Jumper JPD-HA120 User manual

Version: 2.2
Revision Date: 2022.04
Electronic Blood Pressure Monitor
JPD-HA120 User Manual

- 1 -
Product Composition
The product is comprised of the host machine and the cuff of Electronic
Blood Pressure Monitor.
Application Scope
The Electronic Blood Pressure Monitor is used to measure the diastolic
pressure, systolic pressure and pulse rate of adults by oscillometric
method for diagnostic reference.

- 2 -
The warnings and illustrations shown in the User Manual enable you to
use the product safely and correctly, thus preventing you and others
from being injured, specifically as follows:
Legend, mark and meaning
Warning message
Anti-electric shock degree is Type BF of the
application part
When the product life expires and the end users
discard the products, send them to the designated
collecting and separating place for disposal
according to the requirements from the local
environmental protection authority.
Consult the instructions for use.
This product complies with the MDD93/42/EEC
requirements.
IP21
Degree of protection against the ingress of water.
Information of manufacturer
Date of manufacture
Authorized European Representative
Safety Precautions

- 3 -
Avoid smoking, eating, drinking caffeinated drinks or exercising for 30
minutes before taking measurement.
1. Sit upright in a chair with both feet on the floor.
2. Remove tight fitting clothing from your upper arm along with any
thick clothing.
3. Pull on the end of the cuff until it wraps securely
around your upper arm. Place your arm on a table so
that the cuff will be at the same level as your heart.
4. The cuff will automatically inflate and the
measurement will start, upon pressing the
“START/STOP” button.
5. When the measurement is complete, the cuff will automatically
deflate and your systolic and diastolic pressure values and pulse rate will
be displayed.
Quick Start Guide

- 4 -
Monitor
Features
Universal Cuff
99 Readings * 2 Users
Average of last 3 readings
Irregular Heartbeat Detector
Auto-off Power Saving Feature
Bluetooth Transmission Function
Operated by 4 AA batteries (USB 5V optional)
Overview

- 5 -
Display
Packing List
No.
Name
Quantity
1
Electronic Blood Pressure Monitor
1
2
Cuff
1
3
Dry Battery (AA)
4
4
User Manual
1
5
Zipped Carrying Bag
1

- 6 -
2.1 Battery Installation
a）Open the battery cover as shown in
the picture.
b）Place 4 AA dry batteries. Pay
attention to the battery electrode
indication.
2.2 Battery power indication and replacement
After the product is turned on, if low power symbol appears on
the screen , the measurement cannot be performed, and the battery must
be replaced.
Do not use any expired battery;
If the product is not used for over 3 months, please
take out the batteries.
2.3 USB Power Supply
USB line can be connected for power supply of the product without
battery.
Preparation

- 7 -
2.4 Cuff
The applicable arm circumference range of the cuff is 22-36cm or
22-42cm.
Connection: Insert the air plug of cuff air tube into air jack of the
Electronic Blood Pressure Monitor. Figure shown as above:

- 8 -
3.1 User mode
Switch between “User 1” and “User 2” can be processed in the “OFF”
state or upon the measurement completion, by short press on the
“USER” button.
3.2 Year/Month/Date/Time setting
In the “OFF” state, enter the setting mode by long press on the “USER”
button for 3~5s.
After entering the “Year” setting mode, the flashing 20XX will show on
the screen. Press the “MEM” button, and the value will be incremented
among 2019 and 2099. Press the “USER” button for “Year” value
confirmation and move to the “Month” setting mode.
After entering the “Month” setting mode, 1/01 will flash on the screen.
Press the “MEM” button, and the value will be incremented among 1
and 12. Press the “USER” button for “Month” value confirmation and
Function Setting Mode

- 9 -
enter the “Date” setting mode.
After entering the “Date” setting mode, 1/01 will flash on the screen.
Press the “MEM” button, and the value will be incremented among 01
and 31. Press the “USER” button for “Date” value confirmation and
enter the “Time” setting mode.
After entering the “Time” setting mode, XX:XX will flash on the screen.
Press the “MEM” button, and the “Hour” value will be incremented
among 1~12 AM/PM. Press the “USER” button for “Hour” value
confirmation and enter the “Minute” setting mode. Press the “MEM”
button, and the value will be incremented among 00 and 59.
Note:
When setting time values, continue pressing the "MEM" button till the
correct values are well set. Value ranges are year (2019~2099), month
(01~ 12), date (01~31), hour (1~12 AM/PM) and minute (00~59). When
the ceiling value of a certain time sector is reached, the relevant value of