JL Audio Stealthbox SB-D-5GRAMCCR/10TW3 User manual

INSTALLATION GUIDE
for the
SB-D-5GRAMCCR/10TW3
SKU# 94677
2019-Up Dodge Ram 1500 Crew Cab
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.
With proper installation, your new vehicle-specific enclosed subwoofer system
will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your
authorized JL Audio dealer. The installation professionals employed by your
dealer have the necessary tools and experience to disassemble and reassemble
your vehicle properly. If you prefer to perform your own installation, please read
this installation guide completely before beginning the process.
If you choose to perform the installation yourself, it is absolutely
vital that the Stealthbox®be properly mounted to the vehicle
according to these instructions. Failure to mount the enclosure
properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the
enclosure caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a
collision or sudden deceleration.
INSTALLATION
D IFF ICU LT Y:
ESTIMATED TIME:
2 HOURS
Enclosure Type: Sealed
Driver Type: 10TW3-D8
Nominal Impedance: 2 ohms
Continuous Power Handling: 800 watts (RMS method)
Continued on Next Page
25
OUT
OF
SB-D-5GRAMCCR/10TW3 INSTR_SKU# 011542

INCLUDED HARDWARE
21 3
4 5 6 7
Continued on Next Page
Page 2 • JL Audio, Inc., 2019
SB-D-5GRAMCCR/10TW3 INSTR_SKU# 011542
BOM ID Qty SKU Description
1 4 154090 M6 - 1 x 20 mm Hex Head Screw
2 4 154091 M6 Split Lock Washer
3 4 154092 M6 Oversized 18 mm OD Flat Washer
4 2 154093 Bracket
5 2 151096 3/8 “ Flat Washer
6 2 151081 3/8” Split Lock Washer
7 2 132323 3/8 - 16 x 1” Hex Head Bolt

POWER RECOMMENDATION
JL Audio recommends high quality ampliers such as the JL Audio XD600/1v2. The diagram below shows the recommended crossover settings for the XD600/1v2. For a detailed description of the
amplier settings, consult the owner’s manual for the amplier. If another amplier is being used, please reference this illustration and use similar settings on that amplier.
CONNECTIONS
Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your
Stealthbox® amplier. Other kits are available should you be using more than one amplier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for
both channels of the amplier. JL Audio recommends using 12 AWG speaker wire for subwoofers such as our XC-BCS12-25.
Continued on Next Page
Page 3 • JL Audio, Inc., 2019
SB-D-5GRAMCCR/10TW3 INSTR_SKU# 011542

Page 4 • JL Audio, Inc., 2019 Continued on Next Page
STEP 8
Fold the rear seats back down, then open and
lower the integrated center console.
STEP 7
Disconnect the indicated wiring harness under
the seat. Using an 18mm socket and wrench,
remove the two indicated rear seat bracket
bolts from the driver’s side rear seat.
STEP 6
Using an E12 socket and wrench, remove the
two front seat bracket bolts from the driver’s
side rear seat.
STEP 5
Carefully unclip and remove the storage
divider.
STEP 4
Using a 10mm socket and wrench, remove
the three screws from the side of the storage
divider bracket.
Repeat for the opposite side.
STEP 3
Turn the release handle to lower the storage
divider panel.
STEP 2
Fold the seat bottoms up.
STEP 1
Empty the rear seat area.
SB-D-5GRAMCCR/10TW3 INSTR_SKU# 011542

Page 5 • JL Audio, Inc., 2019 Continued on Next Page
STEP 16
Align the forward slot in the Bracket with the
threaded insert in the side of the enclosure.
Slide a 3/8” Split Lock Washer and a 3/8” Flat
Washer over each of two 3/8 - 16 x 1” Hex Head
Bolts, pass an assembly through the slot in the
Bracket, into the threaded insert, and hand
tighten.
Repeat for the opposite side.
STEP 15
Carefully place the Stealthbox into the vehicle.
Attach speaker cable to the terminal cup on
the back of the enclosure, and position the
enclosure between the two Brackets, as shown.
STEP 14
Align the two slots on the Bracket with the
factory holes on the inside of an outer seat
support frame, as shown. Slide an M6 Split
Lock Washer and an M6 Oversized 18mm Flat
Washer over each of two M6 - 1 x 20mm Hex
Head Screw, pass an assembly through each
slot in the Bracket, thread into a factory hole,
and hand tighten.
Repeat for the opposite side.
STEP 13
Carefully unclip and remove the outer seat
bracket trim panel on the driver’s side.
Repeat Steps 12-13 for the opposite side.
STEP 12
Carefully unclip and remove the driver’s side
rear door sill panel.
STE P 11
Repeat Steps 6-9 for the passenger side rear
seat, then remove the seat from the vehicle.
STEP 10
Using a T50 Torx socket and wrench, remove
the factory seat belt bolt from the floor behind
the passenger side seat.
STEP 9
Reach over the center console, behind rear
seat back, and pull the indicated seat release
loop to unhook the latch and release the seat.
Carefully remove the seat from the vehicle.
SB-D-5GRAMCCR/10TW3 INSTR_SKU# 011542

Page 6 • JL Audio, Inc., 2019
CONGRATULATIONS!
You have completed the installation for this model! Enjoy your new Stealthbox®!
All specifications are subject to change without notice. “JL Audio®” and “How we play®” are registered trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo are trademarks
of JL Audio, Inc.
Printed in USA • ©2019 JL Audio, Inc. • For more detailed information please visit us online at www.jlaudio.com.
[phone]
www.jlaudio.com
JLA-SKU# 011542 • ver. 10.29.2019 • 10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA
®
MID/HIGH FREQUENCY DRIVER FITMENT
A variety of JL Audio coaxial and component systems will t in the factory speaker locations of your vehicle.
1 - Installation may require adaptor, 2 - Component woofer only
STEP 17
Push the enclosure toward the rear of the
vehicle, then fully tighten the two M6 - 1 x
20mm Hex Head Screws on each side of the
enclosure.
Fully tighten the 3/8 - 16 x 1” Hex Head Bolt on
each side of the enclosure.
SB-D-5GRAMCCR/10TW3 INSTR_SKU# 011542
STEP 19
Fold the seat bottoms back down.
STEP 18
Route the speaker cable as necessary.
Reinstall the outer seat bracket trim panels,
rear door sill panels, rear seats, and seat belt.
Location / OEM
Speaker Size
Suggested JL Audio Speaker Models
Coaxial Models Component Models
Front Dash /
3-1/2-inch C2-350x C7-350cm
Front Doors /
6 x 9-inch
C1-690x(1), C1-690tx(1), C2-690tx(1)
C2-650x(1), C5-650x(1)
C1-690(1), C1-650(1),C2-650(1),
C3-650(1), C5-650(1), C7-650cw(1,2)
Rear Doors /
6 x 9-inch
C1-690x(1), C1-690tx(1), C2-690tx(1)
C2-650x
(1)
, C5-650x
(1)
C1-690(1), C1-650(1),C2-650(1),
C3-650
(1)
, C5-650
(1)
, C7-650cw
(1,2)