JUITA JT-1512B User manual

Attention: read this manual please, when
using this product
JT-1512B
Garment Template Cutting Machine
(USER MANUAL)
Microsoft is a U.S. registered trademark of Microsoft Corporation. Windows
is a registered trademark of Microsoft Corporation

Preface
Thanks for choosing the JUITA Template Cutting Machine.
The JUITA enjoys not only the beautiful design but also the high
precision, strong compatibility, which can operate with the CAD of
HPGL. Besides, it operates fast and stable.
Before using this template cutting machine, you’d better read this
manual to make sure that you will work with it effectively. If you have
any questions, you will go to the local sellers for further help!
With the easy upgrading of the garment template cutting machine and its
plotting software, we will develop and improve their functions to meet
our customers’ individual demands. This manual is subject to change
without notice. If you have any questions, please contact us.

Chapter 1. Safety Notice
Safety notice: before using this template cutting machine, please read the
following instructions:
1. The template cutting machine should be installed horizontally. If the template
cutting machine is in uneven status, it cannot work normally.
2. After installation, you should adjust the height of stand until the machine is in a
horizontal state. The GTCM shall not be installed on the vibrating or unstable
ground.
3. Please connect this machine to the power supply according to the machine’
rated voltage. Don’t connect the GTCM to the socket with unstablevoltage.
The unstable power may result in the performance degradation, and damage
the power panel. If the power is not stable, please install the regulator.

4. The plug should be connected to the panel with the ground wire. Don’t move
out plug’s needle. If the machine is not connected with the ground wire, the
ESD will harm the human body and damage the parts of the machine.
5. Don’t connect the GTCM with the photoprinter, air-conditioner or other power
consumption machines on the same line. If the GTCM is connected with
other power consumption machine in parallel, the sum of their power should
not be bigger than the max power of the plug.
6. Don’t use the wearing power line. Please pull the plug out of the socket when
the machine is not used in a long time.
7. When you clean the GTCM firstly, you have to pull the plug out. Don’t let the
liquid draw into the machine, otherwise it may cause short circuit or damage
to the template cutting machine.
8. Don’t maintenance or dismantle this machine without any instructions that
stated in this manual. Don’t clog or place other goods in the machine working
room.
9. During the operation of the GTCM, don’t put your hands into the machine or
touch the trolley and otherparts.

Model of the
Product
Series Number of the product
Please check whether the voltage
of AC power corresponds to the
marked voltage on the label.
Chapter 2. Application Notice
Whether you are familiar with the template cutting machine for garment
template or not, please read the following application notice:
2.1 application condition
(1) The operating temperature range of o Celsius to 35 Celsius. Don’t put or
operate this machine under the intense light, radiation or the thermal
energy.
(2) The operating humidity under room temperature ranges from 20% to
80%. Don’t use the machine in the wet and dust condition. Once the
water vapor condensed in the machine with the dust, the short circuit or
bad contact will happen, which effects the operation of the machine.
(3) Don’t put the milling plotter in the harsh EMI environment or beside the
magnetic items.

2.2 other notices:
(1) Don’t move the GTCM’s holder by hand, otherwise the GTCM may be
damaged.
(2) Except take on or off the GTCM, don’t screw the fixed nuts on the
holder.
(3) Don’t add lubricant into the , otherwise the machine may not
operate very well.
(4) After using the GTCM, please cover the dust proof.
(5) Don’t switch on or off the machine unnecessarily, otherwise it may affect
the functions of the electronic components.
(6) During the operation, don’t stand against to the machine or put hands on
the track’s cover.
(7) If you want to connect or regulate the signal wire, you should make sure
the machine is power off.

3.1 Introduction
Chapter 3. Introduction
The garment template cutting machine mainly deals with the
cutlery of the complicated graphs or words. With high precision and
stability, it enjoys beautiful design. Except that, it is also easily to
control with.
Specification
Material : Nonmetal; Single piece or in a roll;
Original coordinate setting：setting the original point by user.
Max speed of milling and drawing：1200mm/sec
Mechanical resolution：0.025mm/step
Software resolution：0.025mm/step
Distance accuracy：0.15% or 0.1mm
Minimum size of character：5mm*5mm
Repeat position precision：≤0.2mm
Pressure of the tool：50G-500G
Movement acceleration：5g
Communication ：USB2.0，blue tooth transmitting；
Embedded processer：Using 32Bits DSP with 256Mb
Motor driver：AC servo motor driver
Plotting tool movement speed：50 times/sec

Power Supply：170V/250v 50-60H 300W(max)
3.2 requirement of the software and hardware ：
The CAD/CAM software should be compatible with the HP-GL：
Select the software that support the HP-GL；special format can be
ordered；
Hardware：Better than the minimum of the mainstream computer
3.3 consumptive materials
Tools：milling tools of 2—4MM 、special cutting tools
Material: PVC sheet、Kraft paper in roll、single kraft paper、and other
materials.

Chapter 4. Installation
4.1 The items included in the packing of the machine:
1、machine table 1
□
2、lateral stand 2
□
3、support beam 4
□
4、power cable 1
□
5、signal cable 1
□
6、roll paper bar 1
□
7、cutter holder 1、pen holder 1
□
8、screw 10、inner hexagon spanner 2
□
9 milling tool 2、a box of cutting tools
□
10、Manual 1
□
12、warranty card
□
13、CD 1
□
4.2 Installation of the Stand and the machine table: (the instructor of the
machine as following pictures)

(1) firstly, installing the support beam and the two lateral stand.
(2) after fixing the whole support, put the machine table on the support
and tighten the screw.
(3) using the leveller for testing whether the machine table is horizontal.
4.3 Install paper：
Place the paper roller onto a chart drum. First, put the chart drum onto the
paper supporting shaft as illustrated in the graph and move it to the right
place; hold the fixtures tightly on both sides; and then tighten the
fastening screw.
(1) Firstly, the GTCM shall be inserted into the appropriative knife shell
and tightened by the screw.
(2) After resetting: Using the tele controller to press the key No. 12 in
order to make the spindle case move to the reset position.

(3) The spindle motor shall be put on the spindle case carefully which is
on the lowest position, in order to let the point of milling cutter be in the
same horizontal plane with the limit device. Then, the spindle motor
should be tightened by the screw.

(4) After that, according to the thickness of sheet, filling the options in
the MarkCad.
Remark: Because the error on the height of the spindle motor is
introduced after the changing of milling tool, this error should be
calculated before working. The calculation method is stated as follows:
1. If you use the sheet thickness of 1mm for test, you should fill 0.8 or
less in the Mark Cad. Then, you shall mill that sheet by the machine and
test whether it can be cut through.
2. If it can not be cut through, you should increase the thickness value
that you fill in the Markcad.
3. If the sheet is milled through, you should test whether it is milled too
deep. If it is milled too deep, you should decrease the thickness value that

you fill in the Mark cad.
4. If the sheet thickness is 0.8 in the Mark Cad by 1MM, the error is 0.2.
Then you should minus 0.2 from the sheet thickness which you use in
your work when you change the sheet of the different thickness.
5. If you use 2MM, you should fill the 1.8MM as the sheet thickness in
the MarkCad.
4.5 connecting to the power supply and the computer
(1) Make sure the machine is switched-off and make sure the power
supply is 110V/220V, then connect the power cable with the power
supply.
(2) According to the computer setting, the USB communication line
should be connected to the ports of the machine and the computer.
Then, fix the Support. Before the above installation, the machine
and the computer have to be power off.
4.6 The installation of control center software to the computer
(1) The file compression in the CD that is in the packing box
for the machine need to be copied into the computer and

decompress it. Opening the folder, you will see
. Then you send it to the desktop as
shortcut.
(2) Switching on the template machine, the computer and the
plotter will begin to initiate the connection……(as the following
picture shows)
Notice: on the right and the bottom of
the monitor, there is a notice for a
new disk, and the following dialog
box appears.
Click the NEXT, as follows:
Select , then click as
following picture:

Select then click
BROWSE(as following picture)
The driver track of the milling plotter is :
C:\平台切割绘图机闪电- V2.0\Driver\
select 确定 OK , then click NEXT (as the
following picture shows)

remain the original option，click NEXT(as the
following picture shows)
At the end, click 完 成 OK，finish the installation of the
new disk. Then, open , the following picture will appear：
Click “YES”, it will synchronize with the
original adjusted parameter.
4.7 Switch on the machine

Firstly release the red button, and then press the green one in the
middle:
主电源按钮： Main power supply button
启动按钮： Start Button
风机按钮：Fan Button
Chapter 5. Software
5.1 Information for the interface of software (ATTENTION: before
opening the software, you should connect the computer to the
machine and make sure the machine is power on, otherwise the
software cannot be opened.)

(1) menu bar:
this includes the settings for the
main functions of the software
(2) Tool bar:
(2.1) If you press this button, the mapping file from the other
folder except the acquiescent folder of the software will be copied in to
that acquiescent folder, and appear on the file list. The operating way is :
1) click the , the above window will appear.

2) find your folder that has the mapping file and select the file that
you want to draw or cut.
3) click” OPEN”, if it operates well, the system will appear
such instructions
4) at this time, the input file will be on the bottom of the
listed file.
(2.2) this button is designed for the automatic drawing. Click
this button; the output center will enter into the automatic printing
state and follow your way to deal with the file.
(2.3) click this button, it will begin Plotting and milling.
(2.4) click this button, it will stop working.
(2.5) click this button, the picture which is used now will be
zoom in.
(2.6) click this button, the picture which is used now will be
zoom out
(2.7) click this button, you can extract the contours of the image.
The contours’ line will appear on the display box, which is also the
milling line.
(2.8) click this button, the file will be deleted. You can delete
the unnecessary file from the list box and the acquiescent folder.
(2.9) click this button, you can extract the milling line manually.
(Examples 2.14 show it)