JK-Products Ergoline Sunrise 480 User manual

SUNRISE
SUNRISE 480 LED ADVANCED PERFORMANCE
SUNRISE 488 LED DYNAMIC PERFORMANCE
1020036-00 / en / 10.2018
Operating instructions
Translation of the original operating instructions

Legal notice
2/68
Legal notice
Manufacturer: JK-Products GmbH
Köhlershohner Straße 60
53578 Windhagen
GERMANY
Tel.: [phone] / 818-140
Fax: [phone] / 818-166
Customer service /
Technical service
(Spare part orders for
components):
JK-International GmbH,
Division JK-Global Service
Köhlershohner Straße 60
53578 Windhagen
GERMANY
Tel.: [phone] / 818-861
Fax: [phone] / 818-205
E-mail: [email protected]
Spare part orders for
consumables:
JK-International GmbH,
Division JK-Licht
Köhlershohner Straße 60
53578 Windhagen
GERMANY
Tel.: [phone] / 818-600
Fax: [phone] / 818-615
E-mail: [email protected]
DANGER!
Failure to observe these instructions:
• can result in serious injury and death,
• can result in damage to the device and the
environment.
– Read these instructions carefully before putting this
tanning device into operation.
– Please observe the instructions and the code of con-
duct required to operate the device safely.
– Please make the instructions and additional information
from the manufacturer available to the personnel at
their workplace.
Copyright
The copyright remains with JK-Holding GmbH.
The contents may not be partially or completely duplicated, distributed or
utilized for competition purposes without authorisation or disclosed to other
parties.
The right to make technical changes in regard to the figures and information
contained in this instruction manual is reserved!

Table of contents
10/2018 1020036-00 Operating instructions – 3/68
Table of contents
1 Safety instructions and warnings................................................6
1.1 General ...........................................................................................6
1.1.1 Definitions .......................................................................................6
1.1.2 Symbol explanation.........................................................................7
1.2 Intended use ...................................................................................8
1.3 Foreseeable misuse........................................................................8
1.4 Tanning safety information..............................................................9
1.4.1 Prohibited usage .............................................................................9
1.4.2 Important notes .............................................................................10
1.4.3 Vibra Shape (Vibration plate) ........................................................ 11
1.4.4 Skin type descriptions ...................................................................13
1.4.5 Tanning times EN (UV type 2) ......................................................14
1.5 Safety instructions and warnings ..................................................16
1.5.1 Operator's obligations ...................................................................16
1.5.2 Personnel training .........................................................................16
1.5.3 Scope of delivery...........................................................................16
1.5.4 Transport, assembly and setup.....................................................16
1.5.5 Commissioning..............................................................................19
1.5.6 Operation and maintenance..........................................................19
1.5.7 Decommissioning..........................................................................20
1.5.8 Storage .........................................................................................20
1.5.9 Disposal ........................................................................................20
1.5.10 Directives ......................................................................................21
1.5.11 Export............................................................................................21
1.5.12 AUX (music, optional) ...................................................................21
1.5.13 Technical modifications.................................................................22
1.6 Signs and stickers on the device...................................................23
1.7 Warranty .......................................................................................26
1.8 Warranty and liability exclusions ...................................................26
2 Description ..................................................................................27
2.1 Scope of delivery...........................................................................27
2.1.1 Optional.........................................................................................27
2.2 Equipment.....................................................................................27
2.3 Device description.........................................................................28
2.4 Accessories (optional)...................................................................29
2.5 Functional description ...................................................................30
2.6 Description: vibration programmes ...............................................30

Table of contents
4/68
3 Operation .....................................................................................31
3.1 User safety information .................................................................31
3.2 Tanning - but correctly!..................................................................31
3.3 Application tips ..............................................................................33
3.4 Operating overview .......................................................................35
3.4.1 Navigation .....................................................................................36
3.5 Functions.......................................................................................37
3.6 Start...............................................................................................39
3.7 AUX (music) ..................................................................................40
4 Cleaning and maintenance.........................................................41
4.1 Safety instructions when
undertaking cleaning or maintenance work...................................41
4.2 Faults.............................................................................................42
4.3 Cleaning ........................................................................................42
4.3.1 Cleaning the surfaces....................................................................43
4.4 Lamps............................................................................................43
4.5 Cleaning plan ................................................................................44
4.6 Maintenance..................................................................................45
4.7 Maintenance plan..........................................................................46
4.8 Instructions for replacing the lamps...............................................48
4.8.1 Changing the chip card
(SUNRISE 488 LED DYNAMIC PERFORMANCE).......................49
4.8.2 Low pressure lamps ......................................................................50
4.8.3 Starter............................................................................................51
4.9 Cleaning or replacing lamps in the door........................................52
4.10 Cleaning or replacing lamps on the side walls ..............................53
4.11 AQUA / AROMA system maintenance ..........................................55
4.11.1 Changing the AROMA canister .....................................................55
4.11.2 Replacing the AQUA SYSTEM canister........................................56
4.12 Remote control: Replacing the batteries .......................................58
4.13 Maintenance performed by the customer service..........................58
5 Technical data .............................................................................59
5.1 Power, connection rating and noise level......................................59
5.2 Dimensions....................................................................................60
5.3 Lamp sets......................................................................................61
5.3.1 SUNRISE 480 LED ADVANCED PERFORMANCE......................61
5.3.2 SUNRISE 488 LED DYNAMIC PERFORMANCE .........................62
5.4 Spare parts and accessories.........................................................63

Table of contents
10/2018 1020036-00 Operating instructions – 5/68
6 Appendix......................................................................................64
6.1 JK timer controls ...........................................................................64
6.2 Equivalence key range..................................................................64
6.2.1 Description of the equivalence keys for UV fluorescent lamps .....65
7 Index.............................................................................................66

Safety instructions and warnings
6/68
1 Safety instructions and warnings
To ensure safe operation of the device, it is necessary to read the following
safety instructions and warnings carefully and comply with them.
The safety instructions summarized here are repeated in the corresponding
chapters, where necessary.
1.1 General
1.1.1 Definitions
Operator
Person who provides the devices described here to users on a commercial
basis. The operator is responsible for the correct operation of the device as
well as compliance with the maintenance intervals.
User
A person who uses the device at a commercial location.
Personnel
People who are responsible for the operation, cleaning and general mainte-
nance work and who instruct the users in the operation of the devices.
Electrician
A person with suitable professional training, knowledge, experience and
knowledge of the applicable regulations which enable them to identify and
avoid the dangers which can arise from working with electricity.
Authorized, trained and qualified personnel
Qualified staff from an external company who have been trained and author-
ized by the manufacturer to undertake assembly and maintenance work on
specific equipment.

Safety instructions and warnings
10/2018 1020036-00 Operating instructions – 7/68
1.1.2 Symbol explanation
The following types of safety notices are employed in these operating instruc-
tions:
DANGER!
Type and source of hazard
This safety notice indicates the existence of a direct danger
to body and life.
DANGER!
Type and source of hazard
This safety notice warns of dangers to body and life which
are caused by electricity.
WARNING!
Type and source of hazard
This safety notice warns of machine, material or environ-
mental damage.
NOTE:
This symbol does not identify any safety notices, but pro-
vides additional information to better understand the pro-
cesses.

Safety instructions and warnings
8/68
1.2 Intended use
This device serves the purpose of cosmetic tanning for one adult person with
skin suitable for tanning. Additional information is available on pages 13
and 31.
The device is only intended for commercial use, not for domestic use.
Some people are not permitted to use the device, see page 9.
The device may not be used by people with reduced physical, sensory or
mental capabilities or who have insufficient experience and/or knowledge
without supervision. A person responsible for their safety must ensure, either
by supervision or instruction, that the device is used correctly and safely. If
there is any doubt, use of the device by these people is prohibited!
The device may only be operated with the specified or equivalent lamps. The
tanning times given in this instruction manual are valid only for the specified
lamp set.
Any other use shall be considered improper. The manufacturer cannot be
held liable for damage or injuries resulting from this. The operator bears the
sole risk for this.
Intended use also includes compliance with the manufacturer’s instructions
and the operating and maintenance conditions. The device may only be oper-
ated, maintained and repaired by persons who are familiar with these tasks
and who have been informed of the dangers involved.
Vibra Shape Function
The vibration plate can be used additionally during the light application. The
vibration plate is used for muscle stimulation of healthy people. If required, the
vibration plate can also be operated independently of the lamps.
The vibration plate is not intended for medical applications!
The vibration plate should not be used by pregnant women or by people with
diseases and limited medical conditions. A list of the contra-indications can be
viewed on page 11.
1.3 Foreseeable misuse
The following uses of the device are explicitly prohibited:
 Multiple people may not use the device at the same time.
 People with a body weight of more than 150 kg may not use the device.
 Exceeding the specified tanning times may result in burns and long-term
skin damage.
 When the device is in use no other people may remain in the cabin, in
particular no children.
 People under 18 years of age may not use the device.

Safety instructions and warnings
10/2018 1020036-00 Operating instructions – 9/68
1.4 Tanning safety information
1.4.1 Prohibited usage
DANGER!
Danger of hearing damage!
Using earphones or headphones at high volume can result
in permanent hearing damage.
– Do not set the volume too high.
UV radiation
Danger of skin and eye injuries or skin diseases!
– Please observe the following instructions.
The following people may not use the device:
 People under 18 years of age
 People who cannot tan
 People who cannot tan in the sun whithout risking a sunburn
 People who easily sunburn when in the sun
 People with acute sunburn
 People who repeatedly suffered from serious sunburn during childhood
 People with naturally red hair
 People with atypically discoloured areas of skin
 People who have or have had skin cancer
 People who suffer from an increased risk of skin cancer (e.g. cases of
skin cancer in the family)
 People among whose closest relatives a melanoma has occurred
 People who are being medically treated for photosensitivity
 People taking photosensitivity causing medicine
 People with freckles and people who tend to develop freckles
 People with more than 16 moles on their body (2 mm diameter or larger)
 People with atypical moles (atypical moles are, for example, asymmet-
rical moles with a diameter greater than 5 mm, with varying pigmentation
and irregular edges)
– Seek medical advice without fail if in doubt!

Safety instructions and warnings
10/68
1.4.2 Important notes
All other people must observe the following instructions:
Danger of skin and eye injuries or skin diseases!
 The skin can become sunburnt when exposed to excessive radiation.
Excessive, frequently repeated UV radiation exposure from natural sun-
light or UV devices can result in premature ageing of the skin and an in-
creased risk of skin tumours.
 Particular caution is advisable for individuals who are especially sensitive
to UV radiation, and when certain medicaments or cosmetics are used.
Seek medical advice without fail if in doubt!
 UV devices should not be used without medical advice if unexpected
manifestations such as itching occur within 48 hours of first using the
sunbed.
 Increasing tanning requires increased exposure time (= radiation time) or
after a certain degree of tanning has been achieved, increased tanning is
not possible. However, the radiation time may not be extended as desired
within the scope of the permissible radiation doses! Therefore, only a cer-
tain level of final tanning, which depends on the skin type, can be
achieved without endangering your health.
 The tanning device may never be used when a filter panel is missing or
damaged, or the timer is defective!
Behaviour before, during and after a sunbath:
 During the tanning session no other people may remain in the cabin, in
particular no children.
 Remove all jewellery (including piercings) before the tanning session.
 Remove cosmetics before tanning and do not use sun screen products.
 Do not use any products intended to accelerate tanning.
 UV light can cause irreversible skin or eye damage. The unprotected eye
can become inflamed on the surface, and in certain cases the retina can
be damaged by excessive radiation. Cataracts can form after numerous
repeated tanning sessions. Use the UV-impermeable protective gog-
gles provided (order no. 84592-..). Contact lenses and sun glasses are
no substitutes for protective glasses.
 Protect sensitive skin areas such as scars, tattoos and genitals before
tanning.
 Observe the recommended tanning times.
 During a tanning session the quantity of radiation which results in the skin
reddening (MED, minimum erythema dose) may not be exceeded. If red-
dened skin occurs around 16-24 hours after the tanning session you may
not use the tanning device again for one week. After one week you can
start again from the beginning with the first tanning session in accordance
with the tanning table.
 The time between the first two sessions on the sunbed must be at least
48 hours! Do not take an additional sunbath on the same day.
 See a doctor if stubborn swelling, sores or pigmented moles form on the
skin.

Safety instructions and warnings
10/2018 1020036-00 Operating instructions – 11/68
1.4.3 Vibra Shape (Vibration plate)
Contra-indications
Risks of damage to health!
Vibrations can cause or aggravate health problems.
The following people are not allowed to use the equipment:
 Pregnant women
 People with DVT (Deep Vein Thrombosis)
 People with fresh wounds following an operation or surgery
 People with epilepsy
 People with acute illnesses / inflammations
 People with pacemakers
 People suffering from retinal detachment
 People with acute osteoporosis
People with the following illnesses may only use the device after con-
sultation with their doctor:
 Cardiovascular diseases
 Hip and knee implants
 Severe diabetes
 Severe migraine attacks
 Tumour diseases
 Gallstones or kidney stones
 Acute thrombosis
 Acute inflammation of the muscular-skeletal system
 New fractures to well-trained limbs
 New infections
 Acute hernia / intervertebral disc diseases / spondylolysis
 Rheumatoid arthritis
 Arthritic or arthropathic conditions (joint diseases)
People with recently implanted intrauterine devices (contraceptive coils),
metal pins, screws or plates are also only to use the device after consultation
with their doctor.

Safety instructions and warnings
12/68
Side effects
The use of the vibration plate may lead to the following side effects:
 Itching in regions of the body being trained
 Nausea and vertigo
 Rapid and brief drop in blood pressure
 Rapid hyperglycaemia in the event of diabetes
Diabetics should always have dextrose on hand! The side effects of nau-
sea, vertigo, drop in blood pressure and skin irritations are generally
harmless. Older users should be especially warned about the possibility
of vertigo and a sudden drop in blood pressure. People who have skin in-
juries such as blisters or wounds on the soles of their feet are not allowed
to use the vibration plate.

Safety instructions and warnings
10/2018 1020036-00 Operating instructions – 13/68
1.4.4 Skin type descriptions
DANGER!
Burns and long-term damage!
People with skin type I may not use the tanning device.
The following applies to people with skin types II, III and IV:
– Observe the tanning times.
– Observe the safety instructions.
NOTICE:
The tanning times are only valid for the lamp set and filter
panels specified on the sticker.
The tanning sessions should be at least 48 hours apart.
The maximum dosage of 25 kJ/m² per year should not be
exceeded.
Skin type II Skin type II Skin type III Skin type IV
Sensitive skin Light skin Normal skin Dark skin
Always/
frequently burns
Usually burns Sometimes burns Rarely burns
Tolerates only a
small amount of
natural sun.
Tolerates approx.
10-20min. of
natural sun.
Tolerates approx.
20-30min. of
natural sun.
Tolerates approx.
40 min. of natural
sun.

Safety instructions and warnings
14/68
1.4.5 Tanning times EN (UV type 2)
NOTICE:
 Observe the tanning times.
Observe the national requirements!
The tanning dosage of 3 kJ/m² per tanning period should not be exceeded.
SUNRISE 480 LED ADVANCED PERFORMANCE:
 UV low pressure lamps TREND ADVANCED 180 W E42 1509047-..
Number of
tanning sessions
Skin type I Skin type II Skin type III Skin type IV
[min] [min] [min] [min]
1 – 5 5 5
2 – 5 6 6
3 – 6 7 8
4 – 7 8 10
5 – 8 10 12
6 – 9 11 14
7 – 9 12 15
8 – 10 13 17
9 – 11 15 19
10 – 12 16 21
11 – 13 17 23
12 + – 14 19 25
Maximum number of
tannin
g
sessions per
year (NMSC):
– 85 63 48

Safety instructions and warnings
10/2018 1020036-00 Operating instructions – 15/68
SUNRISE 488 LED DYNAMIC PERFORMANCE:
 UV low pressure lamps
TREND ADVANCED DYNAMIC 180 E4 1005900-..
Number of
tanning sessions
Skin type I Skin type II Skin type III Skin type IV
[min] [min] [min] [min]
1 – 5 5 5
2 – 5 6 6
3 – 6 7 8
4 – 7 8 10
5 – 7 10 12
6 – 8 11 14
7 – 9 12 15
8 – 10 13 17
9 – 10 15 19
10 – 11 16 21
11 – 12 17 23
12 + – 13 19 25
Maximum number of
tannin
g
sessions per
year (NMSC):
– 80 55 42

Safety instructions and warnings
16/68
1.5 Safety instructions and warnings
1.5.1 Operator's obligations
As the operator you are responsible for providing clear operating, cleaning
and maintenance instructions and ensuring the intended use and the proper
operation of the device by means of training and instruction for the personnel.
Your operating instructions must enable the safe use and safe operation of
the device and take into account the characteristics and expertise of your
company and also the national work safety and environmental protection
regulations (within the European Union, the EU directive 89/391/EEC).
1.5.2 Personnel training
As the operator you are obliged to train your personnel and instruct them in
the established legal and accident prevention regulations. Ensure that your
personnel have understood and observe these operating instructions. This
applies in particular to the
 information in 'Intended use' and 'Foreseeable misuse'
 safety instructions in the 'Operation' chapter
 operating instructions
 cleaning and maintenance instructions
– Please make the instructions and additional information from the manu-
facturer available to the personnel at their workplace.
– Regularly check your personnel's safety consciousness and awareness
of the risks, taking into account your operating instructions.
– Please ensure that the cleaning intervals are complied with, in particular
cleaning after every tanning session.
– Please ensure that your personnel provide your customers with appropri-
ate advice, in particular regarding tanning times, possible risks and the
operation of the device.
– People under 18 may not use the device. Please instruct your personnel
to check the customer's identification in the event of doubt.
1.5.3 Scope of delivery
Information regarding the scope of delivery is contained in the 'Description'
chapter on page 27.
1.5.4 Transport, assembly and setup
The device is delivered by a specialist company and assembled and set up by
the manufacturer's own service personnel or by an authorized service com-
pany.
As an operator you are responsible for complying with the on-site ventilation
and electrical requirements at the setup location, see page 17.

Safety instructions and warnings
10/2018 1020036-00 Operating instructions – 17/68
Assembly
DANGER!
Personal danger due to electric shock or burns!
– The assembly and electrical connection must comply
with the national regulations.
– The on-site electrical installation must be fitted with an
easily accessible all-pole isolating device (master
switch), complying with overvoltage category III. This
means that each pole must have a contact opening
width complying with the conditions of overvoltage cat-
egory III for full isolation.
– If the connection is established via a plug-in connection
then the connection system according to EN 60309
must be utilized.
– Assembly, installation, up
g
radin
g
or repair of the device
may only be carried out by specially trained and author-
ized personnel.
Information regarding the disassembly and assembly of the device is availa-
ble in the separate assembly instructions. These assembly instructions are
intended solely for use by the manufacturer's service personnel or by qualified
specialists authorized by the manufacturer.
Ventilation
WARNING!
Risk of overheating due to air flow problems!
Operating faults possible.
– Do not change, obstruct or block the air inflow and
outflow to the device or make any unauthorized chang-
es to the device. The manufacturer shall bear no liabilit
y
for damage or injuries resulting from such actions.
– Observe the ventilation system data.
– Do not set up and operate the device on the transport
pallet!
Data regarding the air supply and ventilation planning is available in the plan-
ning manual (www.ergoline.de, available in English and German). You can
also obtain this data from your dealership or the customer service department
(see page 2).

Safety instructions and warnings
18/68
Setup location
WARNING!
Salty air! Contaminated air!
Device damage due to corrosion of the housing and electri-
cal components.
– Do not install the device at swimming pools.
– Do not operate the device in locations with aggressive
environmental conditions (e.g. air containing chlorine)
Damage to device possible!
Where there are great differences in temperature between
the transport route and the installation site the device may
not be put into operation immediately after being set up.
– Wait at least 2 hours before connecting the device to
the power supply.
Risk of overheating due to air flow problems!
Operating faults possible.
– Do not change, obstruct or block the air inflow and
outflow to the device or make any unauthorized chang-
es to the device. The manufacturer shall bear no liabilit
y
for damage or injuries resulting from such actions.
– Observe the ventilation system data.
– Do not set up and operate the device on the transport
pallet!
Environmental conditions
 Optimum ambient temperature: Between 15 °C and 32 °C
 Storage temperature: Between -15 °C and +60 °C
The device is not to be used outdoors.
Adaptation of the unit is required for operating altitudes greater than 2000 m
above sea level in order to guarantee trouble-free operation.
The device is not suitable for operation in mobile facilities (ships, buses,
trains). Adaptation of the unit is required in order to guarantee trouble-free
operation when used in mobile facilities.
Please contact the customer service department without fail before putting the
device into operation - see page 2.

Safety instructions and warnings
10/2018 1020036-00 Operating instructions – 19/68
1.5.5 Commissioning
DANGER!
Damaged mains power cable!
Danger to persons through electric shock or burns.
– Only the manufacturer or specialist companies are
permitted to replace the mains power cable.
Initial commissioning will be undertaken by the manufacturer's own service
personnel or by an authorized service company. The device will be handed
over ready for use.
If the device has not been used for a longer period of time, then it must first
be inspected by our customer service department or by another authorized
company before being put back into operation again.
The device is operated with an external time-control unit.
A time control unit must be attached so that the device automatically switches
off at the latest after < 110 % of the selected running time even if the control-
ler fails. The device running time must be provided with double protection by
use of a timer control that complies with the standard EN 60335-2-27.
Dependent on the local power supply company, the devices can transmit
interference to the power system of the building that impair the audio-
frequency remote control system used by the power supply company. This
can, for example, interfere with the function of night-storage heaters.
If faults occur due to the operation of the devices, then the operator is re-
sponsible for the installation of an audio frequency blocking device in the
building electrical installation. Please contact your electrician. The electrician
is familiar with the technical connection conditions of your local utility compa-
ny so that the audio-frequency blocking device can be matched to the power
system of your power supply company.
1.5.6 Operation and maintenance
Error-free operation, maintenance and service are required in order to ensure
that the health and safety of the users is not endangered during operation and
to ensure that the device is in a fault-free operating condition.
Please observe the information and recommendations provided in these op-
erating instructions. Please ensure that the intervals for the inspection,
maintenance and service are complied with. Please ensure that the lamps are
replaced after the specified usage time.
Unauthorized modifications and changes to the device and its control unit are
prohibited. Failure to comply with this invalidates the operating licence!
To avoid hazards, the device must not be used if the mains power cable is
damaged. A damaged mains power cable must be replaced by the manufac-
turer or their customer services, or by trained and qualified specialist person-
nel.

Safety instructions and warnings
20/68
1.5.7 Decommissioning
The device must be disconnected from the power supply in order to tempo-
rarily or permanently decommission it.
You must abide by the legal disposal requirements when permanently de-
commissioning the device.
1.5.8 Storage
Store the devices in a dry location with a stable temperature. Once the device
has cooled off, pack it in plastic wrapping to protect it against scratches.
 Storage temperature: Between -15 °C and +60 °C
1.5.9 Disposal
Environmental regulations –
disposal of lamps and batteries
UV lamps contain fluorescent materials and other waste containing mercury.
Batteries contain heavy metal compounds.
Within the European Union the national implementation of the Waste Frame-
work Directive 2008/98/EC applies. According to the national waste disposal
laws and in accordance with the municipal waste regulations, proof must be
provided of the proper disposal of UV lamps and batteries.
Your local sales agency will be happy to assist you with the disposal of UV
lamps and batteries:
– Inform your local agency of the number of UV lamps and batteries by
telephone or in writing.
The agency will then provide you with the name of a free delivery point for
your lamps or will take care, in conjunction with a disposal company, of the
collection and proper disposal of the lamps. This service is available for a fee.
Outside Germany, the respective national legislation applies. Please contact
your local sales agency.
Packaging
All packaging consists of 100 % recyclable materials. Packaging brought into
circulation by the JK Corporate Group that is no longer required can be re-
turned to the JK Corporate Group. Your partner agency or dealer will be hap-
py to advise.
Disposal of old devices
The device has been manufactured using recyclable materials. The JK Corpo-
rate Group will provide you with information on the content or potential haz-
ards of the materials used.
The manufacturer is obliged to take back and dispose of certain electrical and
electronic components in accordance with the 2012/19/EC Directive.