Johannus Vivaldi 370 User manual

User Manual Studio 370
2
Manufacturer Johannus Orgelbouw b.v.
Address Keplerlaan 2
6716 BS EDE
Country The Netherlands
Telephone [phone]
Fax [phone]
E-mail [email protected]m
Website www.johannus.com
Version 1.4
Date August 2018
© 2018 Johannus Orgelbouw b.v.
All rights reserved. Nothing in this publication may be reproduced, stored in a
data file or made public in any form or in any way either electronically,
mechanically by way of photocopying, recording or in any other way without the
prior written permission of Johannus Orgelbouw b.v.

User Manual Studio 370
3
CONTENTS
1SAFETY........................................................................................... 5
1.1 Safety .......................................................................................................... 5
1.2 Symbols on the organ ................................................................................. 6
1.3 Symbols in this manual ............................................................................... 6
1.4 Transport, storage and cleaning................................................................. 7
1.5 Cautions and important notes.................................................................... 8
1.6 Placement ................................................................................................. 10
1.7 Repairs and data ....................................................................................... 10
1.8 Additional precautions ............................................................................. 11
2INSTALLATION ..............................................................................12
2.1 Installation and connection ...................................................................... 12
2.1.1 Installation organ .......................................................................................12
2.1.2 Installation music desk ...............................................................................13
2.1.3 Installation pedal board .............................................................................13
2.2 Switch on .................................................................................................. 14
2.3 Transport and storage .............................................................................. 14
3DESCRIPTION OF THE ORGAN........................................................15
3.1 Overview of the main components .......................................................... 15
3.2 Overview of controls................................................................................. 16
3.3 Connect and switch on the peripherals.................................................... 17
3.4 External connections ................................................................................ 17
4OPERATION ..................................................................................18
4.1 Volume controls........................................................................................ 18
4.2 Expression pedal....................................................................................... 18
4.3 Adaptive Surround Reverb ASR 12 ........................................................... 18
4.4 Intonation styles ....................................................................................... 19
4.5 Stops ......................................................................................................... 19
4.6 Couplers.................................................................................................... 19
4.7 Accessories ............................................................................................... 19
4.8 Pre-programmed memory locations ........................................................ 20
4.9 Capture memory:...................................................................................... 20
4.10 Transposer ................................................................................................ 21
4.11 Johannus Menu ........................................................................................ 21
4.11.1 Datadump...................................................................................................22
4.11.2 Demo Songs................................................................................................22
4.11.3 Display Contrast .........................................................................................23
4.11.4 Expression Pedal.........................................................................................23
4.11.5 Keyboard Config .........................................................................................23
4.11.6 Key Volumes ...............................................................................................24
4.11.7 MIDI Config.................................................................................................26
4.11.8 Reset Procedures........................................................................................27
4.11.9 Reverb Settings...........................................................................................28
4.11.10 Startup Settings ..........................................................................................28
4.11.11 Temperaments ...........................................................................................29
4.11.12 Tuning.........................................................................................................30
4.11.13 Version .......................................................................................................30
5MAINTENANCE, TROUBLESHOOTING AND WARRANTY..................31
5.1 Maintenance............................................................................................. 31
5.1.1 Maintenance of the cabinet .......................................................................31
5.1.2 Maintenance of the manuals .....................................................................31
5.2 Problems................................................................................................... 31

User Manual Studio 370
4
5.3 Warranty................................................................................................... 31
6SPECIFICATIONS............................................................................32
6.1 MIDI Implementation Chart...................................................................... 32
6.2 MIDI Specifications ................................................................................... 33

User Manual Studio 370
5
1SAFETY
1.1 Safety
To reduce the risk of fire or electric shock,
do not expose the organ to liquids, rain or moisture.
Position the organ on a stable, horizontal surface.
Connect the organ to a grounded power socket.
Turn off the organ when it is not in use.
Follow the instructions and precautionary measures in this user manual.
Keep this user manual with the organ.
The organ may only be opened by a technician authorized by Johannus
Orgelbouw B.V. The organ contains static-sensitive components.
The warranty is void if the organ is opened by a non-authorized person.
NOTICE
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings.
Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Unplug this apparatus during lightning storms or when unused for long periods
of time.
13. Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.

User Manual Studio 370
6
1.2 Symbols on the organ
Warning: The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the
product.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
Warning for static-sensitive components. To prevent damage to electronic
parts from static electricity, be sure to discharge any static electricity from
your own body before handling / touching the instrument.
1.3 Symbols in this manual
Caution, Warning or important information
Do not, or forbidden to do
Note

User Manual Studio 370
7
1.4 Transport, storage and cleaning
Pay attention to the following during transport and storage:
Remove the music desk and the pedal board from the organ, before
transport.
Store in an area with 40% to 60% relative humidity.
Do not store in area’s e.g. baths, washrooms, on wet floors, expose to
steam or smoke, salt, humid, rain, moisture, dusty or sandy locations.
Minimum temperature within the storage area: 0°C
Do not expose the Organ to direct sunlight (UV), do not place it near
devices that radiate heat, or otherwise subject to temperature extremes.
Also, do not allow lighting devices that normally are used while their light
source is very close to the Organ (such as a piano light), or powerful
spotlights to shine upon the same area of the Organ for extended periods
of time. Excessive heat can deform or discolor the Organ.
Do not allow rubber, vinyl or similar materials to remain on this Organ
for long periods of time. Such objects can discolor or otherwise harmfully
affect the finish.
Do not paste stickers, decals, or the like to this instrument. Peeling such
matter off the instrument may damage and or discolor the exterior finish.
Do not bend the power cord or place heavy objects on it.
Don’t allow foreign objects or liquids to enter Organ;
Never place containers with liquid on Organ; Do not put anything that
contains water on this Organ. Also, avoid the use of insecticides,
perfumes, alcohol, nail polish, spray cans, etc., near the Organ. Swiftly
wipe away any liquid that spills on the Organ using a dry, soft cloth. Never
use benzene, thinners, alcohol or solvents of any kind, to avoid the
possibility of discoloration and/or deformation.
Unplug the power cord from the outlet before cleaning. Before cleaning
the Organ, turn it off and unplug the power cord from the outlet.
To clean the Organ, use a dry, soft cloth; or one that is slightly dampened.
Try to wipe the entire surface using an equal amount of strength, moving
the cloth along with the grain of the wood. Rubbing too hard in the same
area can damage the finish.
Do not open. Do not disassemble or modify by yourself
Avoid climbing on top of the Organ, or placing heavy objects on it, nor on
top of the keyboard nor pedal board. This can be the cause of
malfunction, such as keys ceasing to produce sound.
Do not bend, drop, strong shock or vibration.
Never strike or apply strong pressure to the display.
Cautions when moving this Organ: Since this product is very heavy, you
must make sure that a sufficient number of people are on hand to help, so
you can lift and move it safely, without causing strain. Make sure to have
a firm grip, to protect yourself from injury and the instrument from
damage. If you need to move the instrument, consult with your retailer,
or Johannus Orgelbouw B.V.

User Manual Studio 370
8
1.5 Cautions and important notes
Indoor use only.
Connect the power cord to an outlet of the correct voltage. The Organ should be
connected to a power supply only of the type described as marked under the keyboard
deck of Organ.
Make sure that the power cord is grounded. Connect mains plug of this model to a
mains socket outlet with a protective earthing connection.
Do not connect or disconnect the power cord with wet hands. Never handle the power
cord or its plugs with wet hands when plugging into, or unplugging from, an outlet.
Turn off the Organ if an abnormality or malfunction occurs. Immediately turn the
Organ off, remove the power cord from the outlet, and request servicing by your
retailer, or Johannus Orgelbouw B.V., when:
•The power-supply cord or the plug has been damaged; or
• If smoke or unusual odor occurs; or
• Objects have fallen into, or liquid has been spilled onto the Organ; or
• The Organ has been exposed to rain (or otherwise has become wet); or
• The Organ does not appear to operate normally or exhibits a marked change in
performance.
Do not use overseas, foreign countries. Before using the Organ in a foreign country,
consult with your retailer, or Johannus Orgelbouw B.V.
Adults must provide supervision in places where children are present. When using the
Organ in locations where children are present, be careful so no mishandling of the Organ
can take place. An adult should always be on hand to provide supervision and guidance.
Do not connect this Organ to same electrical outlet that is being used by an electrical
appliance that is controlled by an inverter or a motor (such as a refrigerator, washing
machine, microwave oven, or air conditioner). Depending on the way in which the
electrical appliance is used, power supply noise may cause this Organ to malfunction or
may produce audible noise. If it is not practical to use a separate electrical outlet,
connect a power supply noise filter between this Organ and the electrical outlet.
Do not share an outlet with an unreasonable number of other devices. Do not force
the Organ’s power-supply cord to share an outlet with an unreasonable number of other
devices. Be especially careful when using extension cords—the total power used by all
devices you have connected to the extension cord’s outlet must never exceed the power
rating (watts/amperes) for the extension cord. Excessive loads can cause the insulation
on the cord to heat up and eventually melt through - therefore always completely
unwind an extension cord.
To prevent malfunction and equipment failure, always make sure to turn off the
power on all your equipment before you make any connections.
Although the LCD and LEDs are switched off when the Organ is turned off, this does not
mean that the Organ has been completely disconnected from the source of power. If

User Manual Studio 370
9
you need to turn off the power completely, first turn off the Organ’s switch, then unplug
the power cord from the power outlet. For this reason, the outlet into which you choose
to connect the power cord’s plug should be one that is within easy reach and readily
accessible.
If there is a possibility of lightning strike, disconnect the power cord from the outlet.
Whenever you suspect the possibility of lightning in your area, pull the plug on
the power cord out of the outlet.
Periodically clean the power cord’s plug. At regular intervals, you should unplug
the power plug and clean it by using a dry cloth to wipe all dust and other
accumulations away from its prongs. Also, disconnect the power plug from
the power outlet whenever the Organ is to remain unused for an extended period of
time. Any accumulation of dust between the power plug and the power outlet can
result in poor insulation and lead to fire.
The settings you were editing will be lost when the Organ is turned off. If you want to
keep your settings, you must save your settings before turning the Organ off.
Place in a well ventilated location. The Organ should be located so that its location or
position does not interfere with its proper ventilation.
Manage cables for safety. Try to prevent cords and cables from becoming entangled.
Also, all cords and cables should be placed so they are out of the reach of children.
Grasp the plug when connecting or disconnecting the power cord. Always grasp only
the plug on the power-supply cord when plugging into, or unplugging from, an outlet.
Precautions concerning use of bench. When using the bench, please observe the
following points:
• Do not allow two or more persons to sit on the bench.
• Do not adjust the height while sitting on the bench.
Do not remove the speaker grille and speaker. Do not remove the speaker grille and
speaker by any means. Speaker not user replaceable. Shock hazardous voltages
and currents are present inside the enclosure.
Disconnecting power from AC mains. To completely disconnect this apparatus
from the AC mains, disconnect the power supply cord plug from the AC receptacle.
The power supply cord and/or main power switch must be accessible. The mains plug
of the power supply cord shall remain readily accessible. Or, the power switch must be
accessible. The main power switch is the main power disconnect device for this Organ.
Therefore, the power switch shall be readily accessible.

User Manual Studio 370
10
1.6 Placement
Using the Organ near power amplifiers (or other equipment containing large power
transformers) may induce hum. To alleviate the problem, change the orientation of
this Organ; or move it farther away from the source of interference.
This device may interfere with radio and television reception. Do not use this device in
the vicinity of such receivers.
Noise may be produced if wireless communications devices, such as cell phones, are
operated in the vicinity of this Organ. Such noise could occur when receiving or
initiating a call, or while conversing. Should you experience such problems, you should
relocate such wireless devices so they are at a greater distance from this Organ, or
switch them off.
Do not expose the Organ to direct sunlight, place it near devices that radiate heat, or
otherwise subject it to temperature extremes. Also, do not allow lighting devices that
normally are used while their light source is very close to the Organ (such as a piano
light), or powerful spotlights to shine upon the same area of the Organ for extended
periods of time. Excessive heat can deform or discolor the Organ.
Do not allow rubber, vinyl, or similar materials to remain on this Organ for long
periods of time. Such objects can discolor or otherwise harmfully affect the finish.
Do not allow objects to remain on top of the keyboard or pedal board. This can be
the cause of malfunction, such as keys ceasing to produce sound.
Do not paste stickers, decals, or the like to this instrument. Peeling such matter off
the instrument may damage the exterior finish.
Do not put anything that contains water on this Organ. Also, avoid the use of
insecticides, perfumes, alcohol, nail polish, spray cans, etc., near the Organ. Swiftly
wipe away any liquid that spills on the Organ using a dry, soft cloth.
1.7 Repairs and data
Please be aware that all data contained in the Organ’s memory may be lost when the
Organ is sent for repairs. Important data should always be stored (see ‘Datadump’
chapter 4.11.1), or written down on paper (when possible).
During repairs, due care is taken to avoid the loss of data. However, in certain cases
(such as when circuitry related to memory itself is out of order), we regret that it may
not be possible to restore the data, and Johannus Orgelbouw B.V. assumes no liability
concerning such loss of data.

User Manual Studio 370
11
1.8 Additional precautions
Please be aware that the contents of memory can be irretrievably lost as a result
of a malfunction, or the improper operation of the Organ. To protect yourself
against the risk of losing important data, we recommend that you periodically
write down important setting data, see chapter ‘Datadump’ 4.11.1, or on paper
(when possible).
Unfortunately, it may be impossible to restore the contents of data that was
stored in the Organ’s memory once it has been lost. Johannus Orgelbouw B.V.
assumes no liability concerning such loss of data.
Use a reasonable amount of care when using the Organ’s buttons, sliders, or
other controls; and when using its jacks and connectors. Rough handling can
lead to malfunctions.
Never strike or apply strong pressure to the display.
A small amount of heat will radiate from the Organ during normal operation.
To prevent possible hearing damage, do not listen at high volume levels for long
periods. This Organ, either alone or in combination with an amplifier and
headphones or speakers, may be capable of producing sound levels that could
cause permanent hearing loss. Do not operate for a long period of time at a high
volume level, or at a level that is uncomfortable. If you experience any hearing
loss or ringing in the ears, you should immediately stop using the Organ, and
consult an audiologist.
To avoid disturbing others nearby, try to keep the Organ’s volume at reasonable
levels. You may prefer to use headphones, so you do not need to be concerned
about those around you.
When you need to transport the Organ, pack it in shock-absorbent material.
Transporting the Organ without doing so can cause it to become scratched or
damaged, and could lead to malfunction.
Do not apply undue force to the music stand while it is in use.
Some connection cables contain resistors. Do not use cables that incorporate
resistors for connecting to this Organ. The use of such cables can cause the
sound level to be extremely low, or impossible to hear. For information on cable
specifications, contact the manufacturer of the cable.
Due to the structural design of this instrument, small pets or other animals could
end up getting trapped inside it. If such a situation is encountered, you must
immediately turn off the Organ and disconnect the power cord from the outlet.
You should then consult with the retailer from whom the instrument was
purchased, or contact Johannus Orgelbouw B.V.
The explanations in this manual include illustrations that depict what should
typically be shown by the display.
Note, however, that your Organ may incorporate a newer, enhanced version of
the system (e.g., includes newer sounds), so what you actually see in the display
may not always match what appears in the manual.

User Manual Studio 370
12
2INSTALLATION
2.1 Installation and connection
2.1.1 Installation organ
1. Position the organ on a stable, horizontal surface.
2. Install the music desk (A) on top of the organ, see § 2.1.2.
3. Install the pedal board (D), see § 2.1.3.
4. Place the organ bench (C) over the pedal.
5. Make sure the voltage of the organ matches the voltage of the mains. See
the serial plate (B).
6. Connect the organ to a grounded power socket.
A
C
D
B

User Manual Studio 370
13
2.1.2 Installation music desk
1. Turn countersunk brass screws (A) into music desk slat (B) by hand till screws
stick out 2 mm (C).
2. Place music desk at the right position, with screw points into the pre-drilled
holes (D).
3. Tight music desk with screw driver. Electric screw driver is not
recommended.
4. Remove green protection foils (E) from plexiglas part of the music desk.
2.1.3 Installation pedal board
1. Shift pedal board against black
pedal front cover (A). Pedal bolts
(B) will stick out 5 mm.
2. For security reasons mount
pedal board to organ with wing
nuts (C).

User Manual Studio 370
14
2.2 Switch on
Switch on the organ with the on/off piston at
the right, next to the manuals. Wait several
seconds. Starting the control functions and the
settings will take some time.
The lamps of the 0 piston and the as standard
set functions light up. The settings appear on
the display.
2.3 Transport and storage
Pay attention to the following during transport and storage:
1. Remove the music desk and the pedal board from the organ.
2. Relative humidity within the storage area: 40 to 60%.
Initializing...
Please wait
Studio Mem: 1
Tr: 0/440

User Manual Studio 370
15
3DESCRIPTION OF THE ORGAN
3.1 Overview of the main components
AMusic desk
BLoudspeakers
COrgan bench
DExpression pedal
EPedal board
A
C
B
D
E

User Manual Studio 370
16
3.2 Overview of controls
A MIDI
B Pedal stops
C Swell stops
D Great stops
E Choir stops
F Volume control Organ
G Volume control Cathedral
H Headphones connection
I SET (programming capture system)
J Capture memory locations (1 to 8)
K CH: Chorus
LPre-programmed memory locations
MRO: Reeds Off
N Intonation styles (ROM,SYM,BAR,HIS)
O TRANS.: Transposer
P - and + pistons
Q ENTER
R MENU
S 0: Recall / Reset
T ORCHESTRAL SOUNDS:
- PANFL.: Pan flute
- TRUMP.: Trumpet
MB: Manual Bass
U On/Off (mains switch)
V Manual Choir
W Manual Great
X Manual Swell
Y Display

User Manual Studio 370
17
3.3 Connect and switch on the peripherals
You can connect accessories (for example, a MIDI device) to the organ.
1. Switch off the organ and the accessory.
2. Connect the accessory to the organ.
3. Switch on the accessory.
4. Switch on the organ
3.4 External connections
The external connections are on the left under the console.
MIDI IN: An input for receiving MIDI codes from other devices.
MIDI MOD: A programmable MIDI output for connecting a sound module or
expander, for example.
MIDI SEQ: A non-programmable MIDI output for connecting a sequencer or PC
(with the optional Johannus Intonat program), for example.
AUX IN: A stereo audio input for playing the sound of an external device through
the amplifiers of the organ. For example, an expander connected to the organ
through the MIDI MOD can be played through the instrument's loudspeakers.
AUX OUT: A stereo audio output for connecting an external device (amplifier or
recording device, for example).
Phones:
The phones connection is at the left next to the manuals.
This connection for a (stereo) headphone is suited for a headphone with an
impedance of 30 Ωor more (see headphone specifications).
Follow the instructions provided in the documentation for the accessory.
When the headphone is used, the loudspeakers of the organ are switched off
automatically.

User Manual Studio 370
18
4OPERATION
4.1 Volume controls
Organ: You can adjust the volume of the organ with the ORGAN volume control.
Cathedral: The reverb volume can be adjusted smoothly with the CATHEDRAL
volume control.
4.2 Expression pedal
With the expression pedal the volume of the Swell or the entire organ can be
changed. By default the expression pedal
functions for the Swell only. This is indicated on
the display with Exp:Sw.
Using the Johannus Menu the expression pedal can also be set as a general swell
for the entire organ, see § 4.11.4. If the
expression pedal is set as general swell, this is
indicated on the display with Exp:GS.
Using the expression pedal also changes the timbre of the Swell stops. By this the
effect of a swell box of a pipe organ is simulated.
4.3 Adaptive Surround Reverb ASR 12
The ASR 12 reverb system produces a digital acoustic effect. This effect provides a
spatial reproduction of the organ sound that can be adjusted continuously.
Turn the volume control CATHEDRAL to adjust the reverb volume.
The reverb length can be set using the Johannus Menu. See § 4.11.9. The length
can be set for each intonation style.
The following 12 reverb types can be selected for each intonation style in the
Johannus Menu:
Abbey Church
Basilica
City Cathedral
Concert Hall
Hill Church
Marble Church
Marble Room
Music Room
Palace Hall
Royal Auditorium
Town Church
Village Chapel
Studio Mem: 1
Tr: 0/440 Exp:Sw
Studio Mem: 1
Tr: 0/440 Exp:GS

User Manual Studio 370
19
See § 4.11.9 for assigning a reverb to an intonation style.
4.4 Intonation styles
The organ has four intonation styles:
Romantic (ROM), Symphonic (SYM), Baroque (BAR) en Historic (HIS).
Select an intonation style by pressing the ROM, SYM, BAR or HIS piston.
4.5 Stops
The stops are activated via rocker switches, pre-programmed memory locations or
capture memory locations. The lamp in the rocker switch lights when the
associated stop is active. The stops are divided into three groups:
Pedal: Activates the stops associated with the Pedal.
Choir: Activates the stops associated with the Choir.
Great: Activates the stops associated with the Great.
Swell: Activates the stops associated with the Swell.
4.6 Couplers
Choir Manual coupler:
SWELL - CHOIR: Fully couples all keys of the Swell to the Choir.
Great Manual coupler:
CHOIR - GREAT: Fully couples all keys of the Choir to the Great.
SWELL - GREAT: Fully couples all keys of the Swell to the Great.
Pedal couplers:
CHOIR - PEDAL: Fully couples all keys of the Choir to the Pedal.
GREAT - PEDAL: Fully couples all keys of the Great to the Pedal.
SWELL - PEDAL: Fully couples all keys of the Swell to the Pedal.
Manual Bass:
Couples the Pedal monophonic to the Great. Only the lowest key that is played on
the Great is coupled from the Pedal to the Great.
Activate the Manual Bass with the MANUAL BASS stop.
If only the lowest key of a chord is released, the pedal key activated by the
Manual Bass function is dropped until a new lowest key is played. This should
prevent the bass keys from "jumping".
4.7 Accessories
Chorus (CH):
Chorus is a function for lightly detuning the organ stops to give it a broader and
livelier sound. Use the CH piston to activate the Chorus.
Reeds Off (RO):
Reeds off is a function to switch off all reed stops simultaneously. As long as this
piston is pressed, no reed stops can be activated. When this function is switched
off, the reed stops that were on are activated again. Use the RO piston to activate
the Reeds Off function.

User Manual Studio 370
20
Pan flute (PANFL.), Trumpet (TRUMP.):
Use the PANFL. piston and/or TRUMP. piston to activate these orchestral sounds.
Assignment of Pan flute and Trumpet sounds to a specific manual
Press the SET piston and PANFL piston simultaneously to activate the assignment
option for the Pan flute orchestral sound. After that, press a key on one of the 3
manuals (Choir, Great, or Swell) to assign the Pan flute to a specific manual.
During this action, the display shows the assigned instrument. The Trumpet can
be assigned in the same way: In this case press the SET and the TRUMP. pistons
simultaneously and thereafter a random key on one of the 3 manuals.
Recall / Reset function (0):
The 0 piston cancels registration in two ways:
1. A short press on the 0 piston: Only the last change is cancelled.
2. A long press on the 0 piston: All registrations are cancelled.
4.8 Pre-programmed memory locations
Pre-programmed memory locations are available by operating pistons PP to T and
PL. These seven memory locations have factory settings (presets) appropriate for
the quiet pianissimo to the loud tutti and the classic plenum.
Calling up a pre-programmed memory location:
Press a pre-programmed memory location (PP-T or PL). The active stops light up.
Programming a pre-programmed memory location:
1. Select the desired stops.
2. Press the SET piston. Hold in the piston.
3. Press the desired pre-programmed memory location (PP-T or PL).
4. Release the SET piston.
4.9 Capture memory:
Through use of the capture memory, a registration can be made active with just
one piston.
The capture memory consists of 75 levels. These levels can be seen on the display
(Mem:… ). Each level has eight memory locations (pistons 1-8). The 600 capture
memory locations are not pre-programmed and can be programmed by the
musician.
The current setting of the pre-programmed memory location will be lost.
Although it is possible to store any registration under a piston of a pre-
programmed memory location it is advisable to select a registration matching the
text of the piston.