14. Do not leave the appliance unattended when in use.
15. This heater is not intended for use in bathrooms, laundry and similar indoor locations, never located heater where it may fall into a
bathtub or another water container.
16. No liability can be accepted for any damage caused by non compliance with these instructions or any other improper use or mishandling.
17. This appliance is not intended for use by persons (including children) with reduces physical, sensory or mental capabilities or lack of
experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person
responsible for their safety. Children and vulnerable people should be supervised to ensure they do not play with the appliance.
18. If the supply cord is damaged in any way, it must be replaced by the manufacturer or its service agent or a similarly qualified person in
order to avoid a hazard.
19. To prevent overheating of this appliance, keep the air inlets and outlets clean and free of anything that may cause blockage.
Check all inlets and outlets from time to time to ensure it is clear of any dirt or dust accumulation. DO NOT COVER.
20. Parts of the heater may exceed 200oC, contact with the heating tube, reflector, or mental parts near the heating tube, may cause
severe BURNS. To avoid burns, do not let bare skin touch hot surface.
21. NEVER place hands under the heating elements. ALWAYS allow heating element to cool at least 10 minutes before touching the heating
tube or adjacent parts.
22. This product contains recyclable materials. Do not dispose this product as unsorted municipal waste. Please contact your local municipality
for the nearest collection point.
INTRODUCTION
The SUNRAD RAINBOW carbon infrared heaters produce instant and comfortable heat like the sun. These robust and weatherproof heaters are
designed for domestic and commercial heating applications within indoor and outdoor areas.
MODEL SUNRAD RAINBOW
Voltage(V) 220-240VAC
Wattage(W) 2000
Amps(A) 8.3-9.0
Btu(HR) 6825
Dimensions W×H×D(mm) 879×195.3×84.7
Weight(KG) 3.0
INSTALLATION
Tools Needed: * Pencil *Hammer *Level *Screw Driver *Power Drill and drill bits
A wall mounting bracket is provide with the heater which has been specifically designed to allow this product to be fitted to a wall or ceiling
before drilling the holders for the wall/ceiling is solid and that there are no hidden water pipes or electric wires. The heater must be installed
no less than 16’’ from side walls and no less than 6”’ off the floor.
ATTENTION! The appliance must be installed on the solid surfaces like concrete, wood or metal etc.
Important: Ensure that the supply cables are well mounted and that it does not come into contact with reflector of the heater or that does
not trail into heated area, the supply cable can be fixed to the metal mounting bracket behind heater with plastic zip ties.
1. This heater should be installed by a competent person, i.e. a qualified electrician.
2. Always disconnected the heater from the electricity supply and allow it to cool before installation.
3. This heater can be mounted in a horizontal or vertical manner, but for a higher efficiency we recommend horizontal usage.
4. For both wall and ceiling mounting, the lowest part of the heater must be located at or above a minimum height of 1.8m from ground level,
so that the heater can not be touched when in operation.
5. For wall mounting, there must be a 1.8m distance from your appliance to the ground. For ceiling mounting, there must be a 2.4m distance
from your appliance to the ground.
6. For both horizontal and vertical mounting on the wall, there must be a min. distance of 0.4m between the appliance and the ceiling.
7. The distance from your appliance from the corners should be min. 0.4m for vertical use and min. 0.5m for horizontal use.
8. When installed to the ceiling, there must be a distance of 0.5m between corners and the appliance.
9. The distance of your appliance from the living beings is to be min 1m.
10. The distance from the front side of the heater to materials such as wood, carton, cloth etc., must be min 1m.
11. When mounting horizontally or to a ceiling, do not position the heater at an angle more than 90°and less than 45°.
12. The supply cable must be at the lower end of the heater if the heater is installed at an angle or vertically.
13. Keep the supply cord away from the body of the heater which will get hot during use.
14. Do not install the heater on an inflammable surface.
15. Observe the minimum safe distance between the heater body and the inflammable surfaces when mounted.
16. The heater should always have a minimum clearance of 0.5m from a ceiling and adjacent walls.
17. If the heater is to be used outside, a weatherproof outlet is recommended.
18. Before drilling ensure that there are no wires or water pipes in the area where the heater is to be installed.
19. The heater must be installed on the mounting brackets provided.
