JETWAY 920BFR3A User manual

920BF/920BN
USER'S MANUAL
3D-AGP VGA / 3D-Audio M/B
FOR Pentium

II / III
The author assumes no responsibility for any errors or omissions which may
appearin this documentnor does itmakea commitment to update the information
contained herein.
NO. G03-920BFR3A
Release date: DEC 2000
** Year 2000 compliant **
Trademark:
* Pentium is registered trademark and MMX is a trademark of Intel corporation, the other names and brands
are the property of their respective owners.
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

i
Chapter 1
1-1 Preface ...................................................................................................1
1-2 Key Feature ............................................................................................1
Chapter 2
Hardware Installation..................................................................................3
2-1 Unpacking...............................................................................................3
2-2 Motherboard Diagram.............................................................................4
2-3 Quick Reference for Jumpers, Connectors & Expansion Socket.............5
2-4 Installation Steps ....................................................................................6
2-5 Jumper Settings......................................................................................6
2-6 System Memory (DRAM)........................................................................8
2-7 Central Processing Unit (CPU) ...............................................................8
2-8 Expansion Cards.....................................................................................11
2-9 External Connectors ...............................................................................12
Chapter 3
AWARD BIOS SETUP..................................................................................18
3-1 STANDARD CMOS SETUP ...................................................................18
3-2 BIOS FEATURES SETUP......................................................................19
3-3 CHIPSET FEATURES SETUP...............................................................22
3-4 POWER MANAGEMENT SETUP ..........................................................23
3-5 PnP/PCI CONFIGURATION SETUP ......................................................25
3-6 LOADING BIOS DEFAULTS ...................................................................26
3-7 LOADING SETUP DEFAULTS................................................................26
3-8 INTEGRATED PERIPHERALS SETUP...................................................27
3-9 SUPERVISOR/USER PASSWORD ........................................................28
3-10 IDE HDD AUTO DETECTION ...............................................................28
3-11 SAVE & EXIT SETUP............................................................................29
3-12 EXIT WITHOUT SAVING ......................................................................29
Chapter 4
4-1 PC HEALTH MONITOR-II SOFTWARE ....................................................30
4-2 Sound Card Driver Quick Installation..........................................................30
APPENDIX-A Magic Install
TABLE OF CONTENT

1
Chapter 1
1-1 Preface
Thank you for purchasing this multifunction motherboard. It has the most flexibility you can
find in today’s computer market. This board integrates both Intel Pentium®II /Pentium®III &
Celeron™(Slot 1) / Coppermine processor and Celeron™ (Socket 370) PPGA / FCPGA
processor interface into a compact PC/AT compatible system along with share memory type
3D AGP VGA on-board, 3D PCI Audio on-board to support 4 channels speaker(If on-board
embedded Audio chip only), Ultra DMA 66, ACPI/AMP power management, and many other
powerful functions.
1-2 Key Feature
This motherboard is design for the PC user who wants highest possible quality and value in a
small package. It includes following main features:
•Supports both Slot 1 & Socket 370 CPU interface (onlyfor one CPU interface at a time).
•Supports Jumpless solution for setting of Front Side Bus Frequency (CPU Host
Clock),and CPU ratio in BIOS SETUP “CHIPSET FEATURES SETUP“.
•Multi-Speed Support : Provides 66/75/83/95/100MHz Front Side Bus Frequency to
support Intel PentiumII / PentiumIII / Coppermine / Celeron processor processor for
slot1 interface or Intel Celeron PPGA / FCPGA or a ZIP Socket 370 interface.
•Built-In High performance 3D AGP VGA:
∗Support share memory 2MB to 8MB selectable in BIOS SETUP.
∗Integrated programmable 24-bit true-color RAMDAC up to 230MHz pixel clock.
∗Integrated two 96x64 video line buffers for MPEG video playback.
∗Support 64 bit memory data bus interface; Support DIC, Direct Draw Driver.
∗Integrated a high performance and high quality 3D engine.
∗Support AGP Spec.1.0 compliant, 1xmode(66MHz), 2xmode(133MHz)
The VGA Share Memory Size can be 2MB/4MB/8MB selectable in the
“INTEGRATED PERIPHERALS Setup “ under BIOS Setup.
•Built in high quality PCI-Based HRTF 3D Extension Positional Audio Chip (Option for
motherboard that embedded Audio chip):
∗Supports rear side speakers, C3DX positional audio in 4 channels speaker mode.
∗Professional digital audio interface to support 24-bit SPDIF IN and OUT (44.1K and
48K format).
∗HRTF-base 3D positional audio, supporting DirectSound™ 3D and Aural A3D™
interface.
∗Digital functions that capable to provide hi-fi stereo, Dolby, 3D surround effects, and
playing MP3 music.
•You can add our Optical Kit (Option for motherboard that embedded Audio chip) to
connect any optical Input/Output device for super high quality sound transaction,
such as playing & recording MD(Mini Disk)/CD; CD-ROM directly recording to MD;

2
combine with DVD player to create a home theater system (This upgrade kit includes
Optical Module, Optical Cable, and Software DVD Driver).
•Chipset: SiS 620/5595 AGPset chip with I/O subsystems; CMI 8738 3D PCI Audio chip
(Option for motherboard that embedded Audio chip).
•DRAM Memory Support: supports 2 168-pin DIMMS(3.3V)from a memory size befween
16MB to 1.0GB.
•ISA and PCI expansion Slots: Three PCI slots ,Privodes one 16-bit ISA slot.
•Super Multi-I/O: Provides two high-Speed UART compatible serial ports and one parallel
port with EPP and ECP capabilities. Two floppy drives of either 5.25” or 3.5” (1.44MB or
2.88MB) are also supported without an external card.
•PCI Bus Master IDE Controller and ULTRA DMA 33/66: On-board PCI Bus Master IDE
controller with two connectors that supports four IDE devices in two channels, provides
faster data transfer rates, and supports Enhanced IDE devices such as Tape Backup, CD-
ROM drives and LS-120. This controller also supports PIO Modes 3 and 4 and Bus Master
IDE DMA 33/66Mbyte/Second.
•ACPI supporting for OS Directed Power Management
Keyboard Power On: When use ATX power supply and JP1 1-2 closed,choose power on
function by password in BIOS , can control power supply on by keyboard instead of power
button .
Ring-in Wake up: When Ring-In the system can wake up from SMI Mode.
Ring-in Power On: When Ring-In the system can power on automatic by this function by
use of ATX power supply.
RTC Power On: When use of ATX power supply and Enabled RTC Power On function, you
can setting RTC alarm to power on the system at the time length you setting .
Power Button: Press the button will place the system power on/off when use ATX power
supply .
Software off when use ATX power supply.
•Power Support: Efficient PWM switching power instead of traditional Linear Voltage
Regulator to prevent power component from being burned-out.
•Meets PC99 Requirements.
•Optional IRDA and PS/2 Mouse Connector: This motherboard supports an dedicated
16C550 standard UART,supporting infrared communication module for wireless interface
and PS/2 mouse cable set.
•Optional USB DEVICE Connector: This motherboard supports two USB port connectors for
USB devices.
•DMI Function Supporting.
•PC Health Monitoring : Allows you track PC’s CPU temperature, system voltage and fan
speed. When current temperature over warning temperature, the system will warning you
by alarm.
•Baby AT Form Factor: Dimensions 22cm x 25cm.
Chapter 2

3
Hardware Installation
2-1 Unpacking
This mainboard package should contain the following:
•The mainboard
•USER’S MANUAL for mainboard
•Cable set for Ultra DMA 33 IDE x1, Floppy x1, COM1 & COM2 x1, LPT x1, VGA x1,
Audio and Game x1(For motherboard that embedded Audio chip)
•CD for Drivers PACK
The mainboard contains sensitive electronic components which can be easily damaged by
electron-static, so the mainboard should be left in its original packing until it is installed.
Unpacking and installation should be done on a grounded anti-static mat.
The operator should be wearing an anti static wristband, grounded at the same point as the
anti-static mat.
Inspect the mainboard carton for obvious damage. Shipping and handling may cause
damage to your board. Be sure there are no shipping and handling damages on the board
before proceeding.
After opening the mainboard carton, extract the system board and place it only on a grounded
anti-static surface component side up. Again inspect the board for damage.
Press down on all of the socket IC’s to make sure that they are properly inserted. Do this only
on with the board placed on a firm flat surface.
Warning: Do not apply power to the board if it has been damaged.
You are now ready to install your mainboard. The mounting hole pattern on the mainboard
matches the Baby AT system board.
It is assumed that the chassis is designed for a Baby AT main board mounting. Place the
chassis on the anti-static mat and remove the cover.
Take the plastic clips, Nylon stand-off and screws for mounting the system board, and keep
them separate.
2-2 Motherboard Diagram

4
CPUFAN
SLOT-1
DIMM1
DIMM1
DIMM2
DIMM2
FLOPPY
IDE1
IDE2
SIS
5595 SIS
620
SLOT1
ISA1
BT1
BATT
CPU
U5
PGA 370
PCI1 PCI2 PCI3
IR
ATKB
PW2
PW1
COM1COM2
LPT1
VGA
GAME
AUDIO
U2
U3
SPDIFOUT
J5
MS PIN1
JP1
JP8
WOL
SYSFAN
JP7
JP5
JP6
JP3
JP4
USB
SPEK RST TBLED
KEYLOCK TBSW
HDLED
SMI
PS/ON
U13
BIOS U14-7
JP9
SPKIN1
SPDIFIN
Figure 2-1
2-3 Quick Reference for Jumpers, Connectors & Expansion Socket
Jumpers
Jumper Name Description Page
O
p
tional connector for motherboard that embedded wit Audio Chi
p

5
U14-7 CPU Bus Frequency Selection Open:100MHZ(off), Closed:66MHz(on) p.6
JP8 CMOS RAM Clear 1-2 Clear CMOS, 2-3 Normal p.7
J5 On board VGA Enabled/Disabled open : Enabled,closed : Disabled p.7
JP1 Keyboard power on function 1-2 : Enabled , 2-3 : Disabled p.7
JP9 VIO Voltage Selection 1-2 : 3.45V , 2-3 : 3.52V p.7
Connectors
Connector Name Description Page
PW1 AT Power Connector 12-Pin Block p. 12
PW2 ATX Power Connector 20-Pin Block p. 12
ATKB Keyboard Connector 5-Pin Female p.12
MS_PIN1 PS/2 Mouse Connector 5-Pin Block p.12
LPT1 Parallel Port Connector 26-Pin Block p.13
COM1,COM2 Serial Port COMA & COMB 10-Pin Block p.13
FDD Floppy Driver Connector 34-Pin Block p.13
IDE1 Primary IDE Connector 40-Pin Block p.14
IDE2 Secondary IDE Connector 40-Pin Block p.14
HDLED IDE activity LED 2-Pin Connector p.14
FPC Front Panel Connector 16-Pin Block p.14
IR Infrared Module Connector 5-Pin Block p.15
USB USB Port Connector 10-Pin Block p.15
CPUFAN,SYSFAN FAN Connector Fanning system connectors p.15
PS-ON ATX power button/soft power button 2-Pin Connector p.15
VGA VGA Connector 16-Pin Block p.16
WOL Wake On Lan 3-pin Block p.16
Jumpers & Connectors (Option for motherboard that embedded Audio Chip)
Item number Name Description Page
JP6 Audio Chip Enabled/Disabled 1-2 Enabled, 2-3 Disabled p.7
Audio Line IN / Line OUT / MIC 10-pin Connector p.16
Game Game port Connector 16-pin Connector p.16
JP3 CD-Audio IN 4-pin Block p.17
JP4 CD-Audio IN 4-pin Block p.17
JP5 AUX IN 4-pin Block p.17
SPDIFIN SPDIN(Sony/Philips Digital Interface) IN 4-pin Block p.17
SPDIFOUT SPDIN(Sony/Philips Digital Interface) OUT 4-pin Block p.17
JP7 For Optional Optical Kit Connector 10-pin Block p.17
Expansion Sockets
Socket/Slot Name Description Page
Slot1 CPU Slot
PentiumII/III/Coppermine CPU Slot p.8
Zip Socket 370 CPU Socket Celeron PPGA / FCPGA CPU Socket p.9
DIMM1,DIMM2 DIMM Module Socket 168-Pins DIMM SDRAM Module Expansion Socket p.9
PCI1, PCI2, PCI3 PCI Slot 32-bits PCI Local Bus Expansion slots p.11
ISA1 ISA Slot 16-bits ISA Bus Expansion slot p.11
2-4 Installation Steps
Before using your computer, you must follow the steps as follows:
1. Set Jumpers on the Motherboard

6
2. Install the CPU
3. Install DRAM Modules
4. Install Expansion card
5. Connect Cables, Wires, and Power Supply
2-5 Jumper Settings
1. CPU Bus Frequency Selection : U14-7
※You can also set the CPU Bus frequency and CPU ratio from the “CHIPSET FEATURES
SETUP” under BIOS SETUP.
Table for the Pentium III and Celeron Socket 370 CPU
Celeron Pentium III
Speed Bus Ratio Speed Bus Ratio
300/66 66MHz 4.5x 500E/100 100MHz 5.0x
333/66 66MHz 5.0x 550E/100 100MHz 5.5x
366/66 66MHz 5.5x 600E/100 100MHz 6.0x
400/66 66MHz 6.0x 650E/100 100MHz 6.5x
466/66 66MHz 7.0x 700/100 100MHz 7.0x
500/66 66MHz 7.5x 750/100 100MHz 7.5x
533/66 66MHz 8.0x 800/100 100MHz 8.0x
533A/66 66MHz 8.0x 850/100 100MHz 8.5x
566/66 66MHz 8.5x
600/66 66MHz 9.0x
633/66 66MHz 9.5x
667/66 66MHz 10.0x
700/66 66MHz 10.5x
733/66 66MHz 11.0x
766/66 66MHz 11.5x
∗Because the Ratio are fixed by CPU Manufacture, users don’t need
to setting ratio any more, this table just for reference use.
2. CMOS RAM Clear: JP8 (Yellow color selector)
WARNING: Make sure your computer is POWER OFF when you CLEAR CMOS.
Connect a jumper Cap over this jumper for a few seconds, will clears information stored in
the CMOS RAM Chip that input by user, such as hard disk information and passwords.
After CLEAR CMOS, you must enter the BIOS setup (by holding down <DEL> during
power-up) to re-enter BIOS information (see BIOS SETUP).
Selections JP8
Normal 2-3 (Default)
Clear CMOS 1-2 (momentarily)
U14-7
100MHz : Open
66MHz : Closed

7
Normal
CMOS RAM (Normal / Clear CMOS Data)
JP8
1
2
3
Clear CMOS
JP8
1
2
3
3. On Board Audio Chip Enabled / Disabled connector: JP6
JP
6
Closed (Default) : Enabled
Open : Disabled
1
4. On board VGA function Enabled / Disabled connector: J5
J5
1
Closed : Disabled
Open (Default) : Enabled
5. Keyboard Power on function: JP1
This function only support when use ATX power supply . When choose 1-2 closed
and use ATX power supply , you can choice power on system by power button or
keyboard in “KB Power ON Password” item under “Power Management Setup”.
JP1
1
1-2 closed : Enabled(Default)
JP1
1
2-3 closed : Disabled
6. VIO Voltage Setting Connector : JP9
The VIO Voltage Jumper Allow you to Select the Voltage Suppied to the DRAM , Chipset
and the CPU’S I/O buffer.
1
1-2 closed : 3.45V (Default)
JP9
1
2-3 closed : 3.52V
2-6 System Memory (DRAM)

8
This main board supports two 168-pins DIMM modules, the Max Memory Size is 1.0GB
Because of the VGA share memory function, the system must always occupy BANK0
(DIMM1)to booting the system.
DIMM 1 DIMM 2 System can be
Accept or Not
168-pin DIMM ×Accept
168-pin DIMM 168-pin DIMM Accept
×168-pin DIMM Not Accept
××Not Accept
∗Because of share memory function, the system must always occupy DIMM1 first to boot
up the system .
2-7 Central Processing Unit (CPU)
2-7-1 The motherboard provides a Slot-1 for Pentium II/III processor. The CPU on board
must have a fan or heat sink attached to prevent overheating.
WARNING: Without a fan or heat sink, the CPU will overheat and cause damage to both the CPU
and the motherboard.
To install a CPU, first turn off your system and remove its cover. Locate the Slot- 1 and place
RETENTION MODULE as following:
IMPORTANT: You must set jumper U14-7 for “Bus Frequency Selection” on page 6 depending on
the CPU that you install.
1. Attach heat sink to the CPU.
2. Place Part A on slot-1 and gently screw four corners on top of the mother- board.
PART A
2-7-2 The mainboard also provides a 370-pin ZIF Socket 370. The CPU on mainboard must
have a fan attached to prevent overheating.
To install a CPU, first turn off your system and remove its cover. Locate the ZIF Socket and
open it by first pulling the lever sideways away from the socket then upwards to a 90-degree
right angle. Insert the CPU with the white dot as your guide. The white dot should point
towards the end of the level. The CPU has a corner pin for three of the four corners, the CPU
will only fit in the one orientation as shown as follow. With the added weight of the CPU fan,
no force is required to insert the CPU. Once completely inserted, hold down on the fan and
close the Socket’s lever.
IMPORTANT: You can setting the CPU ratio and Host Frequency under “Chipset Features Setup”.

9
CPU ZIF Socket 370
Lock
Socket 370
Blank
Lever
White Dot
Socket 370
CPU
2-7-3 Intel®Pentium®III Processor (256K) in the FC-PGA form factor: Mechanical Features
The FC-PGA package has the processor’s silicon die directly mounted to a pinned interposer substrate.
The pin grid array is partially populated and there may be surface mount components in the unpopulated
central area of the pin field.
Intel®Pentium®III Processor in the FC-PGA form factor: Mechanical Features
Reference Design: Heatsink
Substrate
Flip Chip Die
Pins
Fillet Epoxy
(Not to scale)
Flip-Chip Si Core
C4 Solder bumps
Surface mounted pins
Fillet Epoxy
(Not to scale)
Multi-layer substrate
FC-PGA with the reference
design heatsink
zIntel’s reference design thermal solution is an
active heatsink; an extruded aluminum heatsink
base and a fan attached to the top on the fin
array.
• Heatsinks for the PPGA will not work with the
FC-PGA. A pedestal is required on the
underside of the heatsink to clear the socket
cam box
zRecommended thermal interface
material: Chomerics* XTS454.

10
Heatsink Attachment
FC-PGA with a PPGA heatsink
CPU Insertion
Step 1
Open the socket by raising the actuation lever.
Step 1
Remove the protective liner from the thermal interface
material on the underside of the heatsink.
This liner is not normally present on the Intel reference
active heatsink.
Step 2
Orient the heatsink with the keyed edge of
heatsink along the cam box side of the
processor.
The clip should be oriented so that the thumb tab will
engage on the cam box side of the socket.
Step 2
Insert the processor.
Ensure proper pin 1 orientation by aligning the
FC-PGA corner marking with the socket corner
closest to the actuation arm tip. The pin field is
keyed to prevent mis-oriented insertion.
Don’t force processor into socket. If it does not go in
easily, check for mis-orientation and debris.
Make sure the processor is fully inserted into the
socket on all sides.
Step 3
Close the socket by lowering and locking the
actuation lever.
Step 3
Seat the heatsink onto the processor and engage
the clip opposite from the cam box onto its socket
tab first.
CAUTION: Do not slide the heatsink once it is
attached to the processor as the thermal interface

11
2-8 Expansion Cards
You must read the documentation come with expansion card for any hardware or software
settings that may be required to setup your specific card.
Installation Procedure:
1. Read the documentation from your expansion card.
2. Set any necessary jumpers on your expansion card.
3. Remove your computer’s cover.
4. Remove the bracket on the slot you intend to use.
5. Carefully align the card’s connectors and press firmly.
6. Secure the card on the slot with the screw you remove in step 4.
7. Replace the computer’s cover.
8. Setup the BIOS if necessary.
9. Install the necessary software drivers for your expansion card.
Assigning IRQs for Expansion Cards
Some expansion cards may require an IRQ to operate. Generally an IRQ must be
exclusively assigned to only one device. In an standard design there are 16 IRQs available
but most of them are occupied by the system and leaves 6 free for expansion cards.
With moset recent device, the BIOS automatically assign an IRQ number to PCI expansion
cards. Please make sure there are no any of two devices use same IRQ, otherwise your
computer may experience some problem when those two devices are in use at the same time.
Assigning DMA Channels for ISA Cards
Some devices may also need a DMA (Direct Memory Access) channel. Its assignments for
this motherboard are handled same way as the IRQ assignment process described above.
The DMA channel is selectable in the PCI and PNP configuration section under BIOS Setup
utility.
2-9 External Connectors

12
1. Power connector: AT Power Connector (12-pin block): PW1
This connector connects to a standard AT power supply. To connect the leads from the
power supply, ensure first that the power supply is not plugged. Most power supplies
provide two plugs (P8 and P9), each containing six wires, two of which are black. Orient
the connectors so that the black wires are located in the middle.
Using a slight angle, align the plastic guide pins on the lead to their receptacles on the
connector. Once aligned, press the lead onto the connector until the lead locks into place.
Power Plugs from Power Supply
Power Connector on Motherboard
PG+12V
GND
+5V-12V-5V
+5V
P8P9
ORG
RED
YLW
BLU
BLK
BLK
BLK
BLK
WHT
RED
RED
RED
2. Power Connector: ATX Power Connector (20-pin block): PW2
ATX Power Supply connector. This is a new defined 20-pins connector that usually
comes with ATX case. The ATX Power Supply allows to use soft power on momentary
switch that connect from the front panel switch to 2-pins Power On jumper pole on the
motherboard. When the power switch on the back of the ATX power supply turned on,
the full power will not come into the system board until the front panel switch is
momentarily pressed. Press this switch again will turn off the power to the system board.
PIN ROW2 ROW1
1 3.3V 3.3V
2 -12V 3.3V
3 GND GND
4 Soft Power On 5V
5 GND GND
6 GND 5V
Pin 1
3. Keyboard Connector (5-pin female): ATKB
This connection is for a standard IBM-compatible keyboard. May also be known as a 101
enhanced keyboard.
Keyboard Connector (5-pins female)
Connector Plug from Keyboard
4. PS/2 Mouse Connector (5-pin block): MS_PIN1
If you are using a PS/2 mouse, you must purchase an optional PS/2 mouse set which
connects to the 5-pins block and mounts to an open slot on your computer‘s case.
* Please don’t turn off / on power supply too
quickly. We recommend at least wait 4 sec
before turn on the power to protect the system.

13
1: DATA
2: NC
3: GND
4: VCC
5: CLK
PIN 1
PS/2 Mouse Module Connector
5. Parallel Printer Connector (26-pin Block): LPT1
Connection for the enclosed parallel port ribbon cable with mounting bracket. Connect the
ribbon cable to this connection and mount the bracket to the case on an open slot. It will
then be available for a parallel printer cable.
NOTE: Serial printers must be connected to the serial port. You can enable the parallel port and choose the
IRQ through BIOS Setup.
Pin 1
Parallel Printer Connector
LPT
6. Serial port COMA and COMB Connector (Two 10-pin blocks): COM1, COM2
These connectors support the provided serial port ribbon cables with mounting bracket.
Connect the ribbon cables to these connectors and mount the bracket to the case on an
open slot. The two serial ports on the mounting bracket will then be used for pointing
devices or other serial devices. See BIOS configuration of “Onboard Serial Port”
COM 1
Pin 1
Pin 1
COM 2
Serial
p
ort COMA and COMB Connector
7. Floppy drive Connector (34-pin block): FDD
This connector supports the provided floppy drive ribbon cable. After connecting the single
plug end to motherboard, connect the two plugs at other end to the floppy drives.
Pin 1
Flo
ppy
Drive Connector
FD
D
8. Primary IDE Connector (40-pin block): IDE1

14
This connector supports the provided IDE hard disk ribbon cable. After connecting the
single plug end to motherboard, connect the two plugs at other end to your hard disk(s). If
you install two hard disks, you must configure the second drive to Slave mode by setting
its jumpers accordingly. Please refer to the documentation of your hard disk for the jumper
settings.
Primary IDE Connector
Pin 1
9. Secondary IDE Connector (40-pin block): IDE2
This connector connects to the next set of Master and Slave hard disks. Follow the same
procedure described for the primary IDE connector. You may also configure two hard
disks to be both Masters using one ribbon cable on the primary IDE connector and
another ribbon cable on the secondary IDE connector.
Secondary IDE Connector
Pin 1
10. IDE activity LED: HDLED
This connector connects to the hard disk activity indicator light on the case.
HDLED
IDE (Hard Drive) LED
+-
11. Front Panel Connector: This 16-pin connector to connect to case front panel switch.
A. Turbo LED switch: TBLED
The motherboard‘s turbo function is always on. The turbo LED will remain constantly lit
while the system power is on. You may also to connect the Power LED from the
system case to this lead. See the figure below.
B. Reset switch lead: RST
This 2-pin connector connects to the case-mounted reset switch for rebooting your
computer without having to turn off your power switch. This is a preferred method of
rebooting in order to prolong the life of the system‘s power supply. See the figure
below.
C. Keyboard lock switch lead & Power LED: KEYLOCK & PW
This 5-pin connector connects to the case-mounted key switch for locking the
keyboard for security purposes and Power LED together.

15
D. Speaker connector: SPEAKER
This 4-pin connector connects to the case-mounted speaker. See the figure below.
System Case Connections
GND
Turbo LED
Reset S
W
VCC
GND
Speaker
VCC
G
ND
NC
GND
NC
GND
VCC
GND
Power LED
TurboSW
Keyboard
Lock
12. IR infrared module connector: IR
This connector supports the optional wireless transmitting and receiving infrared module.
This module mounts to small opening on system cases that support this feature you must
also configure the setting through BIOS setup. Use the five pins as shown on the Back
View and connect a ribbon cable from the module to the motherboard according to the pin
definitions.
Infrared Module Connector
IR
N.C
IRR
X
GND
IRTX
VCC
1
2
3
4
5
13. USB Port connector: USB
USB
USB Port Connector
Pin 1
Vcc
V
c
c
+DATA
NC
-DATA
GND
-DATA
N
C
GND
+ DATA
14. FAN connector: CPUFAN , SYSFAN
CPUFAN
1
Fan Connector
1
SYSFAN
15. ATX Power button/ Soft Power button: PS-ON
When using ATX power, the system power can be controlled by a momentary switch
connected to PS-ON Pushing the button once will switch the system between ON and

16
SLEEP. Pushing the switch while in the ON mode more than 4 seconds will turn the
system off. The system Power LED shows the status of the system’s power.
Selections PS-ON
One touch Power ON/OFF 2-4
ATX Power button/Soft Power button
PS-ON
24
16. VGA connector: VGA
This connector supports the provided VGA cable with mounting bracket. Connect the
ribbon cable to connector and mount the bracket to the case on an open slot .
VGA Connector
1
V
G
A
2
15
16
Orient the red stripe on the
monitor cable with Pin 1
17. Wake On Lan connector: WOL
WOL
+ 5VSB
GND
W
ON
18. Audio connector: Audio
Audio Connector
A
UDIO
1
2
9
10
GND MICP
L – I N - R
GND
L – OUT - R
GND
MIC
L – OUT - L
L – I N - L
Orient the red stripe on the
monitor cable with Pin 1
Audio
Game
Jumpers & Connectors (Option for motherboard that embedded Audio Chip)

17
19. Game Port connector: GAME
GAME PORT Connector
GAME
1
2
15
16
Orient the red stripe on the
monitor cable with Pin 1
Audio
Game
20. CD-ROM Audio connector: JP3,JP4
CD-ROM Audio connector
JP3
1
2
3
4
JP4
1
2
3
4
21. PC Speaker signal Input connector: SPKIN 1
SPKIN1
22. SPDIF (Sony / Philips Digital Interface) Input / Output Connectors: SPDIFIN 1 /
SPDIFOUT
SPDIFOUT SPDIFIN 1
+5V
GND
SPDIFIN
SPDIFOUT
GND
23. Optical kit connector: JP7
JP
7
1

18
Chapter 3
AWARD BIOS SETUP
Award's ROM BIOS provides a built-in Setup program which allows user modify the basic
system configuration and hardware parameters. The modified data will be stored in a battery-
backed CMOS RAM so data will be retained even when the power is turned off. In general,
the information saved in the CMOS RAM stay unchanged unless here is configuration change
in the system, such as hard drive replacement or new equipment is installed.
It is possible that CMOS had a battery failure which cause data lose in CMOS_RAM. If so,
re_enter system configuration parameters become necessary.
To enter Setup Program
Power on the computer and press <Del> key immediately will bring you into BIOS CMOS
SETUP UTILITY.
ROM PCI/ISA BIOS (2A6INJ19)
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
BIOS FEATURES SETUP
CHIPSET FEATURES SETUP
POWER MANAGEMENT SETUP
PNP/PCI CONFIGURATION
LOAD BIOS DEFAULTS
LOAD SETUP DEFAULTS
INTEGRATED PERIPHERALS
PASSWORD SETTING
IDE HDD AUTO DETECTION
SAVE & EXIT SETUP
EXIT WITHOUT SAVING
Esc : QUIT ↑↓→← : Select Item
F10 : Save & Exit Setup (Shift) F2 : Change Color
Figure 3-1
The menu displays all the major selection items and allow user to select any one of shown
item. The selection is made by moving cursor (press any direction key) to the item and press
<Enter> key. An on_line help message is displayed at the bottom of the screen as cursor is
moving to various items which provides user better understanding of each function. When a
selection is made, the menu of selected item will appear so the user can modify associated
configuration parameters.
3-1 STANDARD CMOS SETUP
Choose "STANDARD CMOS SETUP" in the CMOS SETUP UTILITY Menu (Figure 3-1). The
STANDARD CMOS SETUP allows user to configure system setting such as current date and
time, type of hard disk drive installed in the system, floppy drive type, and the type of display
monitor. Memory size is auto-detected by the BIOS and displayed for your reference. When
a field is highlighted (direction keys to move cursor and <Enter> key to select), the entries in
the field will be changed by pressing <PgDn> or <PgUp> keys or user can enter new data
directly from the keyboard.