Judge JEA32 User manual

Knife SharpenerKnife Sharpener Knife Sharpener
Knife Sharpener
Instruction Manual
Model No. JEA32
PLEASE READ THIS INSTRUCTION MANUAL CAREFULLY BEFORE USE AND
RETAIN FOR LATER REFERENCE.
UNPACK YOUR KNIFE SHARPENER CAREFULLY AND REMOVE TEMPORARY
PACKING PIECES, LABELS AND STICKERS.
Judge 2 Year Domestic Electrical Guarantee
The Judge Guarantee covers the product to be free of defects
in materials and workmanship for a period of TWO YEARS
from the date of original retail purchase. During this period,
JUDGE will, at their option, repair or replace defective parts of
the product, or replace the product, providing the Use Care and
Safety Advice have been followed.
The Guarantee does not cover damage, defect or failure
caused by or resulting from accidents, external damage,
alteration, modification, abuse, misuse or misapplication.
The Guarantee does not cover any damage caused by taking
the appliance apart yourself, or attempting to repair the
appliance yourself.
THE PRODUCT IS INTENDED FOR DOMESTIC USE ONLY.
Please keep your Purchase Receipt and contact us directly if
you encounter any problems with your product.
HORWOOD SHALL NOT BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF
THIS PRODUCT (INCLUDING COLOUR FADING, SCRATCHES
OR ACCUMULATED DIRT) WITHOUT FOLLOWING THE USE,
CARE & SAFETY INSTRUCTIONS.
Note: Due to the introduction of improvements from time to time,
illustrated and described in this publication.
Errors and Omissions Excepted.
JUDGE CUSTOMER SERVICES, HORWOOD,
AVONMOUTH WAY,
BRISTOL,
BS11 9HX, GREAT BRITAIN
[email protected] www.judgecookware.co.uk
Tel: [phone]
CORRECT DISPOSAL OF THIS PRODUCT
This marking indicates that this product should not be disposed with other household
wastes throughout the EU. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse
of material resources. To return your used device, please use the return and collection
systems or contact the retailer where the product was purchased. They can take this
product for environmental safe recycling.
FOR DOMESTIC USE ONLY
Specification
Name Model No. Rated Voltage Rated Frequency Rated Power
Judge Knife Sharpener JEA32 220 - 240V 50Hz 60W
Cautions
Before use, check that your mains power supply corresponds to the voltage shown•
in this manual (also shown on the rating plate of the appliance, located on its
underside).
This appliance is not intended for use by persons (including children) with reduced
•
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Always keep the appliance out of the reach of children.
•
Do not connect the plug into the socket, or use the appliance, if your hands or the•
appliance are wet.
Unplug the appliance when it is not in use.
•
Never leave the unit unattended while it is operating.•
The mains lead should be positioned so as not to cause an obstruction or to•
overhang the edge of the surface, where it could accidentally be snagged or
pulled. Wrap excess cable around the cable store located on the underside of the
appliance.
Do not use the appliance outdoors.
•
Do not place the appliance close to a heat source.•
Ensure that the mains lead is not near any hot surface.•
Pull the plug (do not pull mains lead) to disconnect from mains socket.•
Do not pull the mains lead to move the appliance.•
Do not use the appliance with any accessories other than those supplied.•
The appliance should be used only as instructed and for the purpose for which it•
was intended; there is potential for injury or damage from misuse.
Do not use any lubricants or oils, either for maintenance or in the grinding process.•
Do not attempt to use more than one grinding slot at a time.•
Do not switch on the appliance with a blade already in a grinding slot.•
After sharpening, blades will be very sharp. Take care when handling.•
The screwdriver restorer is suitable only for flat-bladed screwdrivers that will•
readily fit into the screwdriver slot. Do not attempt to use with other types of
screwdriver.
Do not use any cleaning fluids or abrasives to clean the appliance.
•
Do not switch on or attempt to operate the appliance if it appears to be faulty in•
any way - contact Judge Customer Services at the address given in the Warranty
section.
Never attempt to make any repair to the appliance yourself - contact Judge
•
Customer Services at the address given in the Warranty section.
Do not immerse the appliance in water.
•
Should the appliance accidentally fall into water, unplug immediately and do•
not use; contact Judge Customer Services at the address given in the Warranty
section.
Please keep your purchase receipt.
•
Page 5 Page 6
Version: 002

Knife SharpenerKnife Sharpener Knife Sharpener
Identifying the parts
(with
Part Numbers
for customer replaceable items)
LH knife slot (coarse grind)1.
RH knife slot (coarse grind)2.
LH knife slot (fine grind)3.
RH knife slot (fine grind)4.
Scissors slot5.
Screwdriver slot (see inset)6.
ON/OFF switch7.
Waste drawer (coarse grind)8.
(JEA32DC)
Waste drawer (fine grind)9.
(JEA32DF)
Mains plug10.
Mains lead11.
blade and the right hand slots 2and 4are used to sharpen the left hand side of
the knife blade.
Until you are familiar and comfortable with using the Knife Sharpener, it is
•
recommended that you practise the appropriate sharpening technique described
below with the Knife Sharpener switched off. After this, start the Knife Sharpener
as described in the following steps 1 and 2, then proceed as described under Knife
Sharpening, Scissor Sharpening, or Screwdriver Restoring, as required.
Insert the Mains Plug1. 10 into a mains socket and switch on at the socket.
Set the ON/OFF Switch2. 3to the ON position; the switch will illuminate and the
grinding wheels will revolve.
Knife Sharpening
Knife sharpening is performed in two stages - a coarse grind, followed by a fine •
grind, alternating between one side of the knife, then the other, and repeating
three times, at each stage. The grinding technique, used at both stages, is
described in steps A and B. The sequence to follow is detailed in steps 1 to 7.
With the sharpener switched on, insert the knife blade into one of the knife slots,A.
keeping the blade sufficiently high in the slot
to avoid contact with the grinding wheel and
ensuring that the cutting edge of the blade is
pushed fully into the slot.
Note: the diagrams show the knife in the right
•
hand Coarse Grind Knife Slot 2.
In a single motion, move the knife bladeB.
downwards into the slot, until you feel
the blade is in good contact with the
spinning grinding wheel, then steadily
pull the entire length of the knife
blade through the slot towards you,
maintaining a constant light pressure.
The rate at which you pull the knife
•
should be about 4cm per second, so a
20cm blade will take about 5 seconds. Do
not pause as you withdraw the knife.
If the knife blade has a curved cutting edge near its end, raise the handle as you
•
withdraw the end of the blade, so as to keep the cutting edge in line with the slot.
Grind one side of the knife using one of the Coarse Grind Knife Slots1. 1or 2, as
described in A and B.
Repeat for the other side of the knife in the other Coarse Grind Knife Slot2. 2or
1.
Repeat steps 1 and 2 two more times.3.
Grind one side of the knife using one of the Fine Grind Knife Slots4. 3or 4, as
described in A and B.
Repeat for the other side of the knife in the other Fine Grind Knife Slot5. 4or 3.
Repeat steps 4 and 5 two more times.6.
Set the ON/OFF Switch7. 3to the OFF position, to switch the sharpener off.
If the knife blade has burrs after you have performed the process described in
•
steps 1 to 7 of Knife Sharpening, you can hone the blade manually, as follows:
Features
The Knife Sharpener will sharpen a large range of knives, including those that must
be ground on only one side. It will also sharpen scissors and restore damaged flat-
bladed screwdrivers.
How to use
Cutlery should be clean and dry before being sharpened and should be wiped clean•
after sharpening. Take care when wiping knives as they become extremely sharp.
Knives are sharpened by grinding in two stages - coarse grinding, then fine. At
•
each stage, most knives are sharpened on both sides, but some must be sharpened
on only one side, which is readily determined by examining the knife; the
instructions below are for knives that are sharpened on both sides.
The left hand slots
• 1and 3are used to sharpen the right hand side of the knife
1
3
2
4
5
6
With the sharpener switched off, insert the knife into the left hand Fine Grind1.
Knife Slot 3, ensuring that the cutting edge of the blade is pushed fully forward
into the slot.
Move the knife downwards, so that it is firmly in contact with the stationary2.
grinding wheel, then pull it out slowly towards you, maintaining firm contact
with the wheel.
Repeat for the other side of the knife in the right hand Fine Grind Knife Slot3. 4
Scissors Sharpening
With the sharpener switched on, insert one of the scissor blades as far forward as1.
it will go into the outer edge of the Scissor Slot 5.
In a single motion, move the scissor blade into the slot, until2.
you feel the blade is in good contact with the spinning grinding wheel,
then steadily pull the entire length of the scissor blade across the slot to
the rear of the sharpener, maintaining a constant light pressure.
Repeat steps 1 and 2 of Scissor Sharpening two more times.3.
Repeat steps 1 to 3 of Scissor Sharpening for the other scissor blade.4.
Set the ON/OFF Switch5. 3to the OFF position, to switch the sharpener off.
Screwdriver Restoring
With the sharpener switched on, insert the point of the damaged screwdriver1.
blade into the Screwdriver Slot 6, until it makes contact with the spinning
grinding wheel. Hold it in position briefly, then withdraw the screwdriver.
The grinding action is very effective, so do not use undue pressure or apply for
•
longer than a second or two at a time. Use only with flat-bladed screwdrivers.
Examine the screwdriver to determine if the damage has been repaired and2.
repeat step 1 as necessary, turning the screwdriver through 180° each time.
Set the ON/OFF Switch3. 3to the OFF position, to switch the sharpener off.
Cleaning & Care
10
11
7
8
9
6
The body of the Knife Sharpener will require only•
occasional wiping with a slightly damp cloth.
Dust from the grinding process is collected in the two•
magnetic waste drawers 8and 9. These should be
removed periodically from the rear of the sharpener
and wiped clean with a damp cloth or tissue.
Note: The drawers are not interchangeable and must be
replaced in their original positions. 8
9
Page 4Page 3Page 2