Jntech JNPH1AF User manual

Outlet Filter
user manual
JNPH1AF
JNPH2AF
JNPH3AF

The copyright belong to Supplier.
This document involves the proprietary and confidential information about High
voltage solar charger of Supplier. It strictly prohibited to disclose the document
by duplicating, photocopying, publishing online and in other forms without
Supplier’s permission.
Supplier. reserves the right to change details in this publication without notice.
V1.0

I
Preface
Manual Instruction
This manual describes the transportation, installation, operation, maintenance
and troubleshooting of the following SUPPLIER Outlet Filter (Short as filter).
●JNPH1AF
For JNP2K2H/JNP3KH/JNP3K7H/JNP4KH/JNP5K5H/JNP7K5H
solar pumping system.
●JNPH2AF
For JNP11KH / JNP15KH/ JNP18K5H solar pumping system.
●JNPH3AF
For JNP22KH/ JNP30KH/ JNP37KH/ JNP45KH/ JNP55KH solar
pumping system.
In order to describe conveniently later, there is no distinguish between
JNPH1AF, JNPH2AF, JNPH3AF, They will be short for JNPH x AF.
Target Reader
This manual applies to the professional engineering and technical person who
is responsible for installing and operating of outlet filter.
Use the Manual
Please read this manual carefully before installing and operating outlet filter.
Please keep this manual well for operation and maintenance in future.
The manual content would be constantly updated and revised, but it
unavoidably has slightly discrepancies or errors with real outlet filter, please
kind prevails if user purchases our outlet filter.
Symbol Used
The following safety symbols may be used in this manual, and the
meanings are shown in below.
Safety Symbol
Meaning
Danger
Means that it may lead to serious accident of injuries, if
safety warning is ignored.
Warning
Means that it may lead to serious accident of injuries,
equipment serious damage or main business interruption, if
safety warning is ignored.
Notice
Means that it may lead to moderate accident of injuries,
equipment moderate damage or part of the business
interruption, if safety warning is ignored.

II
Noted
Means that the content is additional information.
Outlet Filter related symbols:
Symbol
Meaning
AC power.
Refer to relevant instructions
Cannot discard Power Pack together with domestic garbage.
Beware of dangerous high-voltage.
Should wait for 5 minutes after outlet filter and AC power
are disconnected, then Power Pack only can be touched.
Beware of hot surface
The Power Pack temperature can exceed 60℃during operation.

III
Content
Preface.............................................................................................. I
Manual Instruction ..................................................................... I
Target Reader............................................................................. I
Use the Manual........................................................................... I
Symbol Used .............................................................................. I
1Outlet Filter Unpacking.................................................................. 1
1.1Accessories Unpacking........................................................ 1
1.2 Dimension ........................................................................... 2
1.3 Identify Filter....................................................................... 2
2 Installation Procedure................................................................... 3
2.1 Installation Tool................................................................... 3
2.2 Installation Location............................................................ 3
2.3 Installation of Outlet Filter .................................................. 4
3 Electrical Connection.................................................................... 6
3.1Outlet filter system installation and connection .................. 6
3.2 Outlet Filter Internal Wiring................................................. 6
4 Usual malfunctions and maintenance........................................... 8
Attached List 1................................................................................. 9

1
1 Outlet Filter Unpacking
1.1Accessories Unpacking
Supplier. Supplies standard outlet filter and common accessories as
following:
Figure1-1 Outlet filter and standard accessories
Table1-1 Outlet Filter and Accessories Table
No.
Introduction
Delivery State
1
Outlet Filter
Standard
2
Fixing Rail
Standard
3
Expansion Bolt
Standard
4
Cool pressure terminal
Standard
5
Packing List
Standard
6
User Manual
Standard
7
Certificate of Approval
Standard
12 3
456 7

2
1.2 Dimension
Figure1-2 Outlet filter dimension figure
Table1-1 Outlet Filter Dimension
Model
Width (mm)
Height (mm)
Depth(mm)
Net weight
JNPH1AF
260
520
150
14.5
JNPH2AF
260
520
150
17.5
JNPH3AF
350
544
215
34
1.3 Identify Filter
The nameplate in the side of filter, and it shows the filter model, some
important parameter and certificate mark.
Table 1-2 Nameplate information table
No.
Description
1
SUPPLIER Logo and name
2
Filter model and parameter information
3
Certificate and safety signs
4
Company and website
W
H
D
1
2
3
4

3
2 Installation Procedure
2.1 Installation Tool
The installation of AC filter and wire should use tools as following, user
can select proper tools according to experience.
Table2-1 Installation tool list
schematic
Name
Specification
Function
Crimping Pliers
M10
For connecting wire’s
processing
Electric Drilling
Ф8
For hole drilling
Cross
Screwdriver
Ф8
For wire connection of
AC input terminal
Open Spanner
10#
To fasten expansion bolt
2.2 Installation Location
Outlet filter shall be installed at vertical and backward inclination, max.
inclination angle should be 10°.
Fig.2-1 Installation diagram
√
√
Min 80。
×
×

4
Fig. 2-2 Outlet Filter min. spatial size figure
As figure2-2 show outlet filter shall be installed on right side of inverter.
Please do keep the distance between inverter and outlet filter over
100cm.
Table2-2 Min. spatial size marking
Location
Min. Separable
Upward
100cm
Downward
100cm
Both sides
100cm
Front
100cm
2.3 Installation of Outlet Filter
Step1: Four lugs following with outlet filter should be fixed in the corner
of outlet filter by using screwdriver, as the fig. show:
Fig.2-3 Outlet filter lugs sketch map
Top lugs
Bottom lugs
100cm100cm 100cm
100cm 100cm
100cm
100cm
100cm
100cm

5
Step2: Drilling hole in selected site according to the size and shape of
board, It is recommend that the hole diameter should 10+1/-0
and depth is 60+5/-0.
Fig. 2-4 JNPHxAF Mounting hole location
Step3: Let expansion bolt in hole, hange the lugs on expansion bolt as
fig. 2-4 showing, and use the spanner to fasten expansion bolt.
Use the expansion
bolt to fixed board on
the wall.
230mm
495
mm

6
3 Electrical Connection
3.1Outlet filter system installation and connection
The outlet filter connected between inverter and water pump. System
optimization for long cable reflect in the following 3 points:
(1)Effective control of motor reflected voltage, protect motor
insulation, prolong the lifespan of pump;
(2)Effective suppress the surge voltage on the electric cable, protect
inverter power module;
(3)Filter out PWM control high frequency harmonic, pump running
more stable, improve system efficiency.
Fig.3-1 Outlet filter system connection sketch map
Input and output terminal of outlet filter installed in the bottom, all of
them are M25 water-proof, as is showing Fig.3-2.Output cable switch
in outlet filter through the terminal of “INVERTER”, and output cable
of outlet filter switch in terminal of pump motor through “MOTOR”
3.2 Outlet Filter Internal Wiring
There are input and output terminal, users need to open the latch in the
bottom right side and bottom cover plate. Output cable of inverter
connected “U, V, W” three phase terminal array and cable of pump
connected with “A, B, C” three phase terminal array respectively, as the
Fig. showing:
inverter filter pump

7
Fig.3-2 Bottom view of outlet filter Fig.3-3 Internal Terminal
Close the bottom cover plate and lock catch when finish wire connection.
And the bottom over plate in an open condition is strictly prohibited.
Then the outlet filter connection has been completed.
U V W A B C
PE

8
4 Usual malfunctions and maintenance
Solutions to typical faults and states.
Table4-1 Running exception handler table
Situation
Possible Reason
Solution
Display output phase
failure when inverter
running.
Outlet filter wiring
get loose.
Turn off inverter and open filter’s
cover plate to check if wiring
terminal compressed and test U-A,
V-B and W-C by multimeter.

9
Attached List 1
Solar Pumping System configuration, Outlet Filter recommendation form:
Motor
Capacity
Rated
Voltage
Max. cable length
without filter
(unshielded cable)
Effective cable length
with filter
(unshielded cable）
Outlet
Filter
Model
2.2~4kW
380~480V
40m
95m
JNPH
1AF
5.5kW
380~480V
60m
205m
7.5kW
380~480V
90m
230m
11kW
380~480V
100m
245m
JNPH
2AF
15kW
380~480V
115m
265m
18.5kW
380~480V
125m
285m
22kW
380~480V
130m
305m
JNPH
3AF
30kW
380~480V
140m
315m
45kW
380~480V
145m
330m
55kW
380~480V
155m
335m