JETWAY HBJC501F797-Q37-B User manual

TECHNICAL MANUAL
Of
Intel Q370 Express Chipset
Based Mini-ITX M/B
NO. G03-NF797-F
Revision: 4.0
Release date: December 15, 2020
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

i
Environmental Protection Announcement
Do not dispose this electronic device into the trash while discarding. To minimize
pollution and ensure environment protection of mother earth, please recycle.

ii
ENVIRONMENTAL SAFETY INSTRUCTION............................................................................. iii
USER’S NOTICE...............................................................................................................................iv
MANUAL REVISION INFORMATION...........................................................................................iv
ITEM CHECKLIST............................................................................................................................ iv
CHAPTER 1 INTRODUCTION OF THE MOTHERBOARD
1-1 FEATURE OF MOTHERBOARD.........................................................................................1
1-2 SPECIFICATION.................................................................................................................... 2
1-3 LAYOUT DIAGRAM...............................................................................................................3
CHAPTER 2 HARDWARE INSTALLATION
2-1 JUMPER SETTING................................................................................................................ 8
2-2 CONNECTORS AND HEADERS........................................................................................ 12
2-2-1 CONNECTORS........................................................................................................12
2-2-2 HEADERS................................................................................................................ 16
CHAPTER 3 INTRODUCING BIOS
3-1 ENTERING SETUP................................................................................................................ 21
3-2 BIOS MENU SCREEN...........................................................................................................22
3-3 FUNCTION KEYS...................................................................................................................22
3-4 GETTING HELP......................................................................................................................23
3-5 MENU BARS........................................................................................................................... 23
3-6 MAIN MENU............................................................................................................................ 24
3-7 ADVANCED MENU................................................................................................................25
3-8 CHIPSET MENU..................................................................................................................... 39
3-9 SECURITY MENU.................................................................................................................. 42
3-10 BOOT MENU........................................................................................................................... 45
3-11 SAVE & EXIT MENU..............................................................................................................46
TABLE OF CONTENT

iii
Environmental Safety Instruction
Avoid the dusty, humidity and temperature extremes. Do not place the product in
any area where it may become wet.
0 to 40 centigrade is the suitable temperature. (The temperature comes from the
request of the chassis and thermal solution)
Generally speaking, dramatic changes in temperature may lead to contact
malfunction and crackles due to constant thermal expansion and contraction from
the welding spots’ that connect components and PCB. Computer should go
through an adaptive phase before it boots when it is moved from a cold
environment to a warmer one to avoid condensation phenomenon. These water
drops attached on PCB or the surface of the components can bring about
phenomena as minor as computer instability resulted from corrosion and oxidation
from components and PCB or as major as short circuit that can burn the
components. Suggest starting the computer until the temperature goes up.
The increasing temperature of the capacitor may decrease the life of computer.
Using the close case may decrease the life of other device because the higher
temperature in the inner of the case.
Attention to the heat sink when you over-clocking. The higher temperature may
decrease the life of the device and burned the capacitor.

iv
USER’S NOTICE
COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED
OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN
PERMISSION OF THE MANUFACTURER.
THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE THIS MOTHER-BOARD SERIES AND WE
DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME
WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY
KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA,
INTERRUPTION OF BUSINESS AND THE LIKE).
PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE
REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE
USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S BENEFIT, WITHOUT
INTENT TO INFRINGE.
Manual Revision Information
Reversion Revision History Date
4.0 Fourth Edition December 15, 2020
Item Checklist
Motherboard
Cable(s)

1
Chapter 1
Introduction of the Motherboard
1-1 Feature of Motherboard
Intel®Q370 express chipset
Support LGA 1151 CPU socket for the 8th Intel®Coffee Lake processors (TDP ≤
65W, and the whole system power consumption under 120W).
Support 2* DDR4 2400MHz SO-DIMM up to 64GB and dual channel function
Integrated with 1* Intel i211AT & 1* i219-LM Gigabit Ethernet LAN chip
Support up to 6*USB 3.1 Gen.2 port & 4 * USB 2.0 port
Support up to 2*RS232 (RS422/485 optional) COM port
Support 2* SATAIII (6Gb/s) Devices with RAID 0/1 mode & 1* M.2 M-key,
type-2242/2260/2280 slot
Support 1* PCIE x4 side-way expansion slot; 1*M.2 E-key, type-2230 slot
1* HDMI port, 2* DP port & 1* EDP with support for 3 independent displays (HDMI
optional changeable with DP)
Support Smart FAN function
Supports ACPI S3 Function
Compliance with ErP Standard
Support Watchdog Timer Technology
Solution for Digital Signage, Industrial PCs, Factory Automation, Public Sector,
and Digital Security applications

2
1-2 Specification
Spec
Description
Design
Mini-ITX form factor; PCB size:17.0x17.0cm
Chipset
Intel Q370 Express Chipset
CPU Socket
Intel®LGA 1151 Socket for Coffee Lake series processors
* for detailed CPU support information please visit our website
Memory Slot
2*DDR4 SO-DIMM slot support DDR4 2400MHz non-ECC
SDRAM
Maximum capacity: up to 64GB
Support dual channel function
*Memory frequency range also depends on CPU support
Expansion Slot
1* PCIE x 4 slot for 1* PCIE x 4 or 4*PCIE x1 for dedicated
extension card (PCIEX4)
1 * M.2 E-key slot, type-2230 (M2E)
Storage
2* SATAIII 6G/s ports with support for RAID 0/1 mode
1* M.2 M-key slot, type-2242/2260/2280, PCIe x4 with SATA
interface (M2M)
Gigabit LAN
Chip
Integrated with 1* Intel i211AT Gigabit Ethernet LAN chip &
1* Intel i219-LM Gigabit PHY LAN chip
Support Fast Ethernet LAN function of providing
10/100/1000Mbps Ethernet data transfer rate
Audio Chip
Realtek ALC662-VD 6-channel Audio Codec integrated
Audio driver and utility included
BIOS
AMI Flash ROM
Multi I/O
Rear Panel I/O:
1* 9V~36V DC-in power jack
1* HDMI port
2* DP port
2* RS232/422/485 COM port
4* USB 3.1 (Gen.2) port

3
2* RJ-45 LAN port
1*3-phone audio jack (Line-in, Line-out, MIC)
Internal I/O Connectors & Headers:
1 *2-pin internal 9V~36V power connector
1*SATA power-out connector
1* CPUFAN connector & 1* SYSFAN connector
2* internal vertical USB 3.1 (Gen.2) ports
1* Front panel header
1 * PS2 Keyboard & Mouse header
1* SMBUS header
2* 9-Pin USB 2.0 headers for 4* USB 2.0 ports
1* Front panel audio header
1* LAN Status LED header
1* GPIO header
1* EDP header
1-3 Layout Diagram
Rear IO Diagram
Line-In
Line-Out
MIC
RJ-45 LAN Ports
USB3 .1 (Gen.2)
Ports
COM1
Serial Port
COM2
Serial Port
HDMI Port
DP Port
DP Port
9~36V DC-IN
Power Jack

4
Motherboard Internal Diagram:
*Rear IO
Connector
(Refer to Page-3)
LGA 1151
CPU Socket
DDR4
SODIMM Slots
(SODIMM1/SODIMM2)
SMBUS
Header
Intel Chipset
2*SATAIII Ports
PCIE X 4 Slot
Front Panel
Header
eDP Port
Header
LAN_LED
Header
Front Panel
Audio Header
USB 2.0
Port Header
USB 3.1 (Gen.2)
Port Header
GPIO Header
M.2 M-Key Slot
(M2M)
M.2 E-Key Slot
(M2E)
CPUFAN
Connector
PS2KBMS Header
SYSFAN2 Connector
SATA Power-out
Connector
Buzzer
Internal
DC 9V~36V
Power Connector

5
Motherboard Jumper Positions:
JP5
JP4
JP1
AT_COPEN
JBAT

6
Jumper
P/N
Name
Description
JBAT
Pin (1-2): Clear CMOS RAM Settings
Pin (3-4): Flash Descriptor Override
Pin (5-6): PWROK Override
6-pin Block
JP1
COM1 Port Pin9 Function Select
4-pin Block
JP4
LCD Backlight Select
4-pin Block
JP5
LCD Panel VCC Select
4-pin Block
AT_ COPEN
Pin (1-2): AT Mode Select
Pin (3-4): Case Open Display Select
4-pin Block
Connectors
P/N
Name
DC_IN
9V~36V DC-IN Power Jack
HDMI
HDMI Port Connector
DP12
Display Port Connector X2
COM12
Serial COM Port Connector X2
UL2/UL1
Top: RJ-45 LAN Connector X2
Middle & Bottom: USB 3.1 (Gen.2) Port Connector X4
AUDIO
Top: Line-in Connector
Middle: Line-out Connector
Bottom: MIC Connector
FP_USB30
/FP_USB31
Internal USB 3.1 (Gen.2) Port Connector X2
DC2P
2-pin Internal 9V~36V Power Connector
SATA1/2
SATAIII Port Connector
SATAPWR
SATA Power-out Connector
CPUFAN
CPU FAN Connector
SYSFAN
System FAN Connector

7
Headers
P/N
Name
Description
JW_FP
Front Panel Header(PWR LED/ HD
LED/Power Button /Reset)
9-pin Block
PS2KBMS
PS2 Keyboard & Mouse Header
6-pin Block
SMBUS
SMBUS Header
4-pin Block
FP_USB20
/FP_USB21
USB 2.0 Port Header
9-pin Block
FP_AUDIO
Front Panel Audio Header
9-pin Block
LAN_LED
LAN Activity LED Header
4-pin Block
GPIO
GPIO Port Header
10-pin Block
EDP
EDP Port Header
40-pin Block

8
Chapter 2
Hardware Installation
2-1 Jumper Setting
Pin 1&2 of JBAT (6-pin): Clear CMOS RAM Setting
1-2 Closed: Clear CMOS(One Touch).
1-2 Open: Normal(Default);
Pin 1&2 of JBAT → Clear CMOS
Pin1
2
Pin1
2
Pin 3&4 of JBAT (6-pin): Flash Descriptor Override Select
Pin1
2
Pin1
2
Pin 3&4 of JBAT →
Flash Descriptor Override
3-4 Open: Normal(Default);
3
4
3-4 Closed: Disable Flash
Descriptor Security (override).
3
4
JBAT
JBAT

9
Pin 5&6 of JBAT (6-pin): PWROK Override Select
Pin1
2
Pin1
2
5-6 Open: Normal(Default);
3
4
3
4
Pin 5&6 of JBAT → PWROK Override
5-6 Closed: PWROK Override.
6
5
5
6
* Note : PWROK override is for manufacturing test only.
JP1 (4-pin): COM1 Port Pin9 Function Select
JBAT
JP1

10
JP4 (3-pin): LCD Backlight Select
JP5 (4-pin): LCD Panel VCC Select
** Note : The maximum carried current is 1A.
JP4
JP5

11
Pin 1&2 of AT_COPEN (4-pin): ATX Mode/AT Mode Select
Pin 1&2 of AT_COPEN
→ ATX/AT Mode Select
1-2 Open: ATX Mode
Selected(Default);
;
1-2 Closed: AT Mode Selected.
.
Pin1
2
3
4
Pin1
2
4
3
*ATX Mode Selected: Press power button to power on after power input ready;
AT Mode Selected: Directly power on as power input ready.
Pin 3&4 of AT_COPEN (4-pin): Case Open Message Display Function Select
Pin 3&4 of AT_COPEN
→ Case Open Detection
CASE OPEN
2
GND
4
3
Pin1
Pin (3&4) Closed:When Case open function pin short to GND, the Case open
function was detected. When used, needs to enter BIOS and enable ‘Case Open
Detect’function. In this case if your case is removed, next time when you restart your
computer, a message will be displayed on screen to inform you of this.
AT_COPEN
AT_COPEN

12
2-2 Connectors and Headers
2-2-1 Connectors
Rear Panel Connectors
*Refer to Page-3 Rear IO Diagram
Icon
Name
Function
9V~36V DC-in
Power Jack
For user to connect compatible power adapter to provide
power supply for the system.
HDMI Port
To connect display device that support HDMI
specification.
Display Port
To the system to corresponding display device with
compatible DP cable.
Serial Port
Mainly for user to connect external MODEM or other
devices that supports Serial Communications Interface.
RJ-45 LAN Port
This connector is standard RJ-45 LAN jack for Network
connection.
USB 3.1 (Gen.2)
Port
To connect USB keyboard, mouse or other devices
compatible with USB 3.1 (Gen.2) specification. Ports
support up to 10Gbps data transfer rate.
Audio Connectors
Blue: Line-in Connector
Green: Line-out Connector
Pink : MIC Connector

13
(1) COM12: RS232/422/485 Ports
COM1/COM2 port can function as RS232/422/485 port. In normal settings
COM1/COM2 functions as RS232 port. With compatible COM cable COM1/COM2
can function as RS422 or RS 485 port. User also needs to go to BIOS to set
‘Transmission Mode Select’ for COM1/COM2 at first, before using specialized cable
to connect different pins of this port.
For RS422 Mode
RS422TX-(B)
RS422TX+(A)
RS422RX+(A)
RS422RX-(B)
(B)
For RS485 Mode
RS485 D-(B)
RS485 D+(A)
(2) DC2P (2-pin block):Internal 9V~36V Power Connector
Pin No.
Definition
1
+9V~36V
2
GND
Pin1
Warning: Find Pin-1 position before connecting power cable to this 2-pin power connector. WRONG
INSTALLATION DIRECTION WILL DAMAGE THE BOARD!!

14
(3) SATA1/2 (7-pin): SATAIII Port connector
These are high-speed SATAIII port that supports 6GB/s transfer rate.
Pin No.
Definition
1
GND
2
TXP
3
TXN
4
GND
5
RXN
6
RXP
7
GND
(4) SATAPWR (4-pin): SATA HDD Power-Out Connector
Pin1
+12V
GND
+5V
GND
Warning: Make sure that Pin-1 of compatible SATA Power connector is inserted into corresponding
Pin-1 of SATAPWR connector to avoid possible damage to the board and hard disk drive!
SATAPWR
SATA1
SATA2

15
(5) SYSFAN (4-pin): System Fan Connector
Fan Speed
GND
Pin1
+12V Fan Power
Control
(6) CPUFAN(4-pin): CPU Fan Connector
Fan Speed
GND
Pin1
+12V Fan Power
Control
SYSFAN
CPUFAN