Jetview JE-900 series User manual

JE-900 series PTZ Camera
Operation Guider

I、Connecting diagram
1-1 For the high speed dome camera with alarm function (JE-900H)
1-2 For the low spped dome camera without alarm function (JE-900L, IR800)

1-3 Note of installing
RS485 is polarity, it must be connected Positive to Positive, negative to Negative
For the AC adaptor, the best way is put it into the alarm mounting for insuring enough power
to feed the camera
II、JE-900 series PTZ camera General Functions (exclude camera module)
1. Adopting multi-functional high-performance DSP design with stable performance
2. Integrated design with compact structure and high reliability
3. Precise electric motor drive ensuring smooth running and agile reaction
4. The internally saved data will not be lost1 year since power off
5. Pelco Protocol built-in
6. RS485 bus communication
7. 64-128 preset positions for random storage and accurate locating
8. 4 tour groups, 16 preset positions can be stored in each tour group
9. Support Left & Right scan function, Low, Medium and High 3-levels speeds optional
10. The unit has a default position
11. 4 channels alarm in, 1 channel alarm out
12. Pan 360°consecutive movement, no blind area for the monitoring
13. Tilt 90°, auto flip at the bottom, which ensures consecutive monitoring
14. Automatically adjusting movement speed according to lens zoom ratio
15. Manual Fog-dispersing Function is realized.
Note
Item7, 64 presets for low speed model , 128 presets for high speed model
Item11 is for high speed model.
Item13 auto flip is for high speed model
Item15 is for special order
III、The fixed code and its function guide
There are inherent codes stored in the camera, each code with its special function, user can invite or call
it to operate the camera

The special inherent code and it's function
Code
Functions
Code
Functions
130
Set left position
146
Exit Menu
131
Set right position
147
Activate Alarm Function
132
Cruising between two point with L-Speed
148
Disable Alarm Function
133
Cruising between two point with M-Speed
150
Preset Position Restore
134
Cruising between two point with H-Speed
160
Begin L/R limit position setup
135
360 °cruising with L-Speed
161
Exit L/R limit position setup
136
360 °cruise with M-Speed
162
Enable default position
137
360 °cruise with H-Speed
163
Disable Default position
140
Tour group Setup
164
Setup a Default Position
141
Exit Tour group Setup
165
Activate Fog Dispersing
142
Run a tour group
166
Exit Fog Dispersing
145
Enter Camera Block's menu
95
Enter Dome OSD Menu
Note:
1. Code 147,148 is for the camera with alarm function.
2. Code 160, 161 is special for low speed camera
3. Code 165,166 and 95 is for special order
4. above code is fixed and stored in the camera, you must enter the code number and key “preview”
( some controller named invoke, call or function key) on controller for its function.
The code on the above table is the important details for operation the camera.
3-1 Setup and Preview Preset Positions
The camera can store the current pan, tilt and zoom position with relative number, you can quickly
preview those positions when you needed, Users can use the devices as keyboard controller to save
and preview preset positions fast and conveniently. The JE 900 series speed dome camera can store up
to 128 preset positions.
Setup preset positions
After move (pan, tilt and zoom) the camera to the position you want to monitor, enter a number for
the code of preset position and press the “PRESET” key, then you have done successfully.
Example: Set up preset position No.1
a. Use the joystick to move the dome camera to the desired position.
b. Enter “1”
c. Press the “PRESET” key

Preview Preset Positions
The function can command the camera to quickly return to the preset position you set.
Enter the number you need to preview, Press the “PREVIEW” key, then the dome camera returns to
the preset position.
Example: Preview Preset position No.2
a. Enter “2”
b. Press the “PREVIEW” key
The camera will go to the preset 2 immediately
3-2 Setup and running of Tour group
User can program the preset positions into the automatic tour in the required order, when necessary,
run the tour group, the camera will automatically scan the preset positions set in the tour consecutively
and circularly. Up to 16 preset positions can be saved in one tour group.

The code 140, 141, 142 is special for setup and run a tour group
“142” + “PREVIEW” key for command the camera to tour.
“140” + “PREVIEW” key for programming a tour group.
“141” + “PREVIEW” key for exiting the setup.
For Example, Program a tour in order to scan 1→2→5→3→4→6 preset (preset 1, 2, 3, 4, 5, 6, was set
successfully). The steps is as below:
1. Key “140” + “PREVIEW” to start a tour setup
2. Key “1” + “PREVIEW” for the First tour position
3. Key “2” + “PREVIEW” for the Second tour position
4. Key “5” + “PREVIEW” for the Third tour position
5. Key “3” + “PREVIEW” for the Fourth tour position
6. Key “4” + “PREVIEW” for the Fifth tour position
7. Key “6” + “PREVIEW” for the Sixth tour position
8. Key “141” + “PREVIEW” to exit tour setup
9. Key “142” + “PREVIEW” to command the camera to tour, the dome camera will be in order
of 1→2→5→3→4→6 to scan.
Dwell time, and more one tour groups setup, please refer the controller menu to do.
3-3 Setup and scan between two points
The user can freely set a beginning point as the Left Limiting Position, an end point as the Right
Limiting Position. Meanwhile, the user can also set the zoom times on the position, the camera only
store the parameters on the beginning point. (Attention: If the beginning point is the same as the end
point, the dome will scan 360°) The operation is as below:
For High speed dome camera(JE900H series)
a. Set up the Left Limited Position: Operate the joystick towards left, adjust the image to the desired
position, then key 130 + Preview on controller
b. Set up the Right Limiting Position: After the Left Limiting position is set up well, operate the joystick
towards right, adjust the image to the desired position, then key 130 + Preview on controller

For low speed dome camera(JE900L series)
a. Key “160 + PREVIEW” key to activate the function for setup of left/right limited positions
b. Control the dome camera by joystick, moves it to the right direction and reaches the desired point as
a right limiting position, then Key “131 + PREVIEW” key, now the right limited position has been
done successfully. As the same, you can do left limited position setup with key “130 + preview”.
c. Key “161 + PREVIEW” to exit the setup. Now the setup of left/right limited positions is completed.
After you did above, you can command the camera to scan between tow points with below code
1. Key “132 + Preview” on controller, the camera will scan between two points with low speed
2. Key “133 + Preview” on controller, the camera will scan between two points with medium speed
3. Key “134 + Preview” on controller, the camera will scan between two points with high speed
3-4 Start 360°scanning function of the Pan/Tilt
The Camera can be 360°endless horizontal scanning for all-direction monitoring. Three speeds can be
optional: “135” for low speed, “136”for medium speed, “137”for high speed.
3-5 Setup, Activate and Exit Default Position
The unit has a default position. The user can set up default position for a key monitoring area
according to actual requirement. The function means that the dome camera will automatically move to
the default position for monitoring If it is not operated after 5 minutes.
1. Setup of the Default Position
Move the dome camera to a key monitoring area by joystick, enter number “164” and press the
“PREVIEW” key, then the setup is successful.
2. Activate and Exit the Default Position function
Enter number “162” and press “PREVIEW” key for enabling the function.
Enter number “163” and press “PREVIEW” key for disabling the function.

3-6 Setup, Activate and Exit alarm function
The diagram of alarm connecting is as following. With the alarm function, the camera auto tours up
to 4 areas where need to motion, once the one of alarm sensors is triggered, the camera will rapid run
and stay toward the where motion detected.
Alarm output connection sketch
Connection sketch for Alarm input with Usual-closed detector

Connection sketch for Alarm input with Usual-open detector
How to operate alarm function
Step 1: Setup at alarm preset positions.
Setup preset position 1 for alarm 1
Setup preset position 2 for alarm 2
Setup preset position 3 for alarm 3
Setup preset position 4 for alarm 4
Step 2: Setup an alarm cruising group.
All alarm preset positions (preset position 1~4) must setup in the same group.
Step 3: Running alarm tour
Enter “142+ preview” on keyboard controller to start the alarm preset cruising.
Step 4: Run and exit alarm system

Enter “147+ preview” on keyboard controller to enable the alarm function,
Enter number “148+ preview” on keyboard controller to disable the alarm function,
Attention:
a. Alarm input must be ON/OFF input signal, any other type of input signal (such as power voltage etc)
is possible to damage the unit. When there are alarm signals from multi-channels, the unit will respond
to them one by one, the interval is 2 seconds.
b. Once there is alarm signal coming in, the unit will not respond to “Scan”, “Cruising” etc functions.
Manual operation is needed to restore “Scan”, “Cruising” etc functions.
c. Whether the alarm function is enabled or not, the alarm output always responds. For example, under
the alarm function is inactive mode, the camera will not move to the position alarm triggered, but the
alarm output still responds.
e. A 2.2KΩ resistor must be connecting for the channel without detector, otherwise the camera will
thinks that there is alarm signal coming in, thus the alarm output is always on.
3-7 Configure the camera module parameter
Key “145 + Preview”on controller for enter into camera module OSD menu
Key “146 + Preview”on controller for exit OSD menu
Enter “145 + preview” on the keyboard, then camera module OSD menu will be popped on the the
screen for setting

IV、Protocol, Baud Rate and Camera ID setup
It is important to know how to setup the protocol, baud rate and camera, the camera can be controlled by
controller that is both of them with same protocol, baud rate and camera ID
4-1 For the low speed series(JE900L)
There are two Dip-switches on the circuit board, SW1 8 bit switches for setup the camera ID and baud
rate, SW2 6 bit switches for setup protocol, the setup diagram is as below:
Camera ID Setting Chart
No.
654321
No.
654321
No.
654321
No.
654321
1
000001
18
010010
35
100011
52
110100
2
000010
19
010011
36
100100
53
110101
3
000011
20
010100
37
100101
54
110110
4
000100
21
010101
38
100110
55
110111
5
000101
22
010110
39
100111
56
111000
6
000110
23
010111
40
101000
57
111001
7
000111
24
011000
41
101001
58
111010
8
001000
25
011001
42
101010
59
111011
9
001001
26
011010
43
101011
60
111100
10
001010
27
011011
44
101100
61
111101

11
001011
28
011100
45
101101
62
111110
12
001100
29
011101
46
101110
63
111111
13
001101
30
011110
47
101111
14
001110
31
011111
48
110000
15
001111
32
100000
49
110001
16
010000
33
100001
50
110010
17
010001
34
100010
51
110011
4-2 For the high speed series(JE900H)
There are two Dip-switches beside inside cover, SW1 8 bit switches for setup the camera ID and baud
rate, SW2 4 bit switches for setup protocol (1, 2) and Baud Rate(3, 4). The setup diagram is as below:
Camera ID Setting Chart
1-93
No.
87654321
No.
87654321
No.
87654321
1
00000001
32
00100000
63
00111111
2
00000010
33
00100001
64
01000000
3
00000011
34
00100010
65
01000001
4
00000100
35
00100011
66
01000010
5
00000101
36
00100100
67
01000011
6
00000110
37
00100101
68
01000100
7
00000111
38
00100110
69
01000101
8
00001000
39
00100111
70
01000110

9
00001001
40
00101000
71
01000111
10
00001010
41
00101001
72
01001000
11
00001011
42
00101010
73
01001001
12
00001100
43
00101011
74
01001010
13
00001101
44
00101100
75
01001011
14
00001110
45
00101101
76
01001100
15
00001111
46
00101110
77
01001101
16
00010000
47
00101111
78
01001110
17
00010001
48
00110000
79
01001111
18
00010010
49
00110001
80
01010000
19
00010011
50
00110010
81
01010001
20
00010100
51
00110011
82
01010010
21
00010101
52
00110100
83
01010011
22
00010110
53
00110101
84
01010100
23
00010111
54
00110110
85
01010101
24
00011000
55
00110111
86
01010110
25
00011001
56
00111000
87
01010111
26
00011010
57
00111001
88
01011000
27
00011011
58
00111010
89
01011001
28
00011100
59
00111011
90
01011010
29
00011101
60
00111100
91
01011011
30
00011110
61
00111101
92
01011100
31
00011111
62
00111110
93
01011101
V、Specification
5-1 High Speed Dome
Pan/ Tilt
Pan speed
Manual control
0.5º-200º/s (64 ranges)
Max. Speed
400°/s
Pan movement
360°endless/ 90°
Tilt movement
90°
Preset Position
128 pcs
Tour Groups
4 groups (16 preset positions in each)
Scan Speed
128 ranges adjustable
Automatic flip
Automatic 180ºflip when vertical 90º
Speed Auto-control
can automatically adjust the running speed following the
change of the focal length.
Default Position function
Yes

Scan between 2 points
Yes
General
Power Supply
DC14~30V(2A), AC18~30V (2A)
operation temperature
0ºC～40ºC/ -40ºC ～60ºC (with heater/fan)
Relative humidity
≤95% non-condensing
Power consumption
20W
Protocol
Pelco-D and Pelco-P
Communication System
RS485Bus
Baud Rate(RS485)
2400bps, 4800bps, 9600bps
Dwell time at each position
1~255 adjustable
Camera address range
1-255
Alarm
4 Channels in, 1 Channel out
Fog Dispersion function
Optional
Fan/ Heater
Working range >50 ºC or < -5 ºC
5-2 Low Speed Dome
Pan / Tilt
Highest Pan speed
20°/s
Pan speed
5°-20°/s
Pan/ Tilt movement
360°endless/ 90°
Preset Position
64
Cruise Tracking Group
4 groups (16 preset positions in each)
Scan Speed
High/ Medium/ Low 3 levels optional
Default Position function
Yes
Scan between 2 points
Yes
General
Power Supply
DC12~15V(2A)
operation temperature
0ºC~40ºC/ -40ºC ~60ºC (with heater/fan)
Relative humidity
≤95% non-condensing

Power consumption
20W
Protocol
Pelco-D and Pelco-P
Communication System
RS485Bus
Baud Rate(RS485)
2400bps, 4800bps, 9600bps
Dwell time at each position of tour
1~255 adjustable
Address range of the speed dome
1-255
Fan/ Heater
Working range >50 ºC or < -5 ºC
VI、Problem short table
Problems
Possible causes
remedies
No action, no picture,
no indicator on when
power is switched on.
Wrong connection of power cables
Correct
Power supply adaptor damaged
Replace
Fuse damaged
Replace
Bad power cable connection
Correct
Normal self-check
and image but out
of control
Address or Baud rate setup wrong
Set up again
Protocol setup wrong
Set up again
RS485 bus bad connection
Check RS485 bus connection
Abnormal self-check
image with motor
noise
Mechanical failure
Repair
Camera inclined
Reinstall
Power supply not enough
Replace, better to place the adaptor
nearby the speed dome
Unstable image
Bad connection of video cable
Correct
Power supply not enough
Replace
Fuzzy image
At Manual focus state
Operate the dome camera or
preview any preset positions
Vitreous cover dirty
Clean the vitreous cover
Some dome camera
out of control or
control delayed
Power supply not enough
Replace, better to place the adaptor
nearby the speed dome
Whether matching resistor is in the
dome camera at the farthest end
Install matching resistor in the dome
camera
The distance is too far, the attenuation of
485 signal is too much
Thicken the controlling cable
The driving power of the 485 converter
is not enough
Replace with converter with
separate power supply