JL Audio Stealthbox SB-SC-XBG1/10W1v3 User manual

INSTALLATION GUIDE
for the
SB-SC-XBG1/10W1v3
SKU# 94435
2004 - 2006 Scion xB
Thank you for choosing a JL Audio Stealthbox®for your automotive sound system. With proper installation, your new
vehicle-specific enclosed subwoofer system will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox®installed by your authorized JL Audio dealer. The
installation professionals employed by your dealer have the necessary tools and experience to disassemble and
reassemble your vehicle properly. If you prefer to perform your own installation, please read this installation guide
completely
before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox®be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
STEP 1
Remove the passenger seat from the vehicle, make sure to
unplug the seatbelt sensor.
Continued on Next Page
STEP 2
Place the two included 3” x 3” Wax Squares as indicated at
left.
STEP 3
Thread the two included 3/8-16 x 2 1/4” Set Screws into the
threaded inserts in the Stealthbox® leaving approximately
1/2” exposed.
SB-SC-XBG1/10W1v3 INSTR_SKU# 011283
INSTALLATION
DIFFICULTY:
25
OUT
OF
ESTIMATED TIME:
12 HOURS

SB-SC-XBG1/10W1v3 INSTR_SKU# 011283
STEP 7
Install included hardware as shown on each of the 3/8-16
x 2 1/4” Set Screws. Connect the wire from the amplifier,
re-install the seat that was removed at the start, plug in the
seatbelt sensor that was unplugged.
CONGRATULATIONS!
You have completed the installation for this model!
Enjoy your new Stealthbox®!
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
STEP 6
Using the identations made in Step 5 as a guide, drill a 1/2”
hole through the floor in both locations.
*CAUTION*
Before drilling, always make sure that you are not
going to be drilling into any gas lines, brake lines,
transmission lines, electrical wiring, exhaust systems
or anything else that might cause a reduction in
your weekly pay. Always wear eye protection when
drilling.
STEP 5
If indentations are not produced as shown after Step 4, back
the 3/8-16 x 2 1/4” Set Screws out of the enclosure in 1/8”
increments and repeat Step 4 until there are two clearly
defined indentations in the 3” x 3” Wax Squares.
Once the identations are made, back out the 3/8-16 x 2 1/4”
Set Screws until approximately 1 1/4” is exposed. This is also
a good time to verify the performance of the subwoofer
before mounting it.
STEP 4
Place the enclosure in position, pushing down so that
indentations are produced in the 3” x 3” Wax Squares as
shown in Step 5.
Page 2 • JL Audio, Inc 2014
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc.“Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU# 94435- 10.26.2015 • Printed in USA • ©2008 JL Audio, Inc. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902 #6,243,479
#6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign patents pending.
For more detailed information please visit us online at www.jlaudio.com.
[phone]
www.jlaudio.com
10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA
INCLUDED HARDWARE
2) 3/8” Split Lock Washer 2) 3/8” x 1 1/4” Fender Washer
2)3/8-16 x 2 1/4” Set Screw 2) 3/8-16 Hex Nut
2) 3” x 3” Wax Square
SPECIFICATIONS
Enclosure Type: Acoustic Suspension (sealed)
Driver Type: 10W1v3-2
Nominal Impedance: 2 Ohms
Continuous Power Handling: 300 Watts
POWER RECOMMENDATION
JL Audio recommends using a high quality amplifier such as the JL Audio XD300/1v2. The diagram below shows
the recommended crossover, infrasonic filter and equalizer settings for the XD300/1v2 when being used to power
your Stealthbox®.
The JL Audio XD300/1v2 is a very versatile audio component. Please consult the owner’s manual for even more
detailed information about installing and tuning this amplifier.
MID/HIGH FREQUENCY DRIVER FITMENT
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location: 6 1/2””- Front Doors
Fits JL Audio Models: TR650-CXi, TR650-CSi, C2650, C2650-X, C5-650, C5-650x & ZR650-CSi
Rear Speaker Size / Location: 6 1/2”- Rear Door
Fits JL Audio Models: TR650-CXi, TR650-CSi, C2650, VR650X,
C5-650, C5-650x & ZR650-CSi