JL Audio Stealthbox SB-VW-GTI/10TW3 User manual

INSTALLATION GUIDE
for the
SB-VW-GTI/10TW3
SKU# 94572
2006 - 2013 Volkswagen GTI MkV, Rabbit & R32
Thank you for choosing a JL Audio Stealthbox®for your automotive sound system. With proper installation, your new
vehicle-specific enclosed subwoofer system will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox®installed by your authorized JL Audio dealer. The
installation professionals employed by your dealer have the necessary tools and experience to disassemble and
reassemble your vehicle properly. If you prefer to perform your own installation, please read this installation guide
completely before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox®be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
STEP 1
Remove any contents from the cargo area.
Continued on Next Page
STEP 2
Place the supplied wax square onto the driver’s side rear
cargo panel.
STEP 3
Thread the supplied socket cup screw into the rear of the
Stealthbox®.
SB-VW-GTI/10TW3_INSTR_SKU#011250
13 1/2 inches
INSTALLATION
DIFFICULTY:
25
OUT
OF
ESTIMATED TIME:
1 HOUR
6 inches

Continued on Next Page
SB-VW-GTI/10TW3_INSTR_SKU#011250
STEP 5
Note: Before drilling, you are drilling into the rear
fender well. Once you protrude to the outside, do not
go any further or you will be paying for a new rear
tire. Always wear eye protection when drilling!
With a drill and a 1/2-inch drill bit, drill through the
impression made in the wax square.
Remove the wax square.
STEP 4B
The Stealthbox® will be raised off the floor. This is to allow
the factory flooring to be pulled from the cargo area, once
the Stealthbox® is installed.
STEP 4A
The Stealthbox® needs to fit all the way to top plastic panel.
*Read the next three steps to fully understand
this procedure.*
STEP 4
Place the Stealthbox® into the mounting location and press
firmly onto the Stealthbox®.
Page 3 • JL Audio, Inc 2016
STEP 7
Place the Stealthbox® into the mounting location. Guide the
socket cup set screw through the drilled hole.
STEP 9
Behind the strut, pull the black plastic guard to gain access to
the protruding socket cup set screw.
STEP 8
Jack up the driver’s side rear of the vehicle.
You should be able to access the socket cup set screw with
the rear wheel on the car. If necessary, you may remove the
wheel off the car.
STEP 6
Run speaker wire from the amplifier’s location to the
Stealthbox®location and check for proper operation of
the woofer.

SB-VW-GTI/10TW3_INSTR_SKU#011250
CONGRATULATIONS
You have completed the installation for this model!
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
STEP 10
Place a supplied fender washer, flat washer, split lock washer
and hex nut onto the socket cup set screw. Secure, but do
not over tighten.
Note: For added protection it is recommended that
you apply a bead of silicone between the vehicle and
the fender washer. After the bolt assembly is tightly
secured, it is also recommended that vehicle under-
coating material is applied to the exposed assembly
Page 3 • JL Audio, Inc 2016
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc.“Ahead of the Curve”and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU# 011250 - 09.20.2016 • Printed in USA • ©2016 JL Audio, Inc.
For more detailed information please visit us online at www.jlaudio.com.
[phone]
www.jlaudio.com
10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA
INCLUDED HARDWARE
(1) 3/8-inch -16 x 2 1/2-inch Socket Cup Set Screw (1) 3/8-inch -16 Hex Nut
(1) 3/8-inch Fender Washer (1) 3” x 3” Wax Square
(1) 3/8-inch Flat Washer
(1) 3/8-inch Split Lock Washer
SPECIFICATIONS
Enclosure Type: Acoustic Suspension (sealed)
Driver Type: 10TW3-D4
Nominal Impedance: 2 ohms
Continuous Power Handling: 400 Watts
POWER RECOMMENDATION
JL Audio recommends using a high quality amplifier such as the JL Audio XD300/1v2. The diagram below shows
the recommended crossover settings for the XD300/1v2 when being used to power your Stealthbox®.
The JL Audio XD300/1v2 is a very versatile audio component. Please consult the owner’s manual for even more
detailed information about installing and tuning this amplifier.
MID/HIGH FREQUENCY DRIVER FITMENT
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location: 6.5-inch / Front Doors
Fits JL Audio Models: TR650-CSi, TR650-CXi, C2-650, C2-650x,
C3-650, C5-650, C5-650x & ZR650-CSi
Rear Speaker Size / Location: 6.5-inch / Rear Doors / Side Panels
Fits JL Audio Models: TR650-CSi, TR650-CXi, C2-650, C2-650x,
C3-650, C5-650, C5-650x & ZR650-CSi