JohnsonSuisse Barossa Slider 1200 User manual

INSTALLATION GUIDE
barossa
slider shower screen
• Immediately on receipt inspect the product for transit damage, missing packs/parts or manufacturing faults.
• Damage reported later cannot be accepted.
• Please handle the product with care avoiding knocks and shock loading to all sides and edges of glass.
• Damaged glass or missing parts will not be replaced under warranty if the installation process has begun.
• SAFETY GLASS CANNOT BE REWORKED, IF BROKEN IT HAS TO BE REPLACED
• Please read these instructions carefully before you start installation. Special care should be taken when drilling walls
to avoid hidden pipes or electrical cables.
• Securing into a stud or timber brace is highly recommended, if unable to do so, other secure means of xing must
then be considered.
This product is heavy and awkward to handle.
Two-person installation is recommended.
TOOLS REQUIRED
Model* Door + Fixed Panel Set Return Panel Set
Barossa Slider
1200
SSBA34CHCLS
Alcove size 1155-1175mm
Return size 1170-1195mm
-
Barossa Slider
1500
SSBA37CHCLS
Alcove size 1435-1455mm
Return size 1450-1475mm
-
Barossa Slider
900 -SSBA26CHCLR
Actual size 860-885mm
These installation guidelines are for to the following shower screens:
IMPORTANT PRE-INSTALLATION NOTE:
1
* Screen and panel codes shown are for Chrome nish option.
Matte Black nish option is also available.

INSTALLATION GUIDE
barossa
slider shower screen
ASSEMBLY COMPONENTS
2
1
8
234
6
7
5
10
11
12
13
14
15
16
17
18
19
9
20
22 21
23
2
1. 2 x Wall plugs
2. 1 x Side panel
3. 2 x Buffer strips
4. 1 x Door Panel
5. 1 x Vertical seal
6. 1 x Fixed glass front panel
7. 1 x Rail
8. 1 x Drip rail
9. 1 x End block (R)
10. 1 x Sliding block (R)
11. 8 x 6mm wall plugs
12. 8 x 4mm steel washers
13. 8 x 3.5x35 SS screws
14. 1 x Handle set
15. 1 x Rail bracket side panel parts
16. 1 x Rail bracket
17. 2 x Roller sets
18. 2 x Lock-in knob sets
19. 2 x Rail support sets
20. 4 x Setting blocks
21. 8 x 3.9x8 SS screws
22. 8 x Screw caps
23. 1 x Screen block
COMPONENT LIST

INSTALLATION GUIDE
barossa
slider shower screen
3
1170-1195mm
1450-1475mm
860-885mm
Before starting:
Ensure oor area for installation is completely level.
Walls must be plumb to within 5mm over the height of the screen.
Check-measure that the screen size shown on the packaging suits the intended installation area.
STEP 1
Ø6mm
ST3.5x35
1.1 Adjust wall jambs [1] to ensure they are plumb and within the
minimum/maximum size range, measuring to the outside of the
wall jamb.
1.2 Mark holes on the wall through the holes on the wall prole.
1.3 Drill holes in wall using a masonry bit, then carefully tap-in the
wall plugs [11]. Plugs supplied are standard masonry type; use
other appropriate xings if plugs supplied are not suitable for
your wall type.
1.4 Screw wall jambs to walls using [12,13] ensuring the jambs are
plumb.
1.1
1.2
1.3
1.4

INSTALLATION GUIDE
barossa
slider shower screen
4
STEP 2
2.1 Insert the side panel [2] and xed front panel [6] into the wall jambs.
2.2 Glass must be set on glass setting blocks [20] provided to prevent shock loading. Trim setting block to thick-
ness of glass once set in place.
To prevent breakage glass must not come into contact with hard surfaces.
2.1
2.2
2.1

INSTALLATION GUIDE
barossa
slider shower screen
5
Note: these screws
must face the inside of
the shower
STEP 3
3.1 Install rail bracket [15,16] to return panel.
3.2 Insert rail [7] into rail bracket and connect rail to front xed panel using the rail support sets [19].
3.3 Adjust side panel to be parallel wall or edge of base, if necessary, adjust the xed panel to ensure that
the rail is inserted in bracket beyond the grub screw. Tighten grub screw on bracket to x rail in place.
Rail Glass
M8 button
Steel
washer
Plastic
washer
Side panel
Fixed glass
front panel
Side panel
Fixed glass
front panel
Rail bracket
Screw
3.1 3.2
3.3
Ensure a plastic glass protector is used between all metal parts and glass

INSTALLATION GUIDE
barossa
slider shower screen
6
STEP 4
4.1 Install the roller sets [17] to door panel [4]. Rollers should be on the outside of the door.
4.2 Hang the door on the rail from inside of the shower.
4.3 Carefully slide the door toward the side panel and check the gap between door & side panel is even; ad-
just if necessary using o󰀨set in rollers or adjustment from the rail support.
4.4 Install the sliding block [10] to the front xed panel and tighten lock-in screw.
4.5 Install the lock-in knob set [18] into holes in door panel with the chrome knob on the outside of door.
Roller
4.3
Sliding
block
M8
button
chrome knob
Chrome
knob
M8
button
4.1
4.2
4.3
4.5
4.4
Ensure a plastic glass protector is used between all metal parts and glass

INSTALLATION GUIDE
barossa
slider shower screen
STEP 5
5.1 On the inside of the shower, drill 3.2mm holes through the xed panel prole and wall jamb; then the return panel
prole and wall jamb. Screw together using screws [21], t the screw caps to the expose screw head [22].
5.2 Install the bu󰀨er strips [3] onto the door panel.
5.3 Install the vertical seal [5] onto the xed panel.
5.4 Apply silicone to the underside of the drip rail [8] and end block [9], then insert drip rail into sliding block, with the
end block connecting the drip rail to the side panel.
5.5 Install the handle set [14], with the locking screws on the inside of the shower.
Drill holes from the
inside of the shower
wa
screw
Screw
Washer
Apply
silicone
5.1
5.2
5.3
5.4
5.5
Ensure a plastic glass protector is used between all metal parts and glass
7

INSTALLATION GUIDE
barossa
slider shower screen
Apply bathroom quality silicone sealant around all external joints of the shower screen.
Sealant is not used on the inside of the screen as in time water may build up within the wall jamb and then leak out of the shower
area. The screen is designed to allow water to drain within the shower area.
ALLOW 24 HOURS BEFORE USING THE SHOWER
STEP 6
CARE INSTRUCTIONS
This shower screen has been treated with EnduroShield® easy-to-clean glass surface treatment. Please follow the care
instructions a󰀩xed to the door panel to ensure that your treatment is long-lasting.
After use, your shower should be cleaned with mild detergent and water. This is particularly important in hard water areas
where insoluble lime salts may be deposited and allowed to build up.
Cleaners of a abrasive/gritty nature should not be used. Care should be taken to avoid contact with strong chemicals such as
organic solvents and strippers. Glass cleaners can be used but with caution. If in doubt please contact the manufacturer of
the cleaner in question.
Please keep these instructions for aftercare and customer service details.
Bathroom Products Australia Pty Ltd
PO Box 728 Botany NSW 1455
Tel: [phone]
Fax: [phone]
www.johnsonsuisse.com.au
8
Apply bathroom quality silicone sealant around all
external joints of the shower screen.
Sealant is not used on the inside of the screen as in
time water may build up within the wall jamb and then
leak out of the shower area. The screen is designed
to allow water to drain within the shower area.
ALLOW 24 HOURS BEFORE USING THE SHOWER