JohnsonSuisse Gemelli JBTG2150 User manual

INSTALLATION GUIDE
Gemelli
Freestanding Bath
JBTG2150
JBTG2170
Australian
Registered Design
580
1240/1040 590
450
115
1700/1500 1480/1300
1020/900
780/710
750
710
480
660
80
200
20
15
260
20
P.1

INSTALLATION
Installation must be carried out by a licensed plumber in compliance with the Plumbing Code of Australia..
Check local and national building regulations before installation to ensure the below methods comply with
the relevant codes.
Tools required for installation: Silicone Gun, Spirit Level, Tape Measure, Pencil, Adjustable Spanner.
1. Inspect bath thoroughly before installation. Claims for defects and/or damage must be made before
installation commences.
2. Place bath in intended position and mark out position on the finished floor.
3. Check level by placing spirit level across the width and length of bath, then adjust feet to suit.
Ensure the bath is fully supported on all feet.
4. Connect waste to drainage using approved methods [Fig. 1 or Fig. 2].
5. Apply silicone to underside of feet to secure to place.
6. Conduct final water test on bath to ensure water drains to waste.
7. Allow silicone 24 hours (minimum) curing time.
Note: Hot water applied to this product must not exceed 55o
C.
Floor Waste and trap are not included.
Plug & Waste
Plug & Waste Extension
Smart Waste rubber sealSmart Waste
o
100 mm 90 Elbow
Figure 1
INSTALLATION GUIDE
Gemelli
Freestanding Bath
P.2

Your Gemelli Freestanding Bath is manufactured using Lucite®
sanitary grade acrylic.
To maintain your bath’s high glossfinish, please follow these simple instructions:
General Cleaning
Wipe acrylic with a mild soap or detergent and lukewarm water solution, using a clean microfiber cloth. Rinse well,
wring out microfiber cloth and wipe again to remove moisture and streaking.
Deep Cleaning
Work into surface a thin, even coat of Ultra Gloss Bathroom Cleaner & Polish, using a soft cotton towel. Lightly
buff off excess residue with a dry portion of your towel.
After polishing, wipe with a clean damp microfiber cloth to completely remove excess residue and remove any
electrostatic charges which may attract dust particles.
Deep scratches can be removed with fine grit wet/dry sand paper and buffed to a shine using Ultra Gloss.
Caution
Window cleaning fluids, scouring compounds, harsh chemical cleaners, gritty cloths, leaded or ethyl gasoline or strong
solvents such as alcohol, acetone, etc. must not be used.
Do not place hot objects such as hair straighteners and curlers directly onto the surface.
Figure 2
Flexible Connector
Waste Trap
Waste Pipe
Plug & Waste
INSTALLATION and CARE GUIDE
Gemelli
Freestanding Bath
600 40mm pop-down
PW8 or PW8B
flexible connector
waste with 600mm
P.3

FOR FURTHER INFORMATION PLEASE
www.johnsonsuisse.com.au
CONTACT YOUR NEAREST MARBLETREND
OFFICE:
HEAD OFFICE (SYDNEY)
2/97 Banksia St, Botany, NSW 2019
T 1300 717 717 F 1300 746 480
MELBOURNE
31 Koornang Rd, Scoresby, VIC 3179
T 1300 717 717 F 1800 225 315
BRISBANE
1/477 Newman Rd, Geebung, QLD 4034
T 1300 717 717 F 1300 746 480
PERTH
27 Harris Rd, Malaga, WA 6090
T 1300 717 717 F 1800 746 480
ADELAIDE
Rep: Terry Hayes
T 0499 221 201 F 1800 225 315
HOBART
Rep: Bob Moore
T 0428 223 116 F 1800 225 315
DUBBO
Rogers Agencies
6 Richard Ryan Pl, Dubbo NSW 2830
T 02 6882 2733 F 02 6882 2169
www.johnsonsuisse.com.au
WARRANTY INFORMATION
This warranty is provided by:
Bathroom Products Australia Pty Ltd
(ABN 87 079 297 617)
2/97 Banksia St
Botany NSW 2019
P 1300 717 717
F 1300 746 480
E [email protected]
Visit www.johnsonsuisse.com.au to view full warranty terms.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for the major failure and for compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
R0.0
GENERAL INFORMATION
Gemelli
Freestanding Bath
P.4