JL Audio Stealthbox SB-N-MURAN/10W1v2 User manual

➔
➔
➔
➔
Stealthbox®
INSTALLATION GUIDE
SB-N-MURAN/10W1v2, JL AUDIO, Inc 2006 Sheet SKU#011197 Revision1/18/2006Page 1
for the
SB-N-MURAN/10W1v2
(2003-Up Nissan Murano)
This Stealthbox is a product which
requires professional installation skills and
tools.
Please read this installation guide thor-
oughly before beginning the project. It
will guide you step by step through the
installation.Several of the steps in this
process may require two people to
accomplish.
It is absolutely vital that the enclosure
be properly mounted to the vehicle
according to these instructions. Failure
to mount the enclosure properly pres-
ents two problems: 1)The sub-bass
performance will suffer due to the
movement of the enclosure caused by
the force exerted by the woofer(s) and
2) A loose enclosure presents a serious
safety hazard in the event of a collision
or sudden deceleration.
Please enjoy your JLAudio Stealthbox
responsibly.
STEP 1: Remove all contents,rubber flooring,
cargo shade and lower the rear seats.
STEP 2: Open the cargo flooring and hook it
to the upper lip of the tailgate opening.
Remove the organizer tray,wooden board,
factory woofer enclosure, spare tire and the
driver’s side cargo pocket cover.
STEP 3: a)With a Phillips® screw driver,
remove the driver’s side cargo pocket.
b)Unsnap the wiring harness that is running
from front to back,on the floor.
STEP 4: This picture is looking from the back-
seats to the tailgate opening,showing the tail-
gate sill plate.
To remove the sill plate;Pop out the middle of
these three tabs and then pull out the outer
piece from the sill plate.
STEP 5: With a small flat blade; pop out the
oval plastic cover of the tailgate sill plate,that
is located under the tailgate hook latch.
The sill plate now can be lifted up and
removed out of the vehicle.
STEP 6: Look to the front left of the cargo
area for the two factory bolts that are secur-
ing a black plate to the floor.
Remove the left side bolt only.
START
HERE
Continued on Next Page ➔
www.jlaudio.com
➔
➔
➔
➔
➔
➔

➔➔
➔➔➔
STEP 7: There is a large L-bracket that is already
mounted to the rear of the Stealthbox®.This L-
bracket needs to be unmounted, flipped around and
remounted.The picture above shows the large L-
bracket properly mounted, with the woofer facing
down.
STEP 11: To access this mounting location; enter
the vehicle via the driver’s side rear passenger door,
lift up the flooring that is laying on the second row
seat.
Place a supplied 1/4” FlatWasher onto the
8mmx35mmx1.25” Hex Bolt.
Line up the angle bracket mounting hole to the fac-
tory bolt hole. Place the bolt assembly through the
angle bracket and thread into the factory bolt hole.
Do not tightly secure.
Cont.
From
Previous
Page
Continued on Next Page ➔
➔
STEP 8: a)Place a supplied 3/8” lock washer and
3/8” flat washer onto a 3/8”-16x1-1/4” hex bolt.
Using this bolt assembly, secure the supplied
small L-bracket onto the front of the
Stealthbox®,as is in the picture above.
b)With the Stealthbox® placed into the cargo area.
Run speaker wire from the amplifier location to the
Stealthbox’s® wire terminal and secure.
STEP 12: With Stealthbox loosely mounted in the
front, use the rear L-bracket mounting hole as a drill
guide. *CAUTION*
Before drilling, make sure that you are not going to
be drilling into any gas lines, brake lines, transmission
lines, electrical wiring or anything else that might
cause a reduction in your weekly pay.Always wear
eye protection when drilling.
With the use of a 3/8” drill bit and drill. Drill out the
floor.
➔
VEHICLE'S FLOOR
LOCK WASHER
HEX HEAD BOLT
FLAT WASHER
HEX NUT
FLAT WASHER
L-BRACKET FROM STEALTHBOX
FENDER WASHER
STEP 13: With the supplied hardware, place a
3/8” FlatWasher onto the 3/8”hex bolt. Place the
bolt assembly through the angle bracket and drilled
hole, from inside the vehicle.
From the underside of the vehicle, place a
3/8” Fender Washer, 3/8” Flat Washer, 3/8” Lock
Washer and the 3/8”-16 Hex Nut onto the pro-
truding bolt. Secure tightly.
Now, tightly secure the front mounting bolt assem-
bly, from STEP11.
STEP 14: Not pictured:Place the spare tire,
hardboard and hold down wing threaded rod back
into place.
The picture above is the under side of the driver’s
side rear cargo pocket floor, that was removed in
STEP2.
Remove the three positing tabs,indicated by the
white arrows.
STEP 9: Place the Stealthbox® into position.The
speaker terminal needs to face to the front of the
vehicle.
Position the factory wiring harness around the out-
side of the front right corner of the Stealthbox®.
STEP 10: Tuck the rear of the factory harness
under the right rear corner.The harness needs to
pass between the woofer and the rear L-bracket.
*Make sure that the harness is not under the
woofer*.
SB-N-MURAN/10W1v2, JL AUDIO, Inc 2006 Sheet SKU#011197 Revision1/18/2006
Page 2
www.jlaudio.com
➔
➔
➔
➔

Specifications:
Enclosure Type: Sealed
Driver Type: 10W1v2-4
Nominal Impedance: 4Ω
Cont. Power Handling: 150Watts
JLAudio recommends using a high quality amplifier such as the JLAudio e2150. The diagram below shows the recommended
crossover, infrasonic filter and equalizer settings for the e2150 when being used to power your Stealthbox®.
Included Hardware:
1) 1/4” USS FlatWasher
1) 3/8”-16x1-1/4” Hex Bolt
2) 3/8” Split LockWasher
2) #6x3/8” Philip® Head Screws
1) 3/8”-16x1-3/4” Hex Bolt
3) 3/8” FlatWasher
1) 3/8” x 1-1/4” FenderWasher
1) 2”x1-1/4”x1” 3-Hole L-Bracket
1) 3/8”-16 Hex Nut
1) 8mmx35mmx1.25” Hex Bolt
2) Round Dual Lock Fastener
10369 N. Commerce Pkwy, Miramar, Florida 33025-392 Phone: [phone] Fax: [phone]
The JLAudio e2150 is a very versatile audio component. Please consult the owner’s manual for detailed information
about installing and tuning this amplifier.
➔➔➔
STEP 15: a) Lower the flooring back into position,
from STEP 2.
b) Place the driver’s side floor cargo pocket panel
back into place. Pick up the left side of the panel
and stand it up on it’s right edge, just right of the
pair of the
round dual lock fastener .As shown in
the picture above.
c) Mark the under side of the floor panel, of the
location of the round dual lock fastener .
STEP 16: a) Flip over the side floor panel.
Measure 1-1/2” from the outside left edge to the
right.This measurement needs to line up with the
round dual lock fastener position markings
made in STEP 15. Mark the final location.
b) With the pair of supplied round dual lock fasten-
er and the pair of #6x3/8” Phillips® screws. Mount
the round dual lock fastener to the under side of
the floor panel at the markings.
STEP 17: Snap the driver’s side rear cargo pocket
cover into place.
➔
SB-N-MURAN/10W1v2, JL AUDIO, Inc 2006 Sheet SKU#011197 Revision1/18/2006Page 3
www.jlaudio.com
Mid/High Frequency Driver Information:
CONGRATULATIONS!
INSTALL COMPLETE.
VR690-CXi
VR650-CXi
Front Location Driver Size:
6x9
Applicable JL Audio Products:
TR690-TXi &VR650-CXi
Rear Location Driver Size:
6.5”
Applicable JL Audio Products:
TR,VR & XR650-CXi
Cont.
From
Previous
Page
Difficulty Of Installation:
1-1/2”