Jiffy J-1 User manual

Jiffy® J-1/J-2/J-200 Model Steamer
FEATURES
• Cast aluminum housing for durability (Models J-1 and J-2)
• High impact polymer housing (Model J-200)
• Lightweight, flexible hose- Models J-2/J-200 (J-1 series
utilizes a
brass hat nozzle)
• Shatterproof water bottle
• Safety wiring feature temporarily turns the unit off if it
accidentally runs dry
• Comfortable, easy-to-grip handle
• Removes wrinkles up to five times faster than
conventional ironing
• Easy-roll casters for mobility (casters not included with
J-1 series)
• Numerous steam head attachments available
• 120 Volt or 230 Volt units available
• Backed by Jiffy®'s renowned customer service--should your
steamer need repair, sendit to us and we will repair andship
the unit within 24 hoursfrom its arrival to ourplant
INCLUDES:
Rod Set
(not included with
J-1 series)
Owner's
Manual Hat Nozzle
(J-1 Models)
Assembly~
Wrench
Water
Bottle
From the library of: Superior Sewing Machine & Supply LLC

Jiffy® J-1/J-2/J-200 Model Steamer Directions
1. For J-2/J-200 models, attach hose firmly with included
assembly wrench, which
is magnetized and located on
the bottom
of the unit (figure #1). Assemble and attach
hose hanger rod set. See page 9 for assembly instructions.
For
J-1 models, the brass hat nozzle should already be
attached. There is no rod set for J-1 models.
2. Invert bottle
of fresh tap or distilled water, plug into
proper voltage outlet,
turn switch to lighted ON position
and you will have steam within minutes. Never substitute the
Ji~ Figure 1
Steamer water bottle.
Figure 2
Figure 4
3. For easy operation, mount optional Ji~ Steamboard to
door
or wall to hold clothing while steaming (figure #2).
For hanging garments without optional Ji~
Steamboard, simply install an eye screw or nail to inside
of a doorway or directly onto a wall or you may use
steamer's rod set as shown
in figure 3. Touch material
lightly with steaming head and wrinkles will vanish
instantly. The combined touch
of the steaming head and
the direct steam is very important. Some articles can be
steamed better from the underneath side. Speed and
efficiency is accomplished with a little practice. Always
steam with hose
in an uprightposition, so any
condensation is free to flow back into steamer.
If
steaming in a low position near floor, extend hose up and
out frequently to keep clear
of
condensation. DO NOT ALLOW
STEAMER TO RUN DRY.
4. Hang steamhead in an upright
position in the hose hanger section
when not in use and turn switch to
OFF (figure #3).
5. Periodically, pour old water out
of
steamer to avoid sediment buildup and
maintain proper water level (figure Figure 3
#4). Remove hardwater deposits with JiffY ®Liquid
Cleaner. See page 28 for complete cleaning
instructions.
NOTE: No two water supplies have the same mineral content. If your steamer
begins to cut
on and off during normal use, the thermostat is indicating the
heating unit needs the sediment cleaned out.
From the library of: Superior Sewing Machine & Supply LLC

Jiffy® J-1/J-2/J-200 Parts Diagram
----- -\
/12 ·- 3- ·-·
· ~
/ @lli'j
'
' ..
I 13 I
. ~J I
',:~~~, t~.
·/
v
\. \
-- _\
g /\\\
.\
'
;
;
; 10
Should you ever need replacement parts for your J~ Steamer, you may
purchase them separately. Use this handy diagram andparts list to identify any
part you may need. Please include model and serial number when ordering.
Key#
1
2
Jiffy Steamer
Part#
1030
0031
0031A
0041
0035
Part Description
Rod Set and Nut Complete with Metal Studs
Hose Hanger Rod Set w ith Adapter Complete
Hose Hanger Rod Set w ithout Adapter Complete
Base Adapter w ith Thumb Scre w (for Old Style Rods Sets)
Hook Section of Rod Set
List
Price
$ 25.50
$ 25.50
$ 21.50
$ 4.00
$ 6.50
From the library of: Superior Sewing Machine & Supply LLC

Jiffy® J-1/J-2/J-200 Parts Diagram Key
3 0036 Middle Section of Rod Set
$
7.50
4 0037 Bottom Section of Rod Set
$
7.50
5 0043 Metal Threaded Cap Screw for Rod Set
$
1.50
6 0039 Metal Threaded Stud for Rod Sections
$
150
7 1031 1/2 " Split Ring for Rod Set
$
0.50
8 1032 Rod Set Nut
$
6.00
9 0253 Plastic Steam Head/Handle Replacement Kit $ 22.00
10 0251 Plastic Head/Handle Hose Attachment Complete $ 50.00
0280 Hose Per Foot (Black in Color)
$
3.00
11 0002 Painted Die Cast Aluminum Housing $ 51.50
0023
Plastic Water Bottle " A" with Cap
$
6.50
0027 Replacement Cap for Water Bottle "A " $ 0.75
12 0026A
Plastic Water Bottle " B" without Check Valve Cap
$
5.75
13 0025
Plastic Water Bottle " B" w ith Check Valve Cap
$
9.50
14 0027A Replacement Check Valve Cap for Water Bottle " B"
$
3.75
15 0004 Round Beauty Ring
$
0.75
0122 Toggle Sw itch (3 Pieces)
$
7.50
0127 Red Neon Pilot Light w ith Lock Ring 120 Volt
$
4.00
0128 Red Neon Pilot Light w ith Lock Ring 230 Volt
$
4.00
16 1125 Green Lighted Contura Rocker Sw itch 120 Volt
$
9.00
1126 Green Lighted Contura Rocker Sw itch 230 Volt
$
9.00
17 0132 Cord Set (16 /3 gauge) w ith Strain Relief
$
9.50
18 0146B Cord Strain Relief
$
1.50
19 0028 Water Cup w ith 90 Degree Brass Fitting $ 18.00
0147 Internal Wire Set for Models w ith Front Red Light
$
9.00
20 0148 Internal Wire Set for Models w ith Green Contura Rocker Sw itch
$
9.00
0596 Heating Unit Kit (w iring included) for Models w ith Front Red Light
- 120 Volt Cord Set and 4" Water Line
$ 81.50
0177A Heating Unit Kit (w iring included) for Models w ith Front Red Light
- 230 Volt Cord Set and 4" Water Line
$ 81.50
0597 Heating Unit Kit (w iring included) for Models w ith Green Lighted
Rocker Sw itch - 120 Volt Cord Set and 4" Water Line
$ 81.50
0597A Heating Unit Kit (w iring included) for Models w ith Green Lighted
Rocker Sw itch - 230 Volt Cord Set and 4" Water Line
$ 81.50
0161A Heating Unit Assembly (no w iring included)
- 120 Volt and 4" Water Line
$ 62.50
0162A Heating Unit Assembly (no w iring included)
- 230 Volt and 4" Water Line
$ 62.50
21 0030 Brass 90 Degree Elbo w Joint
$
2.50
22 1130 3/8 "x1/4" Straight Brass Fitting for Heating Element Housing
$
2.50
23 0187 Copper Tube (4 " length) w ith Nuts and Compression Rings
$
4.00
24 0160 L -290 Thermostat
$
8.00
25 0195 Fusible Link Clamp
$
150
26 0151 Fusible Link Wire w ith Insulated Lug
$
3.00
27 0009 Bottom Plate w ith Casters $ 13.50
28 0011 Bottom Plate Casters (Set of 4)
$
6.50
29 0010 Scre ws for Bottom Plate (4 Scre ws Total)
$
0.75
ACCESSORIES
30 1050 Jiffy Steamer Assembly Wrench
$
4.00
0274 Brass Hat Nozzle Attachment $ 1300
0254 Metal Head/Wood Handle Hose Attachment Complete $ 70.00
0256 Metal Head I Wood Handle Only $ 37.50
0269 Replacement Wooden Handle (for Metal Steam Heads)
$
7.00
0262 Wig Hose Attachment $ 50.00
1062
Steam Cleaning " B" Brush Hose Attachment
$ 50.00
1063 Brush Only for the B" Hose Attachment
$
8.00
0898 Liquid Cleaner- 3 Ten (10) Ounce Bottles per Package'
$ 15.00
'Not Available for Export.
From the library of: Superior Sewing Machine & Supply LLC

Jiff~J-1/J-2/J-200 Wiring Diagram
Caution:
Insure that the power cord is
unplugged from the electrical
outlet before
attempting to
repair your Jiffy®Steamer.
From the library of: Superior Sewing Machine & Supply LLC

Jiffy® J-1/J-2/J-200 Wiring Instructions
Please note switch terminal numbers 2, 3, 5 and 6 indicated on
the enlarged switch diagram are marked on the actual switch.
Jiffy®Steamers manufactured before May 2000 are not
marked with the terminal switch numbers, but the terminal
blades are in the same location.
1. Insert cordset into housing and connectwhite neutral wire from cordset
bundle to terminal number 5
on the switch.
2. Connect blue wire from the right side
of heating element to the right side
of the L-290 thermostat.
3. Insert brass heating unit into housing and tighten with 2 mounting screws.
Connect green ground wire (from cordset) to the nearer
of the two mount-
ing screws.
(In older J-2s, groundwire may also be attached to internal
boss
of housing.)
4. Connect blackpositive wire from cordset to plastic connector on orange
fusible link wire.
5. Connect other end
of orange fusible link to terminal number 2
on the switch.
6. Connect yellow wire from the left side of the thermostat to terminal
number 3 on the switch.
7. Connect white wire from the left side of the heater unit to terminal
number 6 on switch.
8. Insert one end of copper water line and compression ring into threaded
fitting atbottom
of brass heating unit and tighten nut with a 5;8" wrench.
9. Connect other end of water line with compression ring to 90 degree brass
elbow at bottom
of water cup and tighten with a 5;8" wrench. (Heating unit
may be loosened and adjusted for a better fit if necessary.)
10. Set steamer upright and place blackplastic strain reliefapproximately
41;2" from end of cord and insert into housing using pliers.
11. Secure bottom plate with four screws.
12.
To avoid leakage, be sure and tighten hose (or hat nozzle) with wrench
before using steamer.
From the library of: Superior Sewing Machine & Supply LLC