard
Normal
Select Mov e Exit
MENU
50
50
50
0
50
Audio
HDMI CEC
Setu p Lo ck C han ne l
Sl eep Tim e
Time Zone
Clock
Da ylight S aving Time
Select Mo ve Exit
MENU
Pi ct ur e
Of f
Pacific
Of f
2016/6/22
12
6
Time
Audio Lock
12
6
Time Cha nn el
Me nu Langua ge
Tra nspare ncy
Zo om Mode
No ise Redu ction
Cl osed Cap ation
Au dio
Re store De fault
English
Select Mo ve Exit
MENU
Pi ct ur e
Off
Normal
Off
Setu p
Audio
OUT Fixed
Next
18
deoM
Press the MENU button on the remote control, the on-screen menu will appear.
Press the POWER button to turn the LED TV on.
Application
Guide available @ www.jensenrvdirect.com/manuals-guides
English
Setu p Lo ck
12
6
Time C ha nn el
So und Mode
Bass
Tre ble
Ba lance
AVC
Au dio Lang uage
Standard
En glish
Select Mov e Exit
MENU
50
50
50
Of f
Of f
Pi ct ur e
Audio
TV Speaker
Accessibility

19
Picture Mode Cycles through picture display modes: Standard, Dynamic, Soft, Personal.
Contrast Controls the difference between the brightest and darkest regions of the picture.
Brightness Controls the overall brightness of the picture
Color Controls the color.
Tint Controls the tint.
Sharpness Increase this setting to see crisp edges in the picture; decrease it for soft edges .
Color Mode Cycles through color modes: Normal, Cool, Warm.
HDMI CEC
Customizing the PICTURE Settings
Select TV source for example. (Press SOURCE button to select TV mode)
1. Press the POWER button to turn the LED TV on
2. Press the MENU button on the remote control to display the Main menu, and use the LEFT and RIGHT
buttons to select the PICTURE.
3. Use the UP and DOWN buttons to highlight an individual PICTURE options, use the LEFT and RIGHT
buttons to change the setting, and press the MENU or EXIT button to exit.
The PICTURE menu includes the following options :
Application
E gn l hsi
If you turn off the CEC Mode then the following items (TV Auto Power,TV Auto
Switch,Device Auto Standby) will not be used.
On-TV will turn on when compatible CEC device is activated on HDMI
connection.
TV Auto Switch On-TV will switch to HDMI inputs when compatible CEC device
is activated on HDMI connection.
Device Auto Standby
On-When TV turned off, any connected, compatible CEC device will
also turn off.
TV Auto Power
Set up L oc k
12
6
Tim e
Pi ctu re
Cha nn el
Selec tMo ve MEN U
Audio
CEC Mode
TV Auto Power
TV Auto Switch
Device Auto Standby
On
On
On
Audio Receiver On
On
Return
Audio Receiver Enables audio to be sent to an HDMI connected AV receiver.
Setup Lo ck
12
6
Time
Pictur e
Channel
Picture Mode
Contrast
Brightness
Color
Tint
Sharpness
Color
Standard
Normal
Select Move Exit
MENU
50
50
50
0
50
Audio
HDMI CEC
deoM
Guide available @ www.jensenrvdirect.com/manuals-guides

20
Sound Mode Cycles through sound modes: Standard, Music, Movie and Personal.
Bass Controls the relative intensity of lower pitched sounds.
Treble Controls the relative intensity of higher pitched sounds
Balance To adjust the balance of the left and right sound track, or turn off the volume of the
left and right sound track.
TV Speaker Allows you to select between ON and OFF.
AVC On or off (Automatic Volume Control) to keep volume level steady.
Audio Language Allows you to select preferred audio languages: English, French and Spanish.
Accessibility Audio assist for the blind.
Customizing the Audio Settings
Select TV source for example. (Press SOURCE button to select TV mode)
1. Press the POWER button to turn the LED TV on.
2. Press the MENU button on the remote control to display the Main menu, and use the LEFT and RIGHT
buttons to select the AUDIO.
3. Use the UP and DOWN buttons to highlight an individual Audio options, use the LEFT and RIGHT
buttons to change the setting, and press the MENU or EXIT button to exit.
The SOUND menu includes the following options :
Application
Setup L ock
12
6
Time Ch ann el
Sound Mode
Bass
Treble
Balance
AVC
Audio Language
Standard
English
Select Move Exit
MENU
50
50
50
Off
Off
Pi ctu re
Audio
TV Speaker
Accessibility
E gn l hsi