JL Audio stealthbox SB-POL-ACE/10TW1 User manual

Continued on Next Page
SB-POL-ACE/10TW1 INSTR_SKU# 011454
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.
With proper installation, your new vehicle-specific enclosed subwoofer system
will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your
authorized JL Audio dealer. The installation professionals employed by your
dealer have the necessary tools and experience to disassemble and reassemble
your vehicle properly. If you prefer to perform your own installation, please read
this installation guide completely before beginning the process.
If you choose to perform the installation yourself, it is absolutely
vital that the Stealthbox®be properly mounted to the vehicle
according to these instructions. Failure to mount the enclosure
properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the
enclosure caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a
collision or sudden deceleration.
INSTALLATION
D IFFI CULT Y:
ESTIMATED TIME:
1 HOUR
15
OUT
OF
Enclosure Type: Sealed
Driver Type: 10TW1-4
Nominal Impedance: 2 ohms
Continuous Power Handling: 600 watts (RMS method)
INSTALLATION GUIDE
for the
SB-POL-ACE/10TW1
SKU# 94628
2015 & Up Polaris Ace, Ace 570, & Ace 570 SP

INCLUDED HARDWARE
Continued on Next Page
Page 2 • JL Audio, Inc., 2016
SB-POL-ACE/10TW1 INSTR_SKU# 011454
Note: For optimum performance, JL Audio recommends applying the included Foam Strips (or sound damping material) to surrounding plastic panels to reduce unwanted vibrations.
* Pre-installed on enclosure
BOM ID Qty SKU Description
1 2 153714 1/4 - 20 x 1” Stainless Steel Button Head Screw
2 2 153716 1/4” Stainless Steel Split Lock Washer
3 2 153713 Stainless Steel Cushion Clamp
4 2 153717 M8 - 1.25 Nylon Lock Nut
5 2 153718 M8 - 1.25 x 40mm Flange Head Cap Screw
6* 2 153709 Rubber Bumper
7* 2 153715 #8 x 3/4” Phillips Pan Head Stainless Steel Screw
- 1 150249 Foam Strips (not shown)

POWER RECOMMENDATION
JL Audio recommends high quality ampliers such as the JL Audio MX500/1. The diagram below shows the recommended crossover settings for the MX500/1. For a detailed description of the
amplier settings, consult the owner’s manual for the amplier. If another amplier is being used, please reference this illustration and use similar settings on that amplier.
CONNECTIONS
Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your
Stealthbox® amplier. Other kits are available should you be using more than one amplier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for
both channels of the amplier. JL Audio recommends using 12AWG speaker wire for subwoofers such as the XC-BCS12-25.
Continued on Next Page
Page 3 • JL Audio, Inc., 2016
SB-POL-ACE/10TW1 INSTR_SKU# 011454

Page 4 • JL Audio, Inc., 2016 Continued on Next Page
STEP 6
It is recommended to use two people for Steps
6-7.
Slide the seat forward. Connect speaker cable
to the barrier strip on the bottom of the
enclosure, and slide the enclosure into
position, top first, as shown.
STEP 5
Pictured is one of the pre-installed Rubber
Bumpers on the bottom of the Stealthbox®.
These will sit into factory holes in the vehicle
in Step 7 to hold the base of the enclosure in
place.
STEP 4
Attach the two Stainless Steel Cushion Clamps
to the center, horizontal roll bar as shown.
The holes in the clamps should be facing the
rear of the vehicle. Slide both clamps to the
center of the roll bar to allow clearance for the
Stealthbox® installation in Steps 6-7.
STEP 3
Replace the factory bolts and nuts with the
included, shorter M8 - 1.25 x 40 mm Flange
Head Cap Screws and M8 - 1.25 Nylon Lock
Nuts as shown, and firmly tighten.
STEP 2
Remove the factory bolt and nut from the
horizontal section of the roll bar on both sides
of the vehicle. These will not be reinstalled.
STEP 1
Empty the cargo area of the vehicle.
SB-POL-ACE/10TW1 INSTR_SKU# 011454
STEP 8
Slide a Stainless Steel Cushion Clamp to each
of the outer edges of the roll bar, aligning the
holes in the clamps to the threaded inserts in
the top of the enclosure.
STEP 7
Push the bottom of the enclosure toward the
rear of the vehicle until the Rubber Bumpers
drop into the factory holes in the vehicle.

Page 5 • JL Audio, Inc., 2016
CONGRATULATIONS!
You have completed the installation for this model! Enjoy your new Stealthbox®!
SB-POL-ACE/10TW1 INSTR_SKU# 011454
STEP 9
Secure each of the Stainless Steel Cushion
Clamps to the enclosure using a 1/4 - 20 x 1”
Stainless Steel Button Head Screw and 1/4”
Stainless Steel Split Lock Washer, and fully
tighten.
STEP 10
Route the speaker cable as necessary.
Note: For optimum performance, we
recommend applying the included Foam Strips
(or sound damping material) to surrounding
plastic panels to reduce unwanted vibrations.
MID/HIGH FREQUENCY DRIVER FITMENT
VeX™ Enclosed Speaker Systems are ideal for powersports and o-road vehicle applications. Each
weatherproof pod can be mounted to a roll cage precisely aimed for optimum sound. Mounting
xtures are available to t a variety of roll cage diameters.
[phone]
www.jlaudio.com
JLA-SKU# 011454 • ver. 09.16.2016 • 10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, and “Stealthbox” and the Stealthbox logo are registered trademarks of JL Audio, Inc. “Ahead of the
Curve”, its respective logo, and “How we play” are trademarks of JL Audio, Inc.
Printed in USA • ©2016 JL Audio, Inc. • For more detailed information please visit us online at www.jlaudio.com.