JETWAY JBC501F697-Q170-B User manual

1
Quick Installation Guide
NO. G03-JC501QIG02-F
Rev
：
1.1
Release date: 2021/1/15

2
Notice:
The photos in this file are for illustration purpose only. The model may not be the latest version. Please
refer to the product you purchased for actual specification.
1. To Open the Chassis
1. Locate the screws in the spots marked on the
top cover of the system and unscrew them
one by one.
2. Turn over the barebone system with the
heatsink upwards, as the photo shows.
3. Remove the screws in the marked positions
on the front panel.
4. Remove the screws in the marked positions
on the rear panel.

3
5. Lift the cover up to open the chassis.
Notice: For user to have a clear view of layout, we may unplug some of the cables during installation. In
this case, make sure that the cables are plugged into their original places when necessary installation
finished for the system to function normally.
2. To Install CPU

4
1. Find CPU socket on the board. Please make
sure that CPU socket is facing towards you
and the level is on you right hand side.
2. Remove the plastic protective plastic cover
from the socket. (Put it to the original place if
CPU is not installed. Do not touch the metal
contact point of the CPU socket).
3. Press down the level and move it towards the
right side to free it from the hook.
4. Open the level upwards about 135 degree
and the metal protection plate will be pulled
up at the same time.
5. Make sure that Pin-1 Golden Finger Indicator in the right place as shown in the
above photo and match the two alignment keys on the CPU with two points of the
socket. CPU can only be correctly installed with this direction. Incorrect installation
might cause damage to CPU.
Golden Finger
Indicator
Alignment Key
Alignment Key

5
6. Put down the load plate in the direction shown
above.
7. Press down the load level and move it
leftwards to make sure it is locked under the
notch.
Notice ：Please remove the screws that lock the board to the chassis cover when CPU installation
completed to install CPU heatsink upon CPU. The cables unplug during this process should be plugged to
their original places after heatsink installation.
3. To Install CPU Heatsink upon CPU
1. Find the above CPU heatsink and CPU thermal conductive gel package. Remove the
protective films on the both sides of the gel and apply the gel upon the bottom side of the
heatsink.

6
2. Apply corresponding thermal conductive gels to the bottom side of the heat sinks as the photo
show, and then place the CPU, PWM IC and South Bridge heatsink upon the board. The screw
holes of the heatsink should match corresponding screw holes of the board.
3. Tighten up the screws to lock the heat sinks to the board, and then apply corresponding
thermal conductive gels to the top side of the heat sinks as the photo shows. When installation
finished, tear off the protective film from the gels before assembling the back cover to the
chassis.
Notice: There should be one more HCS310HS1-F/ HCS501HS1-F/ HCS501HS2-F/ HCS3XXHS2-F left as
spare parts after normal assembly. User can use them to replace corresponding damaged thermal
conductive gels.
1: CPU Thermal conductive gel
(P/N: HCS3XXHS2-F*1 pcs), 20*20*0.5mm
2: PWM IC Thermal conductive gel
(P/N: HCS501HS1-F*1 pcs), 15* 47*1 mm
3: South Bridge Thermal conductive gel
(P/N: HCS501HS2-F *1 pcs), 25*25*1 mm
1: CPU Thermal conductive gel
(P/N: HCS310HS1-F*1pcs), 60*52*1.0mm
2: PWM IC Thermal conductive gel
(P/N: HCS501HS1-F*1pcs), 15* 47*1 mm
3: South Bridge Thermal conductive gel
(P/N: HCS501HS2-F*1pcs), 25*25*1 mm

7
4. To Install SO-DIMM to the board
1. Find the SO-DIMM slot on the board and
open the two eject tabs for further
installation.
2. Insert the gold-figure side of the compatible
SO-DIMM into the slot. The eject tabs will
lock automatically if installed correctly.
5. To Install MSATA Card
1. Locate the full-size Mini PCIe slot on the
board.
2. Remove the marked screw and use it to
lock Mini PCIe card to the slot in later
installation.

8
3. Insert the gold-figure side of the compatible
Mini PCIe card into the slot at a 30 degree.
4. Lock the card to the board by tightening up
the screw to the marked spot.
6. To Install WI-FI Card
1. Locate the half-size WIFI slot on the
board.
2. Remove the marked screw and use it to
lock WIFI card to the slot in later
installation.

9
3. Insert the gold-figure side of the
compatible WI-FI card into the slot at a
30 degree angle and press down.
4. Lock the card to the board by tightening
up the screw to the marked position.
5. Locate the reserved Wi-Fi antenna holes on the front panel. Remove the semi-broken
shield from the panel to install the antenna, as the following details show.

10
a) Back-side View: Put the metal ring into the antenna head at first, and then push this
antenna head into antenna hole of the rear panel.
b) Front-side View: Put the other metal ring into the antenna head, and then lock the
antenna head to the front side of the rear panel with the with hexagonal bolt.

11
6. Press the metal hat on the end of the
antenna string to the antenna slot on the
card as shown (If you install two
antenna, refer to above steps to finish
installation, and press the left metal hat
of the left antenna to the left slot, the
right metal hat to the right slot).
7. Connect the external Wi-Fi receiver
antenna to the antenna connector on the
rear panel.
7. To Install Hard Disk
1. Remove the HDD racks from the cover
by tightening up the screws in the
marked places.
2. Adjust the HDD and the racks in the
directions as the above photo shows.

12
3. Lock the SATA hard disk to one of the
racks by tightening the screws in the
marked position.
4. Lock the SATA hard disk to the other
rack by tightening the screws in the
marked position.
5. Find the compatible SATA cable for the
system in the accessories package.
To connect SATA
hard disk driver.
To connect onboard SATA power connector.
To connect onboard
SATA port.

13
6. Plug this side of the cable to SATA
power-in connector and SATA connector
of the hard disk.
7. Lock the racks hard disk with SATA HDD
installed to its original places by
tightening the screws in the marked
position.
8. Plug the other side cable to the SATA power connector and SATA port connector on the
board.

14
Notice:
When all necessary installations are finished, please make sure that all cables unplugged before
installations are connected to their original places before restoring the back cover to the chassis and
screws on the front panel/back panel/top cover locked to its original places (Refer to Part I). See to it that
the cables inside are not blocked or pressed.
8. To Wall Mount the System
1. Install wall mount rack to the system by tightening two screws in the marked position. Then lock the
other three screws on the other side in the same way.

15
2. Wall mount the system by tightening two screws in the marked positions. Then tighten up the other
two screws in the marked positions on the other rack.