Juniper SRX 1400 SERVICES GATEWAY - User manual

SRX1400 Services Gateway Getting
Started Guide
June 2016
Part Number: 530-071199
Revision 01
Contents AboutThisGuide....................................................3
DocumentOrganization...........................................3
Safety Recommendations Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SRX1400 Services Gateway Definition of Safety Warning Levels . . . . . . . . . . . 4
SRX1400 Services Gateway General Safety Guidelines and Warnings . . . . . . 6
Introduction to the SRX1400 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
SRX1400 Services Gateway Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
SRX1400ServicesGatewayModels..................................7
SRX1400 Services Gateway Chassis Specifications . . . . . . . . . . . . . . . . . . . . . 8
SRX1400 Services Gateway Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SRX1400 Services Gateway Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Step 1: Prepare the Site for SRX1400 Services Gateway Installation . . . . . . . . . . . 11
Site Preparation Checklist for SRX1400 Services Gateway . . . . . . . . . . . . . . . 11
SRX1400 Services Gateway Rack Requirements . . . . . . . . . . . . . . . . . . . . . . . 12
Step 2: Unpack the SRX1400 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Unpack the SRX1400 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Verify Parts Received with the SRX1400 Services Gateway . . . . . . . . . . . . . . 15
Step 3: Install the SRX1400 Services Gateway Mounting Hardware . . . . . . . . . . . 17
Step 4: Install the SRX1400 Services Gateway in a Rack . . . . . . . . . . . . . . . . . . . . 17
Install the SRX1400 Services Gateway in a Rack Manually (Without a
MechanicalLift).............................................18
Remove Components from the Chassis for Manual Lifting of the
SRX1400ServicesGateway................................19
Lift the SRX1400 Services Gateway Chassis into the Rack . . . . . . . . . . . 19
Reinstall Components into the SRX1400 Services Gateway Chassis . . . 21
Step 5: Connect the External Devices and IOC Cables to the SRX1400 Services
Gateway .......................................................21
Connect the SRX1400 Services Gateway to a Network for Out-of-Band
Management................................................21
Connect the SRX1400 Services Gateway to a Management Console . . . . . . 22
1Copyright © 2016, Juniper Networks, Inc.

Connect the Ethernet Network Cables to the SRX1400 Services
Gateway ...................................................23
Step 6: Connect the Ground and Power Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Connect the Grounding Cable to the SRX1400 Services Gateway . . . . . . . . . 25
Connect Power to an AC-Powered SRX1400 Services Gateway . . . . . . . . . . 26
Connect Power to a DC-Powered SRX1400 Services Gateway . . . . . . . . . . . 29
Power On the SRX1400 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Power Off the SRX1400 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Step 7: Perform the Initial Software Configuration on the SRX1400 Services
Gateway.......................................................32
SRX1400 Services Gateway Software Configuration Overview . . . . . . . . . . . 32
Perform Initial Software Configuration on the SRX1400 Services Gateway
(CLIProcedure).............................................33
Step 8: Monitor the SRX1400 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . 37
SRX1400 Services Gateway Compliance Statements for EMC Requirements . . . 37
Canada .......................................................37
EuropeanCommunity............................................38
Japan.........................................................38
United States ..................................................38
SRX Series Documentation and Release Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
RequestingTechnicalSupport........................................39
Self-Help Online Tools and Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
OpeningaCasewithJTAC........................................39
RevisionHistory....................................................40
Copyright © 2016, Juniper Networks, Inc.2
SRX1400 Services Gateway Getting Started Guide

About This Guide
This guide contains the basic information you need to install and configure the SRX1400
Services Gateway quickly. For complete installation instructions, and instructions for
installing additional modules such as cards and power supplies, see the SRX1400 Services
Gateway hardware documentation at www.juniper.net/techpubs/.
•Document Organization on page 3
Document Organization
The SRX1400 Services Gateway Getting Started Guide provides background information
and step-by-step instructions for getting started with the SRX1400 Services Gateway.
Table 1 on page 3 summarizes the information included in each topic of this guide.
Table 1: SRX1400 Services Gateway Document Organization
ContentsTopic
Provides important safety recommendations and
considerations for you to be aware of before you
attempt to install the services gateway.
“Safety Recommendations Before You
Begin” on page 4
Describes the SRX1400 Services Gateway and
summarizes the available models. It includes
physical specifications about the chassis and
provides information about the components on the
front and back panels.
“Introduction to the SRX1400 Services
Gateway” on page 7
Provides a site preparation checklist, rack
requirements, and instructions for connecting the
services gateway to the building structure.
“Step 1: Prepare the Site for SRX1400
Services Gateway Installation” on page 11
Explains how to unpack the services gateway and
lists the required tools. It includes a list of
components and accessories shipped with the
services gateway for you to verify.
“Step 2: Unpack the SRX1400 Services
Gateway” on page 13
Describes the specific mounting hardware required
for installing the device in a rack.
“Step 3: Install the SRX1400 Services
Gateway Mounting Hardware” on page 17
Provides a step-by-step procedure for installing the
services gateway.
“Step 4: Install the SRX1400 Services
Gateway in a Rack” on page 17
Describes how to connect the external devices and
I/O card (IOC) cables to the services gateway.
“Step 5: Connect the External Devices and
IOC Cables to the SRX1400 Services
Gateway” on page 21
Describes how to connect, ground, and power on
the services gateway.
“Step 6: Connect the Ground and Power
Cables” on page 24
3Copyright © 2016, Juniper Networks, Inc.
About This Guide

Table 1: SRX1400 Services Gateway Document Organization (continued)
ContentsTopic
Describes how to perform initial software
configuration using the CLI.
“Step 7: Perform the Initial Software
Configuration on the SRX1400 Services
Gateway” on page 32
Describes how to monitor the services gateway using
LEDs and chassis alarm conditions.
“Step 8: Monitor the SRX1400 Services
Gateway” on page 37
Presents EMC compatibility compliance statements.“SRX1400 Services Gateway Compliance
Statements for EMC Requirements” on
page 37
For more information, see the SRX1400 Services Gateway hardware documentation at
www.juniper.net/techpubs/.
Safety Recommendations Before You Begin
This topic provides important safety recommendations and considerations for you to
review before you attempt to install the services gateway. It contains the following
sections:
•SRX1400 Services Gateway Definition of Safety Warning Levels on page 4
•SRX1400 Services Gateway General Safety Guidelines and Warnings on page 6
SRX1400 Services Gateway Definition of Safety Warning Levels
This guide uses the following levels of safety warnings:
NOTE: You might find this information helpful in a particular situation or
might otherwise overlook it.
CAUTION: You need to observe the specified guidelines to avoid minor injury
or discomfort to you or severe damage to the services gateway.
WARNING: This symbol alerts you to the risk of personal injury from a laser.
WARNING: This symbol means danger. You are in a situation that could cause
bodily injury. Before you work on any equipment, be aware of the hazards
involved with electrical circuitry and be familiar with standard practices for
preventing accidents.
Copyright © 2016, Juniper Networks, Inc.4
SRX1400 Services Gateway Getting Started Guide

Waarschuwing Dit waarschuwingssymbool betekent gevaar. U verkeert in
een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige
apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische
schakelingen betrokken risico's en dient u op de hoogte te zijn van standaard
maatregelen om ongelukken te voorkomen.
Varoitus Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi
johtaa ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa,
ota selvää sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista
onnettomuuksien ehkäisykeinoista.
Attention Ce symbole d'avertissement indique un danger. Vous vous trouvez
dans une situation pouvant causer des blessures ou des dommages corporels.
Avant de travailler sur un équipement, soyez conscient des dangers posés
par les circuits électriques et familiarisez-vous avec les procédures
couramment utilisées pour éviter les accidents.
Warnung Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer
Situation, die zu einer Körperverletzung führen könnte. Bevor Sie mit der
Arbeit an irgendeinem Gerät beginnen, seien Sie sich der mit elektrischen
Stromkreisen verbundenen Gefahren und der Standardpraktiken zur
Vermeidung von Unfällen bewußt.
Avvertenza Questo simbolo di avvertenza indica un pericolo. La situazione
potrebbe causare infortuni alle persone. Prima di lavorare su qualsiasi
apparecchiatura, occorre conoscere i pericoli relativi ai circuiti elettrici ed
essere al corrente delle pratiche standard per la prevenzione di incidenti.
Advarsel Dette varselsymbolet betyr fare. Du befinner deg i en situasjon som
kan føre til personskade. Før du utfører arbeid på utstyr, må du vare
oppmerksom på de faremomentene som elektriske kretser innebærer, samt
gjøre deg kjent med vanlig praksis når det gjelder å unngå ulykker.
Aviso Este símbolo de aviso indica perigo. Encontra-se numa situação que
lhe poderá causar danos físicos. Antes de começar a trabalhar com qualquer
equipamento, familiarize-se com os perigos relacionados com circuitos
eléctricos, e com quaisquer práticas comuns que possam prevenir possíveis
acidentes.
¡Atención! Este símbolo de aviso significa peligro. Existe riesgo para su
integridad física. Antes de manipular cualquier equipo, considerar los riesgos
que entraña la corriente eléctrica y familiarizarse con los procedimientos
estándar de prevención de accidentes.
Varning! Denna varningssymbol signalerar fara. Du befinner dig i en situation
som kan leda till personskada. Innan du utför arbete på någon utrustning
måste du vara medveten om farorna med elkretsar och känna till vanligt
förfarande för att förebygga skador.
5Copyright © 2016, Juniper Networks, Inc.
SRX1400 Services Gateway Definition of Safety Warning Levels

Related
Documentation
SRX1400 Services Gateway General Safety Guidelines and Warnings on page 6•
SRX1400 Services Gateway General Safety Guidelines and Warnings
The following guidelines help ensure your safety and protect the services gateway from
damage. The list of guidelines might not address all potentially hazardous situations in
your working environment, so be alert and exercise good judgment at all times.
•Perform only the procedures explicitly described in this guide. Make sure that only
authorized service personnel perform other system services.
•Keep the area around the chassis clear and free from dust before, during, and after
installation.
•Keep tools away from areas where people could trip on them.
•Do not wear loose clothing or jewelry, such as rings, bracelets, or chains, which could
become caught in the chassis.
•Wear safety glasses if you are working under any conditions that could be hazardous
to your eyes.
•Do not perform any actions that create a potential hazard to people or that make the
equipment unsafe.
•Never attempt to lift an object that is too heavy for one person to handle.
•Never install or manipulate wiring during electrical storms.
•Never install electrical jacks in wet locations unless the jacks are specifically designed
for wet environments.
•Operate the services gateway only when it is properly grounded.
•Do not open or remove chassis covers or sheet metal parts unless instructions are
provided in this guide. Such an action could cause severe electrical shock.
•Do not push or force any objects through any opening in the chassis frame. Such an
action could result in electrical shock or fire.
•Avoid spilling liquid onto the services gateway chassis or onto any services gateway
component. Such an action could cause electrical shock or could damage the services
gateway.
•Avoid touching uninsulated electrical wires or terminals that have not been
disconnected from their power source. Such an action could cause electrical shock.
Related
Documentation
SRX1400 Services Gateway Definition of Safety Warning Levels on page 4•
•Site Preparation Checklist for SRX1400 Services Gateway on page 11
Copyright © 2016, Juniper Networks, Inc.6
SRX1400 Services Gateway Getting Started Guide

Introduction to the SRX1400 Services Gateway
This topic includes the following sections:
•SRX1400 Services Gateway Description on page 7
•SRX1400 Services Gateway Models on page 7
•SRX1400 Services Gateway Chassis Specifications on page 8
•SRX1400 Services Gateway Front Panel on page 9
•SRX1400 Services Gateway Back Panel on page 11
SRX1400 Services Gateway Description
Juniper Networks SRX1400 Services Gateway expands the SRX Series family of
next-generation security platforms, delivering performance and service integration to
environments that require the features without the massive scalability and aggregated
throughput provided by Juniper Networks SRX3000 line and SRX5000 line. The SRX1400
Services Gateway provides firewall support with key features such as IP Security (IPsec),
virtual private network (VPN), and high-speed deep packet inspection features such as
Intrusion Detection and Prevention (IDP). The SRX1400 device is suited for small to
medium data centers, enterprises, and service provider network security deployments
where consolidation of security functionality, uncompromised performance, and compact
environmental footprint are requirements.
The SRX1400 Services Gateway runs the Junos operating system (Junos OS).
Related
Documentation
SRX1400 Services Gateway Models on page 7•
•SRX1400 Services Gateway Chassis Specifications on page 8
•SRX1400 Services Gateway Front Panel on page 9
•SRX1400 Services Gateway Back Panel on page 11
SRX1400 Services Gateway Models
The SRX1400 Services Gateway is available in four models, which are listed in
Table 2 on page 7.
Table 2: SRX1400 Services Gateway Models
Device TypeModel Number
SRX1400 Services Gateway with 1-Gigabit Ethernet System
I/O card (SYSIOC), and AC power supply
SRX1400BASE-GE-AC
SRX1400 Services Gateway with 1-Gigabit Ethernet SYSIOC,
and DC power supply
SRX1400BASE-GE-DC
SRX1400 Services Gateway with 10-Gigabit Ethernet SYSIOC,
and AC power supply
SRX1400BASE-XGE-AC
7Copyright © 2016, Juniper Networks, Inc.
Introduction to the SRX1400 Services Gateway

Table 2: SRX1400 Services Gateway Models (continued)
Device TypeModel Number
SRX1400 Services Gateway with 10-Gigabit Ethernet SYSIOC,
and DC power supply
SRX1400BASE-XGE-DC
NOTE: The SRX1400 Services Gateway base models include the Routing
Engine, SYSIOC, and power supply. The Network and Services Processing
Card (NSPC) and IOCs are not provided with the SRX1400 Services Gateway
base models. You must order them separately. Contact your Juniper Networks
customer service representative for more information.
Related
Documentation
SRX1400 Services Gateway Description on page 7•
•SRX1400 Services Gateway Chassis Specifications on page 8
SRX1400 Services Gateway Chassis Specifications
Figure 1 on page 8 shows the SRX1400 Services Gateway chassis.
Figure 1: SRX1400 Services Gateway Chassis
g033500
Table 3 on page 8 lists the chassis specifications for the SRX1400 Services Gateway
chassis.
Table 3: SRX1400 Services Gateway Physical Specifications
ValueSpecification
5.25 in. (13.3 cm), 3 rack units (U)Chassis height
17.5 in. (44.5 cm)Chassis width
13.8 in. (35.05 cm)Chassis depth
Copyright © 2016, Juniper Networks, Inc.8
SRX1400 Services Gateway Getting Started Guide

Table 3: SRX1400 Services Gateway Physical Specifications (continued)
ValueSpecification
•Base chassis: 29.3 lb (13.3 kg)
•Fully configured chassis: 42.5 lb (19.3 kg)
Chassis weight
The SRX1400 Services Gateway is 3 U tall. Sixteen devices can be stacked in a single
floor-to-ceiling rack, for increased port density per unit of floor space.
The device provides common form-factor module (CFM) slots that you can populate
with the following cards:
•Double-wide NSPC in adjacent CFM slots 1 and 3
•IOC, SPC, or NP-IOC in slot CFM 2
For detailed information about the modules supported by the services gateway, see the
SRX1400, SRX3400, and SRX3600 Services Gateway Module Guide at
www.juniper.net/techpubs/.
The device also has one dedicated slot for a SYSIOC, one dedicated slot for the Routing
Engine, two slots for power supplies, and one slot for the fan tray and air filter.
Table 4 on page 9 lists the minimum system configuration for the SRX1400 Services
Gateway.
Table 4: SRX1400 Services Gateway Minimum System Configuration
MinimumComponent
1NSPC
1Routing Engine
1SYSIOC
1Power supply
1Fan tray
Related
Documentation
SRX1400 Services Gateway Models on page 7•
•SRX1400 Services Gateway Front Panel on page 9
•SRX1400 Services Gateway Back Panel on page 11
SRX1400 Services Gateway Front Panel
Figure 2 on page 10 shows the front panel of the SRX1400 Services Gateway.
9Copyright © 2016, Juniper Networks, Inc.
SRX1400 Services Gateway Front Panel

Figure 2: SRX1400 Services Gateway Front Panel
g033501
1
4 5 6
2 3
Table 5 on page 10 lists the components on the front panel of the services gateway.
Table 5: SRX1400 Services Gateway Components on the Front Panel
ComponentNumber
Network and Services Processing Card (NSPC) in adjacent CFM slots
1 and 3
1
Routing Engine2
System I/O card (SYSIOC)3
CFM slot 24
Power supply5 and 6
Related
Documentation
SRX1400 Services Gateway Description on page 7•
•SRX1400 Services Gateway Chassis Specifications on page 8
•SRX1400 Services Gateway Back Panel on page 11
Copyright © 2016, Juniper Networks, Inc.10
SRX1400 Services Gateway Getting Started Guide

SRX1400 Services Gateway Back Panel
Figure 3 on page 11 shows the back panel of the SRX1400 Services Gateway.
Figure 3: SRX1400 Services Gateway Back Panel
g033502
1
Table 6 on page 11 lists the components on the back panel of the SRX1400 Services
Gateway.
Table 6: SRX1400 Services Gateway Components on the Back Panel
ComponentNumber
Fan tray assembly1
Related
Documentation
SRX1400 Services Gateway Front Panel on page 9•
•SRX1400 Services Gateway Description on page 7
Step 1: Prepare the Site for SRX1400 Services Gateway Installation
This topic describes site preparation and services gateway rack requirements. It includes
the following sections:
•Site Preparation Checklist for SRX1400 Services Gateway on page 11
•SRX1400 Services Gateway Rack Requirements on page 12
Site Preparation Checklist for SRX1400 Services Gateway
Table 7 on page 11 summarizes the tasks you need to perform when you are preparing
a site for installing the SRX1400 Services Gateway.
Table 7: Site Preparation Checklist
Date
Performed
ByItem or Task
Verify that environmental factors such as temperature and humidity do
not exceed services gateway tolerances.
Select the type of rack.
11Copyright © 2016, Juniper Networks, Inc.
SRX1400 Services Gateway Back Panel

Table 7: Site Preparation Checklist (continued)
Date
Performed
ByItem or Task
Plan rack location, including required space clearances.
If a rack will be used, secure it to the floor and building structure.
Obtain cables and connectors.
Locate sites for connection of system grounding.
Measure the distance between the external power sources and the device
installation site.
Calculate the optical power budget and optical power margin.
For more information, see the SRX1400 Services Gateway hardware documentation at
www.juniper.net/techpubs/.
Related
Documentation
SRX1400 Services Gateway Rack Requirements on page 12•
•SRX1400 Services Gateway General Safety Guidelines and Warnings on page 6
SRX1400 Services Gateway Rack Requirements
The SRX1400 Services Gateway can be installed in a rack. Many types of racks are
acceptable, including open-frame racks and four-post (telco) racks. However,
front-mounting the SRX1400 Services Gateway in a two-post rack is the preferred method
of installation.
Table 8 on page 12 describes the rack requirements for the services gateway.
Table 8: SRX1400 Services Gateway Rack Requirements
Specification
Rack
Requirement
The device is designed for installation into a 19-in. (48.26 cm) rack as
defined in Cabinets, Racks, Panels, and Associated Equipment (document
number EIA-310–D) published by the Electronics Industry Association
(http://www.eia.org).
Size
The rack must be strong enough to support the weight of the fully configured
device, up to 41.8 lb (19.3 kg).
If you stack 8 fully configured devices in one rack, it must be capable of
supporting up to 340.4 lb (154.4 kg).
Strength
Copyright © 2016, Juniper Networks, Inc.12
SRX1400 Services Gateway Getting Started Guide

Table 8: SRX1400 Services Gateway Rack Requirements (continued)
Specification
Rack
Requirement
The device can be mounted in any rack that provides holes or hole patterns
spaced at 1U (1.75 in.) increments.
The mounting brackets used to attach the chassis to a rack are designed
to fasten to holes spaced at those distances.
Spacing of the
mounting bracket
holes
Always secure the rack to the structure of the building. If your geographical
area is subject to earthquakes, bolt the rack to the floor.
For maximum stability, also secure the rack to ceiling brackets.
Connect to the
building structure
From the front of the chassis, there is a single air intake on the left side of
the services gateway. Air is pushed from the fan tray through the air filter
and then to the card cage. The air is exhausted out the right of the system.
For the cooling system to function properly, the airflow around the chassis
must be unrestricted.
Allow at least 6 in. (15.2 cm) of horizontal clearance between devices.
Allow 5 in. (13 cm) between the side of the chassis and any
non-heat-producing surface, such as a wall.
When you are installing the services gateway in a cabinet, allow at least 3
in. (7.6 cm) of vertical clearance between the top and bottom of the services
gateway and other devices in the cabinet.
Clearance for
airflow
For service personnel to remove and install hardware components, there
must be adequate space at the front and back of the services gateway.
At least 29.9 in. (76 cm) is required in front of the device, and at least 24
in. (61 cm) is required behind the device. NEBS GR-63 recommends that
you allow at least 30 in. (72.6 cm) in front of the rack and 24 in. (61 cm)
behind the rack.
Clearance for
hardware
maintenance
For more information on the rack requirements, see the SRX1400 Services Gateway
hardware documentation at www.juniper.net/techpubs/.
Related
Documentation
Site Preparation Checklist for SRX1400 Services Gateway on page 11•
•SRX1400 Services Gateway Chassis Specifications on page 8
•Unpack the SRX1400 Services Gateway on page 14
Step 2: Unpack the SRX1400 Services Gateway
This topic explains how to unpack the services gateway. It includes a list of components
and accessories that are shipped with the services gateway for you to verify.
•Unpack the SRX1400 Services Gateway on page 14
•Verify Parts Received with the SRX1400 Services Gateway on page 15
13Copyright © 2016, Juniper Networks, Inc.
Step 2: Unpack the SRX1400 Services Gateway

Unpack the SRX1400 Services Gateway
You need a Phillips (+) screwdriver, number 2, to unpack the services gateway.
To unpack the services gateway:
1. Move the shipping carton to a staging area as close to the installation site as possible,
where you have enough room to remove the components from the chassis.
2. Position the shipping carton with the arrows pointing up.
3. Remove the plastic handle inserts and lift the cardboard cover off the device.
4. Remove the foam covering the top of the services gateway. Figure 4 on page 14
illustrates how to unpack the services gateway.
5. Remove the accessory box and the SRX1400 Services Gateway Getting Started Guide.
Figure 4: Unpack the SRX1400 Services Gateway
g033512
6. With a person on each side of the carton, carefully lift the device from the carton and
place it on a flat, level surface. Remove the bag covering the device.
7. Verify the parts received against the list provided in “Verify Parts Received with the
SRX1400 Services Gateway” on page 15.
8. Save the carton and the packing materials in case you need to move or ship the services
gateway at a later time.
Copyright © 2016, Juniper Networks, Inc.14
SRX1400 Services Gateway Getting Started Guide

NOTE: At the time of shipment, the adjacent CFM slots 1 and 3 are covered
with a filler cover and slot 2 is covered with a blank panel. Save the filler
cover and the blank panel after removing them from the slots, in case you
need them when you pack or move the chassis at a later time. The filler
cover is bare metal, without a colored overlay.
9. Proceed to install the services gateway.
Related
Documentation
Install the SRX1400 Services Gateway Mounting Hardware in a Rack on page 17•
•SRX1400 Services Gateway Rack Requirements on page 12
•Site Preparation Checklist for SRX1400 Services Gateway on page 11
•Verify Parts Received with the SRX1400 Services Gateway on page 15
•SRX1400 Services Gateway General Safety Guidelines and Warnings on page 6
Verify Parts Received with the SRX1400 Services Gateway
The parts shipped with your device can vary, depending on the configuration you ordered.
NOTE: If any part is missing, contact your Juniper Networks customer service
representative.
A fully configured services gateway contains the chassis with installed components,
listed in Table 9 on page 15, and an accessory box, which contains the parts listed in
Table 10 on page 16.
Table 9: Parts List for a Fully Configured SRX1400 Services Gateway
QuantityComponent
1Chassis, including backplane, and rack-mounting
brackets
1NSPC
1Routing Engine
1SYSIOC
1 and up to 2Power supplies
1Fan tray
1Air filter
15Copyright © 2016, Juniper Networks, Inc.
Verify Parts Received with the SRX1400 Services Gateway

Table 9: Parts List for a Fully Configured SRX1400 Services
Gateway (continued)
QuantityComponent
•1 filler cover for the adjacent CFM slots 1 and
3
NOTE: The filler cover does not have a
colored overlay.
•1 blank panel for the CFM slot 2
Cover for empty CFM slot
1AC power cord
NOTE: The NSPC is not a part of the base chassis configuration. You must
order it separately. Contact your Juniper Networks customer service
representative for more information.
Table 10: Accessory Box Parts List
QuantityPart
1Rack mount kit
1RJ-45-to-DB-9 cable to connect the services gateway through the serial port
1Juniper Networks Product Warranty
1End User License Agreement
1SRX1400 Services Gateway Getting Started Guide
1Documentation Information Card
1Product Registration
1Juniper Compliance Form Letter; Reduction of Hazardous Substances (RoHS)
1Document sleeve
1ESD wrist strap with cable
Related
Documentation
Unpack the SRX1400 Services Gateway on page 14•
•Install the SRX1400 Services Gateway Mounting Hardware in a Rack on page 17
Copyright © 2016, Juniper Networks, Inc.16
SRX1400 Services Gateway Getting Started Guide

Step 3: Install the SRX1400 Services Gateway Mounting Hardware
The specific mounting hardware used depends on the type of rack you are using. Follow
the appropriate steps for your rack to install the mounting hardware.
To install the mounting hardware:
1. Locate the rack-mounting brackets in the accessory kit.
2. Position a mounting bracket on each side of the chassis. You can position the brackets
in front-mount or rear-mount position.
3. Use the screws provided to secure the rack-mounting brackets to the sides of the
chassis as shown in Figure 5 on page 17.
Figure 5: Attaching Mounting Brackets to the SRX1400 Services Gateway
g033513
Related
Documentation
Unpack the SRX1400 Services Gateway on page 14•
•Verify Parts Received with the SRX1400 Services Gateway on page 15
•Install the SRX1400 Services Gateway in a Rack Manually (Without a Mechanical Lift)
on page 18
•SRX1400 Services Gateway General Safety Guidelines and Warnings on page 6
Step 4: Install the SRX1400 Services Gateway in a Rack
You can front-mount or rear-mount the services gateway in a two-post rack, a four-post
rack, or a cabinet. The device can be installed manually or by using a mechanical lift.
This topic provides a step-by-step procedure for installing the device in a two-post rack
without using a mechanical lift, which is the most common method for installing the
service gateway.
For instructions on installing the device in a two-post rack, four-post rack, or a cabinet
using a mechanical lift, see the SRX1400 Services Gateway hardware documentation
at www.juniper.net/techpubs/.
You need a Phillips (+) screwdriver, number 2, to install the services gateway.
17Copyright © 2016, Juniper Networks, Inc.
Step 3: Install the SRX1400 Services Gateway Mounting Hardware

Install the SRX1400 Services Gateway in a Rack Manually (Without a Mechanical Lift)
Before you install the services gateway manually, you must remove components from
the chassis. You must reinstall the components after the services gateway is installed
in the rack.
NOTE: Do not expose the empty CFM slots during storage or transportation.
Use appropriate covers (blank panel for CFM slot 2 and filler cover for the
adjacent CFM slots 1 and 3) to prevent any dust or foreign objects from
damaging the electronics.
At least two people are needed to safely lift the chassis into the rack or cabinet. With
components removed, the chassis weighs approximately 23.3 lb (10.57 kg).
WARNING: Do not attempt to lift the chassis by the handles on the power
supplies or on the CFMs. The handles might break off, causing the chassis to
fall and inflict injury.
NOTE: For safety instructions you should read before you install the services
gateway in a rack, see the SRX1400 Services Gateway hardware
documentation at www.juniper.net/techpubs.
To install the device manually without using a lift:
•Remove Components from the Chassis for Manual Lifting of the SRX1400 Services
Gateway on page 19
•Lift the SRX1400 Services Gateway Chassis into the Rack on page 19
•Reinstall Components into the SRX1400 Services Gateway Chassis on page 21
Copyright © 2016, Juniper Networks, Inc.18
SRX1400 Services Gateway Getting Started Guide

Remove Components from the Chassis for Manual Lifting of the SRX1400 Services
Gateway
To make the services gateway light enough to install manually, you must remove the
following components from the chassis:
•Power supplies
•Fan tray
The procedure in this topic is for removing components from the base model of the
chassis for initial installation only. To use this procedure, you must have not yet connected
power cables to the services gateway.
To remove the components from the services gateway:
1. Attach an ESD grounding strap to your bare wrist and connect the strap to one of the
ESD points on the chassis. For more information about ESD, see the SRX1400 Services
Gateway hardware documentation at www.juniper.net/techpubs.
2. Release each component by loosening its retaining screws and unlatching its ejector
handles, as appropriate.
3. Slide each component out of the chassis evenly so that it does not become stuck or
damaged.
4. Label each component as you remove it so you can reinstall it in the correct location.
5. Immediately store each removed component in an electrostatic bag.
6. Do not stack removed components. Set each one on a flat surface.
Lift the SRX1400 Services Gateway Chassis into the Rack
Lifting the chassis and mounting it in a rack requires two people (see Figure 6 on page 20).
Without the power supply and fan tray, the chassis weighs approximately 23 lb (10.6 kg).
1. Ensure that the rack is in its permanent location and is secured to the building.
2. Position the chassis in front of the rack.
3. With one person on each side, lift the chassis into position in the rack.
WARNING: Do not attempt to lift the chassis by the handles on the power
supplies or on the CFMs. The handles might break off and cause the chassis
to fall and inflict injury.
19Copyright © 2016, Juniper Networks, Inc.
Remove Components from the Chassis for Manual Lifting of the SRX1400 Services Gateway

Figure 6: Lift the Chassis Into the Rack
g033545
4. Align the bottom hole in each mounting bracket with a hole in each rack rail as shown
in Figure 7 on page 20.
Figure 7: Attach Mounting Hardware for Two-Post Rack
g033516
•For front-mounting the chassis in a two-post rack, align the bottom hole in each
mounting bracket at the front edge of the chassis.
•For rear-mounting the chassis in a two-post rack, align the bottom hole in each
mounting bracket at the rear edge of the chassis.
NOTE: Similarly, you can front-mount or rear-mount the chassis in a
four-post rack. However, there is no support shelf provided for the
unsupported edge on which the chassis can rest.
Copyright © 2016, Juniper Networks, Inc.20
SRX1400 Services Gateway Getting Started Guide