Jobsite CT2816 User manual

500KG PETROL MINI DUMPER CT2816
INSTRUCTION MANUAL
DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT WITHOUT READING THIS
MANUAL AND THE SAFETY PRECAUTIONS CONTAINED THROUGHOUT. AND, MOST
IMPORTANTLY, THINK BEFORE YOU ACT AND BE CAREFUL!
Cannon Tools Limited
Address:20 Station Road, Rowley Regis, West Midlands, B65 0JU.UNITED KINGDOM

EC DECLARATION OF CONFORMITY
We CANNON TOOLS LTD
20 Station road, Rowley Regis, West Midlands,B65 0JU.U.K.
Declare that the following machine complies with the appropriate basic safety
and health requirements of the EC Directive based on its design and type, as
brought into circulation by us.
In case of alteration of the machine, not agreed upon by us, this declaration will
lose its validity.
Product description: 500KG PETROL MINI DUMPER
Model: CT2816
Applicable EC Directives:
EC Low Voltage Directive 2006/42/EC
Harmonized standards:
EN 474-1:2006+A4:2013
EN 474-6:2006+A1:2009
20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
Mr. Gurcharan Tony Singh Sanghera
Managing Director
CANNON TOOLS LTD
2021-08-24

1. SPECIFICATIONS
Technical data
Engine : GM170FA, Euro V, 7HP
Engine Type: Single Cylinder, OHV, 4 Strokes, Air Cooling
Displacement : 208 cm3
Rated Power: 3.9KW / 3600 RPM
Fuel Type: 93 # unleaded Gasoline
Fuel Consumption : ≤0.395
Fuel Tank Capacity (L): 3.6
Engine Oil Capacity (L): 0.6
Max Loading Weight: 500kgs
Hopper (L x W x D): 1000 x 680 x 520mm
Cargo box Capacity (dm³): 200 dm³
Tipping Angle: 100°
Walking Speed: 2.88 km/h
Minimum Turning Radius (m): 1.15
Track garage(mm): 520
Minimum Ground Clearance (mm): 100
Climbing Ability (°): 20
Hydraulic Oil Model: 46# Anti-wear Hydraulic Oil
Hydraulic Oil Tank Capacity (L): 15
Sound power level: 101 dB
Sound pressure level: 91 dB
Tipping System: Hydraulic system

Description of the machine
The Mini dumper is built for the construction. Up to the machine there is the
multi-function vessel:
From the factory it goes out in the proper order for to transport material loose as:
soil, manure, leaves, sand, grain and similar. Operating the special lever is
gotten the inclination of the vessel , the lever of closing counter in low to the
left some large case automatically opens, getting unload some transported
material..
The main characteristic of this machine are: to be very simple, strong, and
reliable.
The small dimensions, the particularity of the loom, allow it to operate on every
type of ground guaranteeing safety, stability and reliability in the time. Rapids
verification to the morning will guarantee you a believer and sure companion of
job for the whole day. The operating levers are situated in such a position that
allows good visibility in any position and the operator it has the full control of the
commands.

2. IMPORTANT SAFETY INFORMATION
The following manual is turned to the personnel that has the responsibility of the
correct use of the machines it regards the safety aspects. Recommends
therefore a careful reading, especially of the paragraphs related to the
instructions and to the formalities of use, to possibly preserve him/it in his/her
custody together with the mini-dumper, so that to assure its availability for the
following consultations. The machines provided of devices and safety systems
opportunely studied and tested.
GENERAL INSTRUCTIONS
Safety of employment of the machine is guaranteed only for the
functions listed in these instructions of use.
For operations of extraordinary maintenance and reparation you must be use
only original parts.
All these operations must be performed Out of the machine, in a proper place, in
plain and predisposed.
The whole personnel that can be involved in the use to different title, has to be
educated for a correct use, so that to never jeopardize neither the proper one
or other people's safety.
- Needs that the operator reflects on the possible consequences before
drawing near with the hands particularly
- Don’t make people close around ( distance 2 meters).
- Don’t supply the fuel when the machine is on.
The machine has a considerable metallic mass don’t use when it storms
THUNDER IS CAUSE OF DEATH!
Follow particularly the safety indications:
Use the individual protections as gloves, bonnets masks during the use, for
assembling and maintenance.
Setting particular attention to the parts in movements.
Follow the safety indications brought in the chapter Indications for The Safety.
SAFETY PRESCRIPTION Limits of use, space
The machine has been designed and built for being used in external
environment or in closed environments but airily. The machine is not fit for
the use in underground places, environments with presence of gas, dusts,
and explosive.
The machine has been designed and built for transport of loose materials what:

soil, manure, leaves, sand, stones, gravel, grain and similar, firewood, flowerpots,
baskets, cassettes for fruit, vegetables and other products of the agriculture and
floriculture. The mini-dumper is studied, designed, to transport the material solos
above described.
Be careful driving in reverse.
Always check the ground so that to avoid unexpected obstacles. Operate only in
safety condition.
Don't bring changes to improve the machine performances.
Not reverse the sense of march, if the machine is in movement you can be cause
of accidents.
Driven always to moderate speed, before reversing the march stop you, check
that there are no obstacles and you leave again.
You attentively check the ground on which work: holes, terrestrial yelding, hidden
stones, cables voters, pipelines of the gas or the water etc. can represent a
danger to always operate to checked speed; in case of steps to be overcome,
you always insert some additional thickness between a stair and the other
because they limit the bumps.
You never make descents to the limit of inclination in reverse.
If the machine is used with terrestrial inclination, assure you that the tracks are
oriented in the sense of the inclination and not transversally.
Working on a soft ground, uneven or not leveled it is necessary to set greater
attention to avoid the turnover.
Never overload the machine! You could capsize and provoke serious accidents.
Before climbing with the MACHINE on ramps, check that these are sure of the
suitable course, which is not slippery.
To avoid the superior inclinations to 20°.
Follow the instructions of the manual for a correctly park of the machine.
The gasoline is inflammable. You always extinguish the machine before the
restocking and allow to cool.
Not use the hands for the control of the small oil leakage, neither to hold to use a
cardboard to check on this, complete the possible presence of hydraulic liquid.
If a particular situation brings you to use the machine on the border of a road or
on a slant, worry to check you first the level of the ground and the equilibrium of
the machine, to avoid a possible glide or a turnover.
ATTENTION! EVERY WRONG USE OF THE MACHINE OF THAT EXPECTATION IS
DECLARED AT THE BUILDER IN THE MANUAL PRESENT IT IS CONSIDERED
IMPROPER.
Noise Hazards
● EXCESSIVE NOISE can lead to temporary or permanent loss of hearing.

WEAR an approved hearing protection device to limit noise exposure. As
required by Occupational Health and Safety regulations.
Protective Clothing
● ALWAYS wear approved hearing protection when working in a confined work
space. Protective goggles and a dust mask should be worn when working in a
dusty environment. Protective clothing and footwear may also be desirable when
working with hot mix bitumen.
3. NEW WORK SITE
Transport
The mini-dumper is delivered assembled and functioning, for which it is enough
to unload to load the machine with fit platforms or on a Pallet.
The solidity of the mini-dumper, their form and dimensions, are such to be
guaranteed the portability and the stored in sure way and without damages.
To load and unload with a lift and pallet which suitable to load.
For the machine to go down from the pallet is simple, all it takes is slowly moving
it and with attention. The weight of the mini-dumper is brought on the nameplate;
being a remarkable weight to watch out a lot of in phase of load and unloading.
Assure you that the mean on which transport the machine and the possible
ramps of load, have measures and course adjusted, above all that they have
such a dimension to also allow the passage of the operator. you always Stop the
wheels of the truck with some wedges before loading or to unload the machine.
You fix the ramps to the truck and you conduct the machine on the same with
due caution.
Switch off the engine, removes the ramps and ties the machine to the mean of
transport in sure way.
The machine has stung specific of anchorage and lifting, suitable with adhesive,
therefore tied up labels with straps the loom.
The mini-dumper has these:
- Operator manual
- Engine book
- Funnel for the restocking fuel
We recommend to adopt every caution during the operations of load-unloading
and transport so that to avoid damages and dangers to the people and the car.
The devices of load and transport have to be dimension and conformed in
conformity to the weight to sustain. To lift the car, to use fit ropes and to hook only
him in the suitable points. To follow the safety indications brought in the chapter

Indications for the Safety.
As to leave the machine
The mini-dumper has to be placed in a suitable zone.
Areas of respect and dimensions
The useful space of necessary job to a correct use and to a correct
maintenance is of minimum 5 meters in which the zone of respect is
brought around the car, inside which it is necessary to pay the maximum
attention both for the people and the things, avoiding that there can be obstacles
during the use. Inside the zone of respect it is necessary to pay the maximum
attention to the people and things, avoiding that can be present obstacles to the
passage. To use devices of individual protection as shoes accident prevention
and to handle the periodic cleaning of the floor.
Pre-operation check list
With the commands to hydraulic driving it is EXTREMELY IMPORTANT
that, before beginning the job, the hydraulic oil is heated. During the
phase of heating the operator can verify the correct operation of the
machine or the possible necessity of maintenance.
This manual, the nameplates on the machine furnish the necessary indications
for a correct and sure operation of the car. And' your care to read and to
understand such indications, in how much ignoring you can cause her serious
accidents. Not you leave to the case if there is something that you not
understand. Your distributor will be pleased to give you any necessary
information.
Safety first of all
All the mini-dumper can be dangerous. When are used and correctly
maintained, it is an extremely sure car. If it is wrongly used, it can result
instead dangerous. Both in this manual and on the machine you will find
some instructions, indicator all the potential dangers and as to avoid them. For
any doubt, asks explanations to your retailer or to your responsible forehand. Not
you work with the machine until don't be able to check her/it. Not begin some job
up to that you are not certain of yours and of other people's safety. You could
incur in accidents if you perform some non-formal operations, without doing
before the tests, that must be perform in the free zones away from other people
and on plain ground. Follow the safety prescriptions

Puts in job
Before the mass in work of the machine, especially if it deals with the
first starting or when this is installed in a new place of employment
and' necessary to effect the following verifications and to keep in
mind of the following technical instructions and the following
suggestions:
- Verify the level of the oil;
- Verify the state of use of the tracks;
- Verify the areas of respect and the work areas;
- Verify that the protections have correctly fixed;
- Verify that the indications and the instructions are present on the
machine and easily visible.
Affect a general test of all the commands of the car, to empty to verify its
correctness
Training
Before the use of the machine it is necessary to attentively read
this manual of instructions learning the formalities and the
procedures to operate in safety.
4. REGULATIONS
When using for the first time , the machine doesn't need regulations.
Regulation rubber tracks
Check the tension of the tracks frequently.
An insufficient tension can make to go out the tracks of its own center and it
quickly consumes the wheels engines and the metallic inserts of the track.
An excessive tension increases the resistant strength to the transfer and this can
cause both an excessive wearing out of the bottom wagon is an extra tension of
the track with possible premature breakups.
To prevent possible damages to the tracks in rubber would need to avoid working
more possible in the following situations:
- Cave or pointed rocks.
- Bars or metallic wrecks.
- Edges or edges of metallic objects or cement.
- Fire or other sources of heat.
To eliminate with a rag: gas-oil, hydraulic or fat oil from the surface of the track.
If the machine not used for long time (3 months or more) to store the machine

avoid from the direct light of the sun and rain.
Because of the characteristics of the rubber, to use the machine with
temperatures among -25°C to +55°C.
5. USE
1). OPERATIONS AND COMMANDS
Move of the machine (Joy stick A, B)
Move rectilinear
Push the two levers and the machine start moving
Stop
Leave the levers and machine stopped.
Turning off
Throw back the levers.. Machine move to the back
part ( operator side).
Don’t drive or move the transporter when is switch off.
Maneuvers vessel (D)
Attention!!
When motor is switch off, the lever D
lowers under same weight.
Lift vessel:
Push the lever in ahead to capsize vessel.
Lower vessel:
Throw back the lever to bring the vessel in horizontal
position.
Speed Lever (E)
Decelerate ( )
Push the lever in ahead to lower the turns of the
motor.
Accelerate ( )
Bring back the accelerator lever to increase the
turn of the motor.
During the use of the machine follow the chapter SAFETY LIST.

2). USE OF ENDOTHERMIC MOTOR
Controls before starting
Verify the levels of oil motor and fuel..
For the methods of control, make reference to how much brought in the section
"daily Controls" of this manual.
Starting
Effect the mass in motion of the motor reporting suggestion by the builder of the
motor reading the special manual, of which the machine is equipped.
Turning off
Rotate the Lower part motor Turns for some minutes. This allows the motor to
gradually get cold before the turning off.
Effect the turning off of the motor reporting suggestion by the builder of the
motor reading the special manual, of which the machine is equipped.
3). PREHEATING OF THE MACHINE
As for all the hydraulic systems, it is very important that the hydraulic oil is to
thermal regime before beginning to work.
The necessary time to the preheating can usefully be employed for some simple
operations of control of maintenance. Before effecting height maneuvers load
meticulously follow to the following indications:
- Leave that the motor slowly heats him to low regime of turns for 2-3 minutes.
- Operate the cylinder of lifting of the vessel to heat to allow the filling of the
pipeline.
4) . MACHINE TRANSFER
Rectilinear transfer
1. Move the lever of regulation of the number of turns of the motor in the
desired position.
2. Control the lever:
Rectilinear transfer
Push the lever and the machine go straight on.
STOP
-Move back slowly both the levers up to the intermediary position to brake and
to stop the machine.
-

Transfer reverse
Pull the lever and the machine go back.
Transfer control
1. Move the lever of regulation of the number of turns of the motor in the
desired position.
Check the levers of right transfer and it
damages as it follows.
Curvilinear transfer
Follow the underlying indications:
Turn left
Push the right lever (B) ahead to left turn left
on forward; pull the right lever (B) back to turn
left on backward.
Push the right lever (B) and pull the left lever
(A) together, can turn left faster.
When the hands leave the level, it will returns
to middle position automatically, and the
machine stop turning.
Turn right
Push the right lever (A) ahead to left turn left
on forward; pull the right lever (A) back to
turn left on backward.
Push the right lever (A) and pull the left lever
(B) together, can turn left faster.
When the hands leave the level, it will returns
to middle position automatically, and the
machine stop turning.
Instructions for moves on the ground in
inclination
Lower the regime of turns of the motor when you maneuver in narrow spaces or
climbing over a ditch. On a ground in inclination to possibly move themselves

with the tracks prepared in the sense of the inclination and not transversally. Not
on the wrong side goings never to a slant. You avoid to change the sense of
direction on the slant, this could cause the turnover or side skid of the machine.
Attention to the strong inclinations, the builder of the endothermic motor has
inserted an electric sensor to test the oil level so that to avoid lack of lubrication,
caused by the excessive inclination (max 25°).
5). GENERAL INSTRUCTIONS
Use where the devices of individual protection in demand
Is forbidden to transport people.
Don't put in the large case of the so voluminous loads to be able to hinder
the view from the place of guide.
Don't circulate with the lifted large case.
Don't insist on the joy sticks when the large case is aloft to end run or in low.
Don't brake or to brusquely steer to high speed .
Don't bear the intervention of bystanders in the ray of action of the machine
At the end of every cycle of job, to worry himself/herself/themselves that the
inside of the large case is clean. To lift the alone large case on solid or level
ground.
Maintain on the strong inclinations, the turned loaded large case always
awry.
Every time that he abandons the mini-dumper , to leave him/it in safety, or
rather with lowered large case, out motor and I brake mechanic of inserted
parking.
6). IN ACTION ON THE PLACE OF JOB
Worry during every manoeuvre not to put to risk of it the proper of it other
people's safety.
Avoid every abrupt manoeuvre, particularly on uneven and slippery runs.
Avoid the maneuvers in descent with motor to tall regime of turns.
Avoid to insist when the large case is aloft to end run or in low.
Lift the alone large case when the machine is on terrestrial sure and level.
Always avoid to unload with side inclinations, but to line up the machine in
direction of the inclination.
Progress with prudence in proximity of ditches, excavations, terrestrial yelding
and similar.
Verify every new run and to watch out for the points covered by grass, leaves
or other.
Reduce the speed and load on the most binding runs.
Progress with the turned large case awry when, to load, strong slopes and
descents are faced.

As to stop the machine
You softly leave the levers of transfer and stopped you. The motor must be
allows to turn to empty slowly for about 2 minutes before switch off.
As to leave the machine
You park the machine in a plain zone; don’t leave ever in descent or in the
dangerous zones. The machine is equipped of brake of manual parking, that you
will have to insert for having the certainty that the machine doesn't stir.
7). LIFTING OF THE MACHINE
The missed respect of the following rules can provoke serious
damages, accidents or death.
Not you ever haul the mini-dumper. You use fit means for the transport.
You use cables and appropriate tools for the lifting. The cables of lifting
have to have an enough length to avoid the contact with the machine. To use
organs of lifting suits for to bear the weight of the machine. Do never lift the
machine with personal on board. To use hoist and others you signal to delimit the
zone of load. To always use cables and other devices with superior loads of
breakup to 4T.
PROCEDURES OF LIFTING
On the machine they are anticipated points of hookup but you/he/she can be
lifted through forklift making to climb on her/it on a pallet.
1. Give a sure and strong pallet to sustain the weight of the conveyor.
2. To position in a plain zone and with the empty large case and in lowered
position to make to climb the machine and to center.
3. Stop the motor.
4. Verify that there are not obstacles or people around the machine.
5. Lift the pallet with the machine from the ground of few centimeters and to
verify that is well balanced.
6. Always transport however her to few earth centimeters, not to stir in reckless
way and with the tall load from earth.
LOAD IS UNLOADED OF THE MACHINE
To load and to unload the machine, if possible, on terrestrial leveled and
stable. If unloaded with Ramps, to use a ramp of enough length, width
and thickness to bear the weight of the machine and at the same time
allows the passage of the operator. To avoid glide verified that them no is
slippery.
Never change direction on the ramps of load, to maintain a rectilinear transfer.

LOAD OF THE MACHINE ON THE MEAN OF TRANSPORT
To load and to unload the machine, if don't have a Forklift to load it on a pallet, to
Always use the ramps and to attentively follow the following procedure.
1. To stop the truck in flat ground, fix the wheels before loading the machine.
2. To lower the banks of the truck.
3. To stop in safety the ramps to the truck. The ramps have to form with the
terrestrial an inferior angle to the 15°. The width of the ramps has to be
adjusted to the tracks and they have to foresee the passage of the operator.
4. To position the machine so that is found of forehead and with the parallel
tracks to the ramps of load. Not do use anybody lever, excluded those of
transfer, when the machine is found on the ramps of load. To maintain the
center of gravity of the machine inside the area of the ramps of load.
BLOCK FOR THE TRANSPORT
Switch off the motor to insert the mechanical brake of parking and to assure the
machine to the structure of the truck in opportune way.
8). PARKING MACHINE
At the end of job it is necessary to follow the following procedures every day:
PARKING OF THE MACHINE
To conduct the machine in a flat ground.
1. Reduce the speed of the motor.
2. Always lower the large case not to leave ever lifted before switch off the
motor.
3. Insert the mechanical brake.
4. Switch off the motor.
Under cold conditions
If an anticipated temperatures of strong cold the tracks have to be clean from the
mud and dirt, the machine must be park on the wood tables.

6. MAINTENANCE
The machine doesn't ask for particular operations of maintenance. The technical
solutions and the used components are such to be reduced the interventions of
maintenance. However recommend him to perform a whole operation that you
have the purpose to guarantee the safety, the reliability and the efficiency of the
machine in the time.
During the maintenance
To intervene only on the machine after having park in the zone. In case of
problems type mechanic or electric to turn to an authorized shop. If the machine
is off duty because of breakdowns, maintenance or reparation to signal with
special poster. To always use the devices of individual protection during the
reparation and substitution of the elements of the machine. Interventions on the
motor must be perform only from specialized personnel and authorized. Don't
introduce the hands, the arms or parts of the body in proximity of the zone of
movementation and transmission. Use a suitable device to remove possible
deposits (brushes, wood extremity etc.): not to use only never the hands!
A regular maintenance prolongs the life of the machine, it assures the best
performances and it constitutes a safety important factor.
1). Ordinary and extraordinary maintenance
To clean the air filter after the first 50 hours, if work environments a lot of dust,
cleaning daily.
To verify the presence of possible losses of hydraulic oil.
To verify the tightening of the whole bolts, particularly to daily check the
tension of the tracks.
To replace the oil motor and to perform the other operations foreseen by the
manufacturer of the motor (to see book education of the motor furnished in
enclosure to the manual present)
To perform all the operations of maintenance daily, weekly, fortnightly and
following following you list.
2). MAINTENANCE: daily perform at the end of the job
To eliminate every anomaly that was manifested.
- Clean the interior vessel
- To fatten up all the points of lubrication, with firm motor and large case in
position of rest.
- To attentively verify the state of the tracks.
- To verify if during the job losses of oil or fuel are verified, it is enough to give a
glance to the organs of the machine, not they owe us to be stains that you report

some losses.
3). MAINTENANCE: weekly
Clean the element air filter motor and lowered large case.
4). MAINTENANCE: every 250 hours work
To replace oil motor to see the instructions of the manufacturer of the motor.
Clean the cartridge of the filter fuel.
Replace the element I filter air.
Replace the cartridge filter hydraulic oil..
5). MAINTENANCE every 500 hours work
To replace oil motor to see the instructions of the manufacturer.
Replace hydraulic oil
To always remember that the oil is a special fuel and as such managed to terms
of law. Alternate they are tied up to the type of environment in which the machine
is used, very dusty environments they for example ask for more frequent
interventions of cleaning of the filter air.
6). TABLE OF RECOMMENDED LUBRIFICANTS
Position
Quantity
Frequency
Characteristics
170F ENGINE
Max. 0,6L
250 HRS
(In beginning 20
hrs)
SAE 10W-30
HYDRAULIC
OIL
Capacity 16 L
500 hours
HYDRAULIC OIL LONG DURATION
ISO N° 46
7). CONTROLS AND MAINTENANCE IF NECESSARY
Control tension tracks
a. Screw the die anteriorly set up to that the tension of the track has
not returned to that volute.
b. To conform the tension on both the sides, to move the mini dumper
before and back and to verify again the uniformity of the tension.
c. Verify at the end that both the tracks are tense equally, otherwise to repeat the
operations.
Rubber tracks maintenance
Rubber tracks needs to be changed or revised as follow indications

Height of the outrider
The rubber tracks can be used even if worn, however if excessively consumed,
the tracks can skid and therefore to apply a greater application of power to the
motors of traction. If the remained outrider is inferior or equal to 5 mm is
advisable to replace the track with one new original.
Exposure of the steel ropes
If the steel ropes of a track in rubber are exposed because of an excessive usury
or for damages, to replace the track with one new original.
Cut of the steel ropes of the tracks in rubber.
When a cut is noticed in the steel ropes to immediately replace the track. If the
substitution is not effected keeping on working you/he/she can happen that the
track breaks him completely to the sudden one and this can provoke accidents
and the lock machine if don't have an exchange.
Cracks on the coverage in rubber
If a crack of 30mm is visualized or more than length and 8mm or more than depth,
to immediately mend the rubber. If the steel ropes appear even if the crack is
smaller to immediately mend the track. Otherwise the water that enters the crack
can rust the steel ropes or to provoke the breakup of the track.
Formalities of control of the level hydraulic oil
Always clean the zone around the cork before removing it. Do never overcome
the maximum level of hydraulic oil in the reservoir. Never use the machine when
the level of the oil overcomes the maximum one (full) e/o when inferior to the
least one (to add).
a. To position the machine on plain ground with piston of the completely wide
large case.
b. Verify that the level of the oil is correct.
c. If necessary add oil.
d.Clean and to put again the cork loaded oil B. Per to bring in pressure the
reservoir to make reference to the section "substitution hydraulic oil" of this
manual cap.
FILLING RESERVOIR FUEL
To add the fuel, stop the engine, and remove the fuel tank cap, refuel with funnel.
After refuel, make sure the fuel tank cap have been closed well before start the

engine.
Attention!! To Use only gasoline without lead.
Controls and maintenance every 50 hours
Clean air filter element. To perform the maintenance of the filter of the
engine air extinguished for avoiding damages to the same. Don't clean
the air filter elements with hits or bumps (not to beat it). Do not use air
filter element with damaged parts to prevent damages to the engine. When the
compressed air is used for the cleaning of the elements to wear protections for
the face and respiration, gloves and fit garments for such operations. For the
operations of cleaning of the air filter element to make reference to the manual of
instructions of the engine.
Note: Filter can be clean for 5 times, then you have to change.
Controls and maintenance every 250 hours
Substitution engine Oil or warm parts can cause accidents. Don't bring oil or
warm parts to contact with the skin. To avoid problems with the engine, never
overcome the maximum level of lubricating oil.
An excess of oil of the engine can provoke the breakup of it.
Never start the engine when the level of the oil over the maximum inferior e/o to
the least one. For the operations of substitution of the oil to make reference to
the manual of instructions of the engine.
Cleaning fuel
Attention!! The lost fuel on warm surfaces can provoke a fire.
In addition,for special fuel treatment, Please follow the specifications for
the treatment of residual liquids. For the operations of cleaning of the cup
fuel to make reference to the manual of instructions of the engine.
Substitution air filter
For the operations of substitution air filter element to make reference to the
manual of instructions of the motor.

Substitution of the machine tridge of the filter hydraulic plant
1. The filter is located under the flat machine of load. lift the flatcar and to
extinguish the motor To loosen the cork loaded oil for depressurize the circuit
2. To clean the zone to maintain the dirt to the outside of the body of the filter .
Position under a container suitable to the filter to pick up
3. The possible spillages of oil that can be happened during the operations of
substitution of the tridge filtering. Note: always follow to the norms in force for a
disposal of the exhausted oil and the used filters.
4. Turning counter clockwise incense. To clean the body. Note: The cartridge
filter must have replaced. Reuse is not possible one cartridge already used to
apply some oil on the ring of estate.
5. To insert the new cartridge, to manually press in position, here to tighten with
the special key of a turn.
6. To start the motor and to check the level of the hydraulic oil you again
pressurize the reservoir: After having completely wide the cylinder with the cork
open, to close again the cork of filling of the reservoir.
7. You check if there are losses from the cartridge.
Controls and maintenance every 500 hours
Substitution hydraulic oil
If you contact with oil or warm parts it will provoke burns.
To temperature of exercise, the reservoir of the oil is warm and could be
under pressure. To remove the cork of load oil slowly so that to make to go out
the pressure of the inside of the reservoir.
To remove only the cork of load oil to out motor and when the same is enough
cold to be able him to remove barehanded.
A). Position the machine on plain ground with the cylinder of the completely wide
large case.
B). Insert the sure one against the accidental lowering and to extinguish the
motor.
C). Clean the zone to maintain the dirt to the outside of the reservoir.
D). Loosen the cork of load of the oil for depressurize the reservoir..
Remove the oil from the reservoir using a fit pomp picking up him/it in a fit
container to contain around 20Lt.
Note: to digest oil and filters used according to the normative.
E). To rinse the inside of the reservoir with clean oil..
F). To fill the reservoir with hydraulic oil.
G). To start the motor for a few minutes holding him/it to low regime of turns.